Liczymy pasujące modele…
This model uses my locking pegboard mount system for 1" standard pegboards. Magnet holes (if present) are designed for 10mm diameter, 3mm thick magnets. “Board Attachment” parts are universal to all models. Print with 3 perimeters and…
Mounting for Voidstar Labs' Gridfinity containers on pegboards without wiggle? Heck yeah! This model uses my locking pegboard mount system for 1" standard pegboards. Magnet holes (if present) are designed for 10mm diameter, 3mm thick…
This tape measure holder (or shallow dish if you prefer to use it for something else) prints without supports (make sure your bridging settings are dialed in!). Uses two board attachments. This model uses my locking pegboard mount system…
This small hook - split into two interlocking parts for optimal orientation and strength - will hold just about anything with a hole in it. Print with plenty of perimeters and use a brim if you really need to (not required). This model…
A pegboard hook for hanging impact-style safety glasses. This model uses my locking pegboard mount system for 1" standard pegboards. Magnet holes (if present) are designed for 10mm diameter, 3mm thick magnets. “Board Attachment” parts are…
The 1x3 can be tiled horizontally! The others do not line up. I use a hammer and this jig to insert the magnets. Without glue, you can retrieve the magnets by poking them out through the bottom. Check out Sy's Peglock - Locking Pegboard…
This is a tape holder that is compatible with Sy's Peglock - Locking Pegboard System . It's designed to be used with 3/8" dowel rods. Inspired by this model . Printing Instructions Rafts: No Supports: No Resolution: 0.28 Infill: 15% Wall…
A magnetic mount for securely holding Workpro needle nose pliers (or other medium size pliers with a taper). This model uses my locking pegboard mount system for 1" standard pegboards. Magnet holes (if present) are designed for 10mm…
Holder for spray paint can on a pegboard using the Sys's peglock system. I included 2 pegs on the build plate, but you can remove them or change them for the pegs that work for you. Go see Sys's Peglock :…
Sy was nice enough to provide the .f3d file for his amazing pegboard system . However, judging from the comments on that model, it seems that some people are still resorting to scaling the entire model rather than adjusting the relevant…
I bought 4 different types of pegboard for my garage. Some had ¼ holes and some had 15/64 inch holes. All spaced 1 inch apart. Sy's peglock would not fit in the smaller holes so I used his fusion file and reduced the pegs from 6mm to 5mm……
This is a remix of @ntressler7's excellent Peglock Board Attachment - Parametric Template , which was a remix of @SyberSpace's excellent Sy's Peglock - Locking Pegboard System . The triangular wedge shape is mostly unchanged and will work…
This small curved hook - split into two interlocking parts for optimal orientation and strength - is modified from the original to better hold tools or other large parts above it. The base part is identical to that from the Thin Hook…
A simple storage bin that attaches to a pegboard with Sy's Peglock system. Requires one pegboard attachment. 2 Sizes (external dimensions): 120mm W x 42mm H x 80mm D 120mm W x 42mm H x 50mm D Internal dimensions are -4mm in width and…
I have become a tad bit obsessed with this peglock system, and made myself a solid body to boolean subtract from any model in order to use the universal board attachment. Add this STEP file body into any model, use a subtract/remove…
A hook with magnet above that connects to pegboards. Should work for many designs of snippers and pliers, but I designed it for Kobalt brand small wire snippers. This model uses my locking pegboard mount system for 1" standard pegboards.…
A tape holder for the sy's peglock available in 3 different sizes (30mm, 40mm, 50mm)
Holds a hammer, remixed from citizen458931's hammer mount but adds some extra supports and a front lip to ensure the hammer doesn't fall. My hammer is pretty high up and near my printer, so wanted to make sure this was extra safe. Uses…
Sliced in Bambu Studio. Printed at 15% gyroid infill on Bambu Lab A1 using default profiles for printer & PLA High speed. Printed at full speed. Thanks to Stellasfun for the amazing Sy's Peglock - Locking Pegboard System and Gherkin for…
Holds a hammer. I printed at .3 layer height fine. You can go lower if you wanted smoother curves.
