Liczymy pasujące modele…
I created this model because I needed a method to keep a printhead pressed down continuously. I used PLA with nozzle temperature settings of 220 degrees Celsius and print bed temperature of 65 degrees Celsius. Layer height 0.20mm. Print…
Small tip to clip onto the end of a press tool for watch needles in place of the original tip. Printing Instructions: Recommended Settings: Use a layer height of 0.10 mm for an optimal balance between printing time and quality. Supports:…
Parts: 1x M12x330mm Gewindestange (Zweierpack für 2,99€) 2x M12 Muttern (Viererpack 1,49€) 2x Korrosseriescheibe 13x37mm (2 = 0,47€) 2x Karrosseriescheibe 17x50mm (2 = 1,49€) Gesamt: 6,76€ The diy-steuersatz-werkzeug (Headset Bearing Cup…
Zum andrücken der neuen Bremsscheibe, damit der Planschlag zuverlässig gemessen werden kann. Geeignet für Radnaben mit nicht durchgängigen Gewindebohrungen
Ein Buchblock aus losen Blättern im Format DIN A6 kann zwischen diesen Brettchen zum Verleimen eingespannt und gepresst werden. Durch die Aussparung zwischen den Standklötzchen kann der Buchrücken vor dem Verleimen eingeschnitten und…
Files for the compressed air engine used in the following project: FDM printed parts: Crank Case (Front, Rear) Crank Shaft Bottle Lid Engine Mount Piston Head Cap Resin printed parts: Cylinder Head Conrod Piston Seal Mold Other Required…
There are numerous designs out there of clips that secure the lid on IKEA Samla (Filament storage) boxes. But I could not find any that really presses the slightly overhanging lid onto the box to keep it as air tight as possible without a…
You don't have a compressor but want to remove dust, wood shavings or other light dirt from your workplace? No problem! With this attachment for your cordless screwdriver, it's done in no time at all! Is it hot and you need to cool down?…
This is amazing model was made by rndmframes_printing and the licensing allows sharing with attribution so I wanted to make sure the prusaprinters.org visitors didn't miss out on it by re-uploading! Original link here:…
The original model was impressive. The author vandragon_de has made a version without holes for bathtube use, but it has some missing solid geometry at the propellers, so that it won't be properly sliced(with CURA). so I fixed the issue.…
Category Part Quantity Fixings M5 Nut 6 Fixings M5 Washers 10 Fixings M3 x 10 CHS 10 Fixings M3 x 20 CHS 2 Fixings M3 Washer (optional) 8 Fixings M3 Nut 10 Fixings M3 x 8 CHS 1 Fixings M5 x 30 BHS 6 Fixings M5 x 8 BHS 10 Fixings M5 T Slot…
Burgerpresse mit 200Gramm-Markierung. Das Oberteil und der Griff bekommt je ein Gewindeteil und wird mit einem Gewindestift verschraubt und geklebt. Ich habe das spezifische Gewicht von Hackfleisch gegoogelt und den Durchmesser und die…
This modern designed bowl is like a cut pressed diamond. Minimalist, modern and timeless. 🚀 Support My Work & Supercharge Your Business & 3D Projects! 🧡 Join my Patreon and unlock 400+ premium 3D models – with new designs every week ! 🔧…
Burgerpresse XXL mit 200 / 250 / 300 Gramm-Markierung. Ich habe das spezifische Gewicht von Hackfleisch gegoogelt und den Durchmesser und die Dicke für genau 200 / 250 / 300 Gramm ermittelt. Der Durchmesser des Patty beträgt 140mm. Aus…
I present the spring loaded Coffee/Espresso tamper gadget: easily compact your coffee grind with your own assembled tamper apparatus to make your espresso with style! Available for 49 - 58 mm portafilters. The handle, spring holder and…
Many of the other no touching tools do not have any type of enclosure which we will touch it with our hands or clothes eventually. Even those with an enclosure, it is a separate enclosure so it is not as convenient. This design is…
Modified Zburns adapter to print without supports and with PTEG. I do not trust PLA for items like these that need to be more ridged. please use caution when Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports:…
Pretty straightforward. Three screws, strong, and support-free print. I needed a hanger for my compressed air hose that worked for the side of my shop cabinets, and this is what I came up with. It's low profile because I have limited…
Press for burger patties in 135mm size. Every minced meat shrinks when cooked on the grill or in the frying pan. Depending on the type of meat, fat content and water content, the meat can shrink by 10% to 30%. That's why the press here…
Display stand for souvenir pressed pennies (elongated coins). Will hold up to 24 coins in total. From left to right the display is designed to hold alternating horizontal / vertical coins (see photo for an example). Printed with 3 walls…
