Liczymy pasujące modele…
I've designed two different print in place support free axle benders for pinewood derby cars. They are used to bend standard axles, 0.087 inches in diameter by 1 inch long. One is a hardware free version that bends a single angle ~ 3…
A recreation of the BSA Pinewood derby wheel for printing or use in car mockups
This is a spoiler that may be glued to a pinewood derby, or similarly sized, car. Category: Vehicles
3D print tools to dominate the competition at Pinewood Derby! Almost all the models can be printed from PLA, 0.2mm layer height. The inner and outer wheel chucks contains a 3D printed flexure, and would benefit from printing from PETG.…
These are the Pinewood Derby Cars from my two sons in 2020. They started with my boys making hand sketches showing what they wanted. My oldest wanted a batman themed car, and my youngest… he wanted shark car. We sat down in my office and…
I created this model in Blender for a family Christmas activity and it was a big hit! Everyone got their own car and we built a regulation pinewood derby track to run them on. Unfortunately, the cars themselves are not regulation, since…
Simple print for a trailing or leading fender for standard BSA Pinewood Derby Wheels. Inside Wheel air shields are formatted for both a standard flat front disc as well as a weighted rear wheel disc sized to fit standard 3/8" tungsten…
-A trophy that lets scouts display their winning car. -Print your own placards and customize however you wish. -Print the pieces and glue together.
This is a remix (link below) The holes are slightly smaller than a 3/8 bit depending on your printer settings, you can print with additional perimeters and drill through using a 3/8" bit (it will bite slightly into the plastic but should…
This is for drilling axles at a 3 degree angle using a drill press (or a handheld drill with a 2-axis bubble level). It is not meant to locate the holes, just hold the unmodified BSA block for the car at an angle. Why 3 degrees? I used…
These are some chucks to hold the inner and outer portion of a standard pinewood derby wheel for tuning purposes. They fit standard drill chucks, remember to use low speeds when polishing. The derby wheels I used have the following…
When your seven-year-old son asks "Daddy, can you print me pinewood derby wheels?" there is only one correct answer, and it isn't "no". This wheel was designed using drawings of the actual wheels and should be dimensionally accurate.…
This is a 3d-printable minecraft sword car. My son is making his "wood" car based on minecraft so I designed this sword to go with it. It is not "legal" dimensions so it is only suited for outlaw class (and this version is not properly…
The mount is sized to fit the length/width of a pinewood derby wood block, so most pinewood derby cars will fit neatly inside. Please remix this if you have a custom length/width for your car. The display stand features a recessed text…
This 3D-printed model race car meets a Pinewood Derby car's size and weight restrictions. This car, of course, is not made of wood and therefore isn't legal in a traditional Pinewood Derby. It might be a fun entry into an “Outlaw Class”…
This is an axle angle gauge for measuring the angle of pinewood derby axles after bending. This gauge is setup for bends ~0.375in from the head of the nail. Print Settings Material: PLA Nozzle Size: 0.4mm Layer Height: 0.2mm Perimeters: 2…
The curvature of the track is a 24" radius - much sharper than the official 96" radius - but this way it'll fit on a Prusa XL, or any 200mm printer in two pieces. This ramp is intended for home testing of pinewood derby cars - it matches…
This is a pinewood car display. It is designed so that actual Pinewood car tops the trophy. This is a 5 part design that prints in 4 prints. I used gold PLA for the base and stand, silver for the hub and black and white for the tire. This…
This model is designed to complement a standard BSA Pinewood Derby kit. Pinewood block should be resawed from 1.25" to 0.25" thick. 1.375" should be removed from the “front” of the block with a crosscut. The “front” has a gap of 1.78"…
P.E.R.C.E.I.V.E. - Pinewood dERby Car mEasurIng deVicE This is a simple yet accurate tool for your boy or girl scout to measure their pinewood derby cars. It is sized for U.S. Pinewood Derby regulation. This has slots that require 1/16"…
If you'd like to build a fast Pinewood Derby car, one option is to build what's known as a “Rail Rider”. The car is built so that 3 wheels make contact with the track, and the 4th (a front wheel) is installed higher up on the car so that…
Rough model of a pinewood derby track I plan to build from 1/4" MDF. Loosely following this guide: http://www.waynesthisandthat.com/pinewoodderbytrack Track should be easily disassemble-able into approx. 4-ft long sections, to allow for…
This is a slightly stylized version of the Batmobile from the classic Batman the Animated Series cartoon. Its my entry into the 2023 East Coast Rep Rap Festival SHOW CAR class. I originally designed from online blueprints I found online…
Optimized to print well in batches on an FFF-style printer without post-processing. Note the use of sequential printing mode, which avoids inter-wheel strings and the associated surface defects. Also note the use of the ‘Archimedean…