The diameter of the hooks, angle of the top hook, and lengths of the hooks are slightly altered to fit 1" pegboards better; specifically the Harbor Freight 48" workbench and generic metal pegboards on Amazon. It maintains the original 1"…
A magnetic mount for small “yellow” needle nose pliers. This model uses my locking pegboard mount system for 1" standard pegboards. Magnet holes (if present) are designed for 10mm diameter, 3mm thick magnets. “Board Attachment” parts are…
A lightly angled mount made to fit a Kobalt brand folding imperial hex key set. Likely to fit any similarly sized tool. Base of holding area is 22mm deep and 40mm wide. Should hold items up to 120mm tall before they do not rest properly…
Remix of the hammer holder. Holds a mallet. Utilises Sy's Peglock System Print Settings Printer brand: Creality Printer: Ender 5 pro (stock) Rafts: No Supports: No Resolution: 0.2mm Infill: 50% but choose what you want. Material: eSun PLA+
These are some handy versions of Sy's Peglock template plate that make remixing easier and more flexible. I derived it from their original .stl so hopefully I got all the features correct. Same print instructions: 3 perimeters and ≤0.3 mm…
Changed my design to use the Sy's peglock system which is better pegs and more modular
I really liked the design of the original, but it's a little too big for my tastes. I would have liked to make all the surfaces thinner but I lack the CAD skills, so I just removed a bunch of the back plate. Little faster printing and…
A staple gun holder for pegboards using Sy's Peglock system. This model uses my locking pegboard mount system for 1" standard pegboards. Magnet holes (if present) are designed for 10mm diameter, 3mm thick magnets. “Board Attachment” parts…
remix of a clamp holder for pegboard using the sy's peglock system. I used labrats subtract model. unknown if this works or not. My first print failed. I'll try again this week. shouldnt need support Ok I printed it in abs. Worked as…
Print Settings Printer brand: Creality Printer: Ender 5 pro (stock) Rafts: No Supports: No Resolution: 0.2mm Infill: 30% but choose what you want. Material: eSun PLA+
Inspired by the "One-handed removable paper roll holder kitchen wipe tissues" from Barebaric, I designed my version to work with "Sy's Peglock - Locking Pegboard System", a 25mm pegboard and a roll length of 260mm. For the assembly, 4…
I only know Tinkercad (for now) so I used that to mash the following two awesome models together: Dewalt Power Tool Skadis Sy's Peglock Locking Pegboard System I don't own the Skadis - I have a more typical pegboard in my workshop - and…
A 125mm angle grinder mount that uses Sy's Peglock system. (Printed without supports)
This holds standard 68mm diameter cans for WD-40 products. The cutout's inner diameter is 69mm, for a loose fit, and is only 17mm deep. This minimizes the vertical clearance required to insert or remove a can.
A small shelf, and a set of small bins designed to work with Sy's Peglock system - sized for hobby and craft supplies. Simple, sturdy, efficient, and no supports required.
After running into this pegboard system: https://www.printables.com/model/249871-sys-peglock-locking-pegboard-system/files I had to create some new variations in cad to hold some of my woodworking tools. So I decided to make a holder for…
This is a negative body of Sy's Peglock Plate. It can be used to be subtracted from your model, to get a perfect cut-out for Sy's Peglock Board Attachment. It also has a protruding block in order to allow the template to be positionied…
Just a simple adaption. When you think it's fully seated - press it firmly and it will click into place.
PegLock system by Sy's. This is a remix to hold the Zicron L50 stud finder. This is a nice fit with a slight squeeze at the bottom to hold the tool in place. https://www.zircon.com/tools/studsensor-l50/ Print Detials: VoxelPLA .25 mm…
This two part mounting plate glues to a Tekton metric Allen key set and provides magnetic mounting to a pegboard. I used 6 magnets - 2 in the Allen key side and 4 in the pegboard side. This model uses my locking pegboard mount system for…
Adapted Eltord's LTT Screwdriver Hanger to work with Sy's Peglock. Requires "Board Attachment (Universal)" from “Sy's Peglock - Locking Pegboard System.”
Remix for the Sunlu S2 mount but for a 1" pegboard using the absolutely fantastic Sy's Peglock System. Also have added a small recess for an air gap spacer if needed Optional screw holes have been added on the bottom. The feet of the S2…
Simple medium shelf. Dimensions W:85mm, D:65mm. Prints with no supports. Works well with PLA and PETG. If this was in a hot garage I recommend PETG which will hold up better to high temperatures. Additional necessary components You also…
Two sizes: 68mm diameter 58mm diameter Uses Sy's Peglock system: https://www.printables.com/model/249871-sys-peglock-locking-pegboard-system
This is a Sy's Peglock compatible holder for a Milwaukee Fastback model 48-22-1903 knife (this is the larger/thicker fastback that has extra blade storage). There are two STLs, one holds the knife with the clip facing the back and the…
As Jacob says in his description: This is the inch version of the rail. Sy is a genius and kaje's screwdriver holder is fantastic. Simple. Works. Genius. The screwdriver works so much better than other solutions where your screwdrivers…
This is loosely based on Sy's Peglock - Large Hook but parametric so you can create a wide variety of hook lengths and shapes to suit different tools. It can be used with my Sy's Peglock Improved and Parametric pegboard attachment or Sy's…
I needed to hang spray cans from my pegboard lower then where the pegboard ended. so i added a second spray can cup under the original one. And made it using the Sy's Peglock system since it's the best one i've found for pegboards.
