18 modeli
This is a basic front end barrel ring and front cover to replace the area where the white pump blaster used to be on the Motoblitz. It reduces the barrel by a few inches and increases performance and ease of handling. Turning the…
This is a buttstock extension for the Motoblitz made to add ~ 40mm in length in order to make it more comfortable for me. For installation the two halves simply slide into the rectangular slot of the Motoblitz buttstock and then you screw…
This adapter was remixed from the tungstenexe mag adapter, that was only compatible with the Nerf Stryfe, in order to make it compatible with the Motoblitz. For the printing Instruction refer to the original page of the model. I used my…
A hybrid clip-on pusher for the Nerf Motoblitz capable of pushing short darts and still fire long dats. Just print the clip upright and the pusher on its side and add a brim if needed. To install the pusher first slide the pusher part…
This battery cover was designed with an internal width of 29mm, a length of 106mm and an height of 23mm, which, combined with the 12,75mm of height of the original battery compartment arrives to 35,75mm, so it holds comfortably a 1000mAh…
I couldn't find a short dart pusher for the Motoblitz that fit and functioned properly, so I went ahead and created one myself. I've designed it to easily snap into place over the original pusher without needing to do any gluing or…
The fixes consists of some modifications to the screw posts of the models: The top rail had the screw hole deepened since it wasn't deep enough for the original screw and the screw post was lenghtened towards the rail since it was…
The Elite 2.0 Motoblitz is one of (if not the) most popular of its series, and for good reason. However, as a bullpup, I found it annoying to not have a flared magwell. So I designed one. This is a flared magwell that attaches to the…
Introduction This is an add-on for the Nerf Motoblitz, to mount it you need to first remove the white attachment normally mounted to the blaster. Hardware 4 M3x10mm socket head screws 1 M3x14mm “ ” " 3 M3x20mm “ ” " 5 M3x40mm “ ” " If you…
These files are meant to be a drop-in replacement for the magwell in the Nerf Motoblitz. The file list consists of: A replacement magwell (If you somehow lost it). A flared magwell with the back panel removed to fit older Nerf magazines…
Remixed motoblitz stock extension to have grooves to better grip your shoulder!
This is a drop-in replacement for the stock mag release on the Nerf Motoblitz. The file list consists of: A replacement mag release (If you broke the original one or if you lost it somehow). An extended mag release, adds about 2 cm more…
This is a drop-in replacement for the stock mag release on the Nerf Motoblitz. The file list consists of: A replacement mag release (If you broke the original one or if you lost it somehow). An extended mag release, adds about 2 cm more…
Rough design concept to make a modular nerf motoblitz blaster.
The unblitzing front plate is exactly the same as the original, just with a wider muzzle! There is also a custom drop-in replacement shortened barrel with side picatinny that takes the place of the stock faux barrel!
Remix and partial redesign of the original files to have slots for hardware, i completely re designed the locking plate due to the holes being misaligned for picatinny rails. Hardware required: · M3 Nut x6 · M3*16 bolt x3 · M3*30 Bolt x3
This 3D-printed short dart pusher is a non-permanent way to convert your Nerf Elite 2.0 Motoblitz to short darts. This Motoblitz Short Dart Pusher and Trigger Plug are compatible with straight or angled flywheel magazine adapters from…
The Motoblitz Flywheel Cage is a custom cage designed by Luke for the Nerf Elite 2.0 Motoblitz. It's the cage from OOD's Elite 2.0 Motoblitz 2S Mod Kit, which pairs it with Fang motors and a pair of Daybreak flywheels. FEATURES: •…