Molds to create rice-based deliciousness. (Onigiri & Musubi). The onigiri mold fits is designed for half of a sheet of nori and then the musubi mold will fit a slice of spam. NOTE!! Please ensure that you are using food-safe filaments (eg…
Da die Original Presse leider kaputt gegangen ist, habe ich eine ähnliche Presse konstuiert. Ich habe es mit PETG gedruckt. 0,2mm Schichthöhe 20% Infill
This is a new design of the venturi nozzle V04. If you tested the older version too, please tell me which is best. With this print you can upgrade your normal compressed air gun to a gun with a venturi nozzle. This design is for a…
To prevent spent primers jumping all over the place, you can insert these fillers into the slot of the ram of your RCBS press. Both have the same function, the T-shaped one comes out with the shell holder, the other one can stay in the…
Miniatures of all detectives and monsters from the add-ons suppressed memories and recurring nightmares miniatures. Mansions of Madness Second Edition — Recurring Nightmares: 8 detectives: Michael McGlen, Sister Mary, Gloria Goldberg,…
I take from https://www.thingiverse.com/thing:5783736
My mother, sister, niece do sew all and much. Ma asked me a while ago if I could do something like that. I could and she was happy. I just forgot to publish this little tool. It was only 1-2 years ago ;-) I printed this with a 0.4 mm…
Sewing machine presser foot for zippers. Print with sufficient detail in something that will give you good bridging and little stringing, optimised to need no supports. Keep in mind that the attachment bar is not metal so don't just drop…
Small and easy to print display stands for those nice souveniers. There is a version for horizontal and vertical coins. No supports needed. International names for those coins so everybody can find this: D/AT/CH: Quetschmünzen,…
2x2 Gridfinity block designed to hold a 10oz compressed air can and straw in any of the four corners. This block should also work for other spray paints, wd40, etc. Interested in Gridfinity?
Hi, this is a prototype of a vacuum robot gripper that creates its own vaccum using the venturi effect . It weighs around 6 g and can lift things up to 1.5 g (I just blew into the air intake) EDIT: @DickF tested it and was able to lift…
Benötigt werden: 3x Wanddübel für 4er oder 4,5er Spax-Schrauben 3x Schrauben M5x10mm mit Flachkopf 3x Muttern M5 2x Kabelbinder klein Muttern M5 von hinten in die Wandplatte einsetzen Schraubenlöcher bohren und Wandplatte befestigen…
fabrication d'une hélice suivant modèle de la pièce d'origine réaliser en PETG 1.75 blanc
Print this in gold, green/blue or pink to get RICH and annoy Mission control while you are at it! ROCK AND STONE!
a remix of the extended nerf barrel with a suppresser.
Mechnische Presse für das einpressen von Bauteilen. Das Modell wurde bis auf die Lager und Schrauben aus PLA gedruckt und getestet. Falls jemand den Hebel und die Achse aus Stahl fertigen möchte, gebe ich Fertigungszeichnungen hinzu.…
With this print you can upgrade your normal compressed air gun to a gun with a venturi nozzle. This design is for a compressed air gun with a diameter of 7,5 mm on the nozzle tip . For larger diameter you can change the scale in your…
Höhe: 150mm Breite/Tiefe: 84mm Modell muss verklebt werden ambesten mit UHU Allplast. Die obere Strebe erst verkleben nach dem der Boden eingelegt ist!!!! Gerüst Seitenteil habe ich mit Z 0.5 gedruckt damit überall Supports sind. Drucker:…
Runde Erdpresse zum erstellen von Anzuchtballen mit einem Durchmesser von 35mm und eine ungefähren Höhe von 35mm. Und passt somit in alle gängigen Anzuchtkästen und Mini-Gewächshäusern. Perfekt für die Anzucht des eigenen Gemüse oder…
Der 3D-gedruckte Tubenquetscher ist ein praktisches Werkzeug, das speziell dafür entwickelt wurde, Tuben wie Zahnpasta, Salben, Cremes oder Farben effizient und einfach zu entleeren. Durch sein cleveres Design ist er robust und langlebig…
PLEASE TEST THIS ITEM AND POST A MAKE OR COMMENT IF YOU FIND THIS THING USEFULL SO IT COULD BE MODIFIED IF NECESSARY LIKE SHARE COMMENT, it is important Description: This is intended to be a oil drum cap for pouring / pumping liquids with…
Summary The keypresser makes it possible to automatically press a key when it is moved onto the left or right side of the keyboard. This can, for example, prevent the computer from going into sleep mode and you remain permanently…
These are presser feet designed to fit many sewing machines for splicing pieces of line to create eyelets, especially useful for example in paragliding or kiting. I've designed around low and high shank machines that I own, namely Pfaff…
Pas de support. Remplissage 100 %. 0.15 mm. Prusament PETG Clear.