This is a fast, unique, standard sized pinewood derby model toy car body. Print it with supports to get the best wheel well shape. Using the standard pinewood derby kit parts (or equivalent), lightly hammer in the nails to install the…
I haven't printed these yet, I designed them to dimensions I found online. I tried to make them "printable"... I plan to use them for a car I will 3d-print for the outlaw division to show kids what a 3d printer can do. I just printed…
This is a miter box jig to hold derby axles that allows a groove to be scored in the nail heads using a hack saw. The is no hardware needed as the clamping force is provided by the user as they grip the handle. To release the axles the…
I printed about 50 of these, with a total filament/material cost of just over $100. This will save our Pack several hundred dollars a year. Get started early as it can take a few weeks to print them all. Any tips received for the model go…
Pollymaker PollyTerra PLA Silk Gold/Silver/Bronze 210/60 Navy Blue, Black 190/50 All wings were printed with a brim that was removed post printing, this allowed for sharp edges and points as well as helped with adhesion. Wood bases are…
Just a really cool pinewood derby car with a tool box thing to add for weight.
A custom-designed organizer for pinewood derby cars. Holds up to 4 cars by itself, with depressions on the shelves to keep the wheels in place. It is designed with bumps and depressions on the very top and bottom to be stackable as well,…
1:25.4 scale model of my pinewood derby track
I designed this for a friend who was asking me for a pinewood theme to build with his daughter. They both instantly loved the idea. The pictures are courtesy of his project!
This is designed to hold a cub scout pinewood derby block still in a miter saw. The two halves are the same but you need two of these. If you put them together one way, it gives the 10 degree angle you need to cut the block into a wedge.…
While looking for a Pinewood Derby Track to make for our Cub Scout pack we found the www.nerdyderby.com track design which was very modern and a clever design to be made in a home workshop from plywood. The Nerdy Derby track files are…
Over twenty years ago, my dad helped me make a pinewood derby car. It quickly became one of my favorite toys, and I still have it today! It's definitely taken a beating over the years, since it went to college with me and (somehow)…
Requires two M3x30 (or 35) bolts and hex nuts and whatever hardware you want to use for attaching the dial indicator. Snug down on the pin just until it stays put but don't crank it down. Options for the pin that the wheel rides on: I…
I purchased an official BSA Pinewood Derby kit. The box indicates the copyright is 2018. These models are my measurements of the official parts. It should help people decide where/how to modify their parts. Category: Vehicles
Designed this for my pinewood derby car. Blower flap was quickly designed in prusa slicer. I'd recommend making the flaps cylinders slightly narrower to turn more smoothly in the blower. The cab fits perfectly on top off the window print.
Took the great design by mcarson74 and adjusted the model to hopefully make it run faster. Cleaned up the fenders so the wheel won't rub on the inside of the fender and hallowed out the top to accommodate weight blocks. May need to carve…
Printed vertical
Trophies that I made for my child's Pinewood Derby competition. There are 5 pre-designed trophies to choose from and 3 blank trophie. Assembly: Print 1 Tire Topper, 1 Pillar Topper, and 1 Trophy. Tire topper slots into the pillar topper…
These are fenders for your pinewood derby car. Cut your block of wood, install the wheels and super glue these to your car, being careful to make sure there's enough room for the wheels to spin freely. Enjoy!
I designed this simple “pinewood” derby car with angeled axle holes as described in Mark Rober's video: You shouldn't have to bend the axles. If the holes are too small when printed, be careful when drilling them out so as not to change…
Pinewood Derby Car Stand I made this stand to showcase my son's champion pinewood derby car. The car already had a 1/8" hole drilled into the underside use for painting. So I simply fashioned a pin on the mount to hold the car to the…
Created from this page, originally found on Pinterest via Google. http://web.archive.org/web/20100212060041/http:/www.scoutingthenet.com/pinewood/ Category: Hobby
I asked my son what he wanted his Pinewood Derby car to look like and his mom had bought him some of the lights already, so he said he wanted a firetruck. Well I leaned into it and designed a ladder and some fenders. The fenders didn't…
Check your local rules to see if balancing can be done, or if there are restrictions on how to balance (such as adding or removing mass). The fixture will require the following additional hardware: Qty 2 - M5 hex nut 16mm or longer M5…
A basic pinewood derby car with 3D printed cosmetics All wood working is simple as the base of the car is just a wedge. once you cut out the wedge paint it and glue/epoxy on the 3d printed parts Drill guide is used to drill out a cavity…
I made this simple box to confirm the length and width of a Pinewood Derby car. If the car fits inside of the box it should be a legal car.