A Milwaukee M18 battery mount that uses Sy's Peglock system. (Printed without supports)
This Board Attachment needs less depth and can therefor be used with Pegboards mounted closer to the wall. It uses nearly the same depth as the metal ones shipped with my Pegboard.
I optimised this for the Pinnacle metal pegboards from Bunnings. They are a tight fit, but just right as far as I thought. These are the specific settings (from @Donovan Baarda's parametric setup) Body Width - 6mm Pegboard Thickness -…
Added Sy's peglock to Jef's battery holder. Fits the high power hp 4ah and 4ah lithium standard battery updated 8-11-2023
Holds 5 chisels using Sy's peglock mounting system. Fitted for Narex Richters and mortising chisels but should fit other chisels as well V2 Is thicker since V1 seems to be bending after long term use
Print with supports for the holder overhang.
After running into this pegboard system: https://www.printables.com/model/249871-sys-peglock-locking-pegboard-system/files I had to create some new variations in cad to hold some of my woodworking tools. So I decided to make a holder for…
This Sy's Peglock compatible tape measure holder can be customized to fit your tape measure, open the .3mf file in Fusion and go to Modify > Change Parameters to set the length and width of the tray. The linked 3mf file is a smaller size…
single peg or double peg plate, if you use the double peg, I recommend only using the ‘flat’ peg for Sy’s peglock hook on the bottom one, not the curved peg, to provide rotational support.
Remix of ari.mandjelikian's model to fit the DCB107 model, as it's hole spacing is 4" instead of 4.5" Sy's Peglock System compatible mount for DeWalt 12v/20v battery charger DCB107.
This is vaguely similar to Sy's Peglock - Screwdriver but parametric so you can create a wide variety of loop sizes and shapes to suit different tools. It can be used with my Sy's Peglock - Parametric Pegboard Attachment or Sy's Peglock -…
See Sy's Excellent Peglock System for more great options. Printer: Bambu Labs P1P Filament: 1.75 Elegoo PLA+ Light Grey Slicer: Orca Nozzle: .4 Quality: .2 Suppot: None Infill: 15% Time: 2hrs 5mins
This is a better version of my Dewalt battery mount for pegboard using Sy's peglock system. the batteries don't latch, so it's an easy one handed operation. Made a single and double battery mount. Included are peglocks that work for me,…
I really liked Sy's Peglock system, but was tired of scratching and hurting my hands trying to remove the board attachment. I don't mind a little wiggle room, and I don't need my mounts to be so sturdy that I can't move them. So, I scaled…
Created in Orca Slicer and exported as a generic 3MF file. Includes Metric and SAE models, as well as the require Peglock board attachment pieces. You can remove and modify models as you wish in your slicer. If you have a pegboard other…
I love the Sy's leglock system. I could not find the shelves I wanted. So I made them and love them! They are strong. They have a lip on the front to keep items in place and can hold various items. I created three versions: A small one (…
After running into this pegboard system: https://www.printables.com/model/249871-sys-peglock-locking-pegboard-system/files I had to create some new variations in cad to hold some of my woodworking tools. So I decided to make a holder for…
Printer: Ender 3 V1 + Hemera direct V6 hotend Filament: 1.75 Elegoo PLA+ Light Grey Slicer: Orca Nozzle: .4 Quality: .2 Suppot: None Infill: 30% Rectinlinear See Sy's Excellent Peglock System for peg options.
Simple and sturdy bin. Internal dimensions W:80mm, D:80mm, H: 80mm. Prints with no supports. Additional necessary components You also need to print the right “peg” for your particular pegboard. I include the file for a typical “Home…
3D Printed Peglock version of a standard pegboard mount that I used to mount my drills. Requires supports to print. Compatible with 1" pegboard. Two models are included, the drillholderasm.stl should work with most green Makita tools. The…
This is a remix of my Sy's Peglock - Improved and Parametric model that was a remix of @ntressler7's excellent Peglock Board Attachment - Parametric Template which was a remix of @SyberSpace's excellent Sy's Peglock - Locking Pegboard…
Dewalt battery pegboard mount using Sy's pegboard system
This is a peglock piece adapter for snap fit on metal pegboards. Printed with .6 nozzle at .2 layer height using PETG.