This mostly parametric tray was designed to complement AJ Briones' Gridfinity bin for the HOTO Compressed Air Capsule body . It holds all nozzles, the dust bin, and dust bin extension with brush. Printed with PolyTerra Charcoal Black PLA…
The HPA Thing! Firing demo: How it works: The HPA Thing is a semi automatic or fully automatic Nerf blaster that uses pressurized air from Paintball air tanks, using the Roboman Cosmic Nomad HPA dump tank ! The blaster is currently…
Support mural sur mesure pour presses Bessey Korpus : largeur identique à la presse pour les fixer cote à cote, léger pincement pour clipser les presses et leur éviter de basculer, légère ouverture pour guider la presse vers le fond du…
Für das pressen leckerer Bürger Pattys. Evntl. ist es notwendig die Schale und die Presse mit etwas Öl einzustreichen um ein ankleben zu verhindern. Am besten mit Lebensmittelechten PLA o. PETG und einen für Lebensmittel zugelassenen…
I needed to run some flexible compressed air hose around the wall of my shop, so I made these wall-mounted hangers. They are good for hose up to 17mm diameter (and maybe a bit bigger). These are not designed to take a lot of stress or…
I enlarged 3 of the holes for the attachments. 2 were very tight and would pull the holder off the pegboard. The inflator nozzle would not even fit in the original hole. I suspect there are multiple versions of the blower being sold…
Co-Ax Reloading Press fits Forster and Bonanza presses storage for the tools needed to work on machine also holds a small oil bottle, no supports needed can print at any print height u like, there are also place to put magnets when done…
Parfois, il est plus simple de concevoir une pièce qui correspond à son besoin que de chercher dans les milliers de modèles de la communauté… Voici donc une variante dans la presse à cadre du simple : quatre coins à imprimer, une ficelle,…
Thing to press the sticky edge of the Libre3 sensor back on. It helps to improve the adhesion of the sensor. Randandrücker für den Kleberand des Libre3-Sensors. Er hilft die Haftung des Sensors zu verbessern.
My wife has a Bernina 800 sewing machine with a lot of different "Presser feet", so I designed this 3d printable hanger so she has them organized and easily accessible. This hanger is for the "9mm" presser feet, which works on many…
I ran out of compressed air cans and ran upon a hand held air compressor. The price of the device was close to the current price for a can 6 pack. I decided to risk the purchase, given return guaranteed satisfaction. To my surprise the…
If you play games on PC, you will eventually come across this particular need to press a certain key on your keyboard for extensive amount of time. Yesterday I needed to press one key for 30 minutes to level up one of my skills, damn…
A minecraft chicken keycap that flaps its wings when pressed. The base of the keycap holds the wings in place, only allowing them to rotate when the button is pressed as the button drags the wing down with it. PLEASE PRINT THIS AT A LOW…
Start outfitting your figures with a proper shop with this drill press. Everything you need to make either a free-standing or a bench-mounted version is included. Print one of everything, except the axels- for those, just choose either…
Print in whatever you like (I prefer transparent materials for this). You'll have to provide a 1.5mm thick piece of wire and press it through the holes to give the foot holder something to hold onto.
This thing is five way distributor for vacuum or compressed air. It can be used for vacuum tensioning, airbrush or other air applications. I use the part for vacuum tensioning on my cnc machine. To finish the part jou need the following…
ALS LEIDENSCHAFTLICHER KRAFTSPORTLER BIN ICH BEIM TRAINING AUF DIE IDEE GEKOMMEN, EINE BEINPRESSE ALS BUCHSTÜTZE 💡 ZU MACHEN. VIDEO: Ab 1:50min. Filament: PLA Düse: 0,4mm Schichthöhe: 0,3mm
le presse dentifrice vous permet simplement de vidé le tube.