This car is potentially really fast print and racer for your next pinewood derby. Won third place and looks good too. Use paints for most awesomeness!
Wanted to design my own Pinewood Derby Trophies, two different styles within the file. The base may need to be adjusted.
Simple puzzle piece like wheel chocks for your Pinewood Derby.
Here is a decorative arrow for Pinewood Derby car. Design is similar to Arrow Of Light but not exact. I printed “DO YOUR BEST” separately and super glued to the arrow. The arrow stem is hollow to allow for additional weight if needed. The…
Our pack had an "outlaw" class with no restrictions on wheels for the pinewood derby. Mine performed well except it wobbled due to the "axle" offset in the wheel. I had added the axle to give room to angle the axles. The version uploaded…
Pinewood derby cars are a right of passage for Cub Scouts / Scouting troops everywhere! While you can hack at a derby kit, ask your scoutmaster about printing a car body instead! This design looks great and will be fun to carve or print!…
Scanned from diecast toy and scaled / trimmed to fit on modified pinewood block from BSA Kit. I trimmed the block height by ~10mm and the length by ~15 to keep in size requirements. Printed with a low layer height (~.1) and slim tree…
I wanted a jig for installing 3/8 weights. There are options for one that locks into the axle for safe spacing without splitting the axle groove. There is also a no axle option that can be slid anywhere. This is designed for a standard,…
I'm uploading the fusion 360 file and .svg files so that they can be customized to your pack. It should be as simple as editing the sketch with text on it. I was working on a set of trophies, but life got in the way and the race got moved…
There are a lot of great pinewood derby display stands out there, but I couldn't find one that did everything I wanted. Either the angle was off or it was flat, or it required some type of support on the base of the car, which depending…
This is a replica model of a Boy Scouts Pinewood Derby Racer. It wheelbase and size will meet most stock class derby rules. There is a slot in the bottom for adding lead weights if needed.
I cannot remember where I got the wheel and sparkplug 3d files from (my apologies if you are the original artist) but I altered them to make this stand. Print at .15mm, with supports and you should be good to go. I added the year to mine…
I created this model to meet the size requirements for a pinewood derby car. "I did it not to compete but to show the potential of 3D printed design to our scouts. The model is designed to snap together and have weights and lights stored…
Fenders for pinewood derby
Made this pinewood derby car based upon a violin. Print instructions Category: Vehicles Instructions My son and I made this. He started the design in 123d and inkscape and then we moved it into viacad for the final version. First we…
Transform your collection of Pinewood Derby cars into a stunning wall-mounted display with this miniature display mount. Showcase your most prized cars and relive the memories of your victories every time you look at them. With its sleek…
Print two, hang, display. Use the cleat model for a ¾" French cleat wall like in the picture. Use the wall version with a screw for any flat surface. If you want to reduce it to a single car, use your slicer to create a cut.
My son's cub scout troop needed trophies for their pinewood derby. I found these awesome trophies for first, second, and third place... WHEEL TROPHY FOR (SLOT) CAR but we needed one for best in show, so I did my first real attempt at a…
I began to have Pinewood Derby cars piling up on my shelf. So i thought what better way to clear the space and display them as Art then to hand the cars on the wall . I printed this with 15% infill, no supports, and .2 layer height.
Or Could be considered a Cyber Truck Made to fit official pinewood derby wheels linked below The Hole on top is to weigh the car down its 1 inch in Diameter Quarters Fit perfectly. This was the very first model I have designed myself!…
Pinewood Derby car stand showcasing 3 cars. Print some for your pack and use as a fundraiser, they're popular! I print mine in a dark blue with a yellow strip and the pack number along the bottom, looks pretty nice.