I modified Sy's original design to work with Ikea Skadis pegboards
I made this for the needle nose pliers that came with the Prusa MK4. This model relies on the spring force of the pliers to stay in place. I wanted something like…
This holds 2 rafter squares side by side and mounted using Sy's Peglock system
Made to hold an Ames Infrared Thermometer using Sy's Peglock system.
If you've already got a pegboard, mounting this version is cake! Print flat with tree supports. Use a flat head screwdriver to wedge in and peal out the bottom, then slide it into the top of the peglock slot and twist and it should all…
A Makita 18v battery mount that uses Sy's Peglock system. (Printed without supports)
This peglock is Sy's design which I have modified to fit the RACK IT system metal pegboard from Bunnings. I have also adjust it so it will slide into the attachments a little easier but still somewhat snug. Edit: All tested and works…
Remix of middleagedspread's rafter holder. Made gaps wider to accommodate thicker rafters. Utilises Sy's Peglock System Print Settings Printer brand: Creality Printer: Ender 5 pro (stock) Rafts: No Supports: No Resolution: 0.2mm Infill:…
Remix of the disposable glove dispenser to work with Peglock on a 1" pegboard. Printed with supports.
sy's peglock AA and AAA battery holder easy print. prints in 2 pieces you need to super glue together. No supports required. My AA did not turn out amazing because I did it in abs and it warped slightly. I am gonna try petg next. My…
I designed this to hold a few mini pliers that I had kicking around. OnShape Document:…
A while ago I made a holder for 2 of the Ryobi 4v batteries, Rotary Tool and Driver . It worked well, and has a few makes, but I was never very happy with the aesthetics. So I set about making holders for the batteries and each of the…
A handy way to hang your gloves on your pegboard when using Sy's Peglock system. (I printed with 4 walls to help the clip strength)
This is pegboard hex key storage for use with Sy's peglock pegs. It uses minimal pegboard space. Left and right are mirror images, and can be used together or separately and you can pick which to store either metric or SAE in either.…
PLA+ 2 walls 15% infill No supports Slow speeds and cooling for bridges
38mm sized for small dropper bottle 52mm sized for vallejo or craftsman, paint, primer, and airbrush liquids 65mm sized for golden or Medea air brush meterials 75mm sized for eisco chemical bottle
Modified the original to use Sy's Peglock system. It uses the same peglock included with the system here: https://www.printables.com/model/249871-sys-peglock-locking-pegboard-system This was specifically designed for 1in pegboards... but…
version 1. Initial Release. Designed in TinkerCad. Print Detail: VoxelPLA 0.25 Layer Height 0.40 nozzle 10% In Fill
A mount for adjustable (locking? offset?) pliers
This is a slight remix of @WDNick's Stanley Tape Measure Holder. It is a little longer and wider to accommodate the larger size of the MaxSteel tape measure. It uses the peglock type clips which you can easily find by searching. I used…
This model adds Peglock compatibility to the iFixit Pro Tech Toolkit holder originally designed by @toxvrd. Mount it by placing two Board Attachments on your pegboard with one empty hole between them. The attachment plates on the back of…
I have been using an early version of this with wood pegboard pegs for years but it didn't fit my new metal pegboard. Then I discoved Sy's peglock system which allows for anyone to find or make pegs for their particular pegboard and…
In my short experience with Sy's Peglock System, I have found that things that don't have a contact surface high enough above the hook attachment can be knocked loose if rotated up. Extending that area a bit prevents it from rotating…
A Sy's peglock-based holder for @K-Studio.ca 's microfiber bed cleaner . Make sure to also print a peglock pegboard mount , or generate a custom sized one.
A pegboard holder for the Franklin Sensor M90 stud finder, using the Sy Peglock system
Holder for Super Lube grease (3 oz) and oil (4 oz), compatible with standard 1" x ¼" hole pegboard. This uses Sy's Peglock System: Print Board Attachment (Universal).stl in PETG for best strength. Fold over and insert into the pegboard.…
V2 is a more durable version designed to be printed on its side so it has long strands running the full length. This is a storage mount for a DeWalt/Craftsman tough case. Simply push the case up into the top lip and set it down on the…
This is a shelf for pegboards for people using the syspeglock system. It should print with no supports. My Bambu with PLA doesn't have any pealing up from the bed but this is large and flat so if you have issues you may need a brim or…