This year we wanted to make a pinewood derby car that looked like a Lamborghini Police car (POLIZIA). What's a police car without a lightbar. Built a small circuit using 555 timer chip and 2 Blue LED's. We needed a lighter to make the…
This is a base for our Packs Pinewood Derby trophies. The holes are sized so that any spark plug will fit.
Pinewood Derby Submission
Printed this kit for my son's pinewood derby car, he didn't want a boring flat race car. Big thanks to the people that modeled the original sources, I just chopped things apart to get the individual parts that he wanted. I made the water…
A stand to hold a Pinewood Derby car. This stand holds the wheels slightly elevated so the cars will not roll when being staged for a race. Designed to be printed with a resin printer.
My pack needed a quick jig for checking Pinewood Derby car compliance. Specifically, we wanted to validate width , length , and track clearance . Here's a jig that'll help you perform these checks! Printing information: I used a 10%…
Originally made for our Cub Scout pack so every Scout got an award for building their Pinewood Derby car. Each den has their own set of coins. I have been asked to update each year. I have made these generic so they can be used by any Pack.
Made this pinewood derby car based upon a violin. Instructions My son and I made this. He started the design in 123d and inkscape and then we moved it into viacad for the final version. First we decided how to cut the block of wood and I…
A gun from the game Pinewood Builders Computer Core. First Model I have made so its not that good. I havent tested it yet possibly not symmetrical I don't know
I designed these Pinewood Derby medals for our Pack because purchasing awards can be pretty expensive, but filament is cheap. I added text to the center of the medal in the slicer. The medal was designed in Fusion 360. Edit Sketch2 in the…
Remixed from mcarson74's well-designed pinewood-interpretation of Back to the Future: https://www.thingiverse.com/thing:1229317 Minor changes. The Mr Fusion detail-piece was a bit corrupt, so I reworked that one from scratch. Also…
This is a BSA compliant body for a pinewood derby car. In order to use the body, you will have to trim down the pinewood block that comes with the kit. To attach it to the chassis, I recommend driving a screw through the pine block and…
This years pinewood derby entry. Designed to be a penguin sliding down the track on his back. The idea and design is inspired from the penguins in a recent animated movie, but not really any specific character. The wood block is cut in a…
This is the set of award coins for the Cub Scouts Pinewood Derby for 2025. There are coins for 1st through 6th place for each of the ranks - Lion, Tiger, Bear, Wolf, WEBELOS, and AOL. The .3mf file was created in BambuStudio.
Our pack now allows 3D printed cars to compete against the standard pinewood cars. Fortunately our standard car came together in time. If it hadn't, this would have been "Plan-B" Category: Hobby
Mount your pinewood derby car on a vertical surface with either the drilled or wheel hook mount. No supports are required for the print. Both use #6 or #8 screws with various head styles. Drilled Mount The top of the model has two flat…
Pinewood Derby Car Storage Shelf Display Show off those speed machines like the champions they are. This Pinewood Derby Car Storage Shelf Display turns race-day memories into a clean, eye-catching showcase. Designed to securely cradle…
model of a pinewood derby dragster doesn't move sorry
This was an adult race car (we have a separate race for parents/siblings) I entered in my last Pinewood Derby for my Cub Scout Pack. It was made to celebrate a bet I lost to my pack and had to color my long beard, which I had grown for…
Cars go inside and if they fit then they meet the requirements to race. This box is based on these requirements. I suggest printing in something a little translucent.
This makes a ladder shaped pinewood car that actually articulates. You can set it up as a ladder, or you can fold it down and race it. As designed, the platform is captive to ladder face. If you go to 3D print this, watch our for that.…
Award coins for the 2026 Pinewood derby season. Six places for each of the Cub Scout ranks. Both STL and 3MF files provided.
Wall mount (or desk stand) for Scout Pinewood Derby cars. Use plain or with a custom nameplate. This one works with the same name plate models as my Scout Pinewood Derby upright trophies , or make your own with a CNC or sticker machine.…
i made it look like chez i hope u print
Ich bin im Seifenkistenverband Baden-württemberg e. V. aktiv. Hier haben wir eine Rennklasse, die nennen wir Mini Seifenkisten Racer. Kurz: MiniSKR. Dazu gibt es auch eine Internetseite: www.miniskr.de www.seifenkistenverband-bw.de In den…
This is a 3D mockup of what will become the finished car. Category: Hobby
this is a sensor upgrade for the pine wood derby car set. i found that the sensor positioner was lose and unreliable. so i desiend a better fit. i tested it out and it worked perfectly