A freestanding/desktop Bernina presser foot cabinet that holds up to 10 small feet & compartments for 2 large feet.. Print with the front side up. Use the attached f3d file if you want to make adjustments. Compatible with the OEM Bernina…
This molding tool tries to give a nice rounded shape on the rice ball, instead of the edgy and pointy shape of other tools. Edit: Optimized the base a bit :) How to use it: Spread a sheet of cling film on the bottom part. Push the rice…
Less than 10 percent of people who download an item click the “like” button. Be the 10 percent. Click the “like” button and show your support. If you find this model useful, feel free to buy me a coffee . I love my Tile Mate Bluetooth…
Hey Guys, So since i wanted to lern a bit more cad I started this Projekt and i think it can also be useful for you. This tool will help you to melt the Threaded Inserts straight into place while holding the soldering Iron for you. If you…
Safety / distance disc for match airpistol
not a real remix but strongly inspired i have designed an adapter for a green adjustable soldering iron with which it can be used in the MICROMOT drill stand MB 200 as a press for heat set inserts. The soldering iron is available from…
makes the back of the g920 racing pedals flat so that if you have it up against a flat surface it doesn't rotate
Since on the commercial market can not be bought less than 16 euros each or only in a set with a water separator, here is the pressure of a union nut. Printed with PLA 100% filling.
Every been playing a game and couldn't be bothered holding down that button. Also can't be bothered with Macros? This is a great solution. The key-cap can sit over the top of the key and when you need it to stay down you just press and…
A little tool to help with opening doors and pressing buttons without touching them with your hands. Use the hook for door handles and the tip for buttons and switches. The loop at the end of the grip will fit on a key ring. Only takes…
Added a base you can print instead of mounting to wood. It's been fairly stable for me so far. Connect with M5x8 & T-nut
What it is An individual route for the quest of finding the best font for filament extrusion based 3D printing. A printed set of font cards also helps to find out which font might be the best for a project at hand and what quality is to…
Remixed Model with simple Stand to hold a filled TE-SG
Hi, still a 3D modelling noob but learning, I have here my take on the 2003 Clone Wars suppressed clone pistol. I have done my best to replicate the form of the animated blaster but with extra detailing for a more realistic style to use…
I created this model to replicate a part that was broken on my wife's willow 3.0 breast pumps. Now I get to be her hero and she can never call my 3d printer useless :) I printed this with the following settings: Filament: Inland PLA+…
Original art created by us, then we used Hueforge to create this 200x200 piece. Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm Filaments Used: PLA BambuLab Matte Charcoal PLA Polylite Natural PLA BambuLab…
I really like this 9mm flat fell presser foot made for Husqvarna Viking sewing machines. It makes a wider flat-fell seam than anything else I could find for my Bernina, but it doesn't fit Bernina machines. I designed this adapter to allow…
The “Small PP” (PowerPresser) can be placed under the Mac Mini M4 to make pressing the power button easier and possible without having to lift the Mac Mini. The unsymetric, rounded shape is on purpose, as it is supposed to tip towards the…
I've created a presser foot holder shank compatible with Husqvarna Viking sewing machines, including the Jade and Sapphire model lines. This 3D-printable design allows for easy attachment of presser feet and serves as a replacement part…
This is a Venturi vacuum and air multiplier.
REMIX off https://www.thingiverse.com/thing:3260204 The printing is not tested Category: 3D Printing Tests
Da die Schablone meiner alten Play-Doh Knete-Presse bereits ausgedient hat, meine Kinder allerdings noch gern mit dieser spielen, habe ich hier kurzerhand ein paar Schablonen selbst entworfen, die an das original angelehnt sind. Gedruckt…
If you have a Zerowater dispenser system, then you know this button for the tap. It's fine if you just want a small cup of water, but if you say, need to fill a 4L jug, your thumb is going to be numb by the end. This is where my Zerowater…
Réducteur pour installer un presse-étoupe de 20mm dans une boite de dérivation avec trou de 37mm. Pièce à imprimer 2 fois.
le Presse-tube Pour Dentifrice
Feuchter Schnee ist ideal zur Herstellung von Schneeherzen. Wenn Zweige von Bäumen und Sträuchern dazwischen gelegt werden “wachsen” Schneeherzen auf diesen ;-) Für die Montage des Gelenkbolzens ist eine Zylinderschraube M2x10 oder eine…
because glasses gave rounded faces, they don't make good contact with the rollers so increasing the presure helps. Inside the glass their is a wheel ( a Plastic Bearing 6200 10x30x9 from ali express ) with a TPU tire. It is connected to…
I made this, so that you can stop looking for the right suppresser! please make and comment, and request stuff from me!
This is a model of my design of a heat press insert press. I've included a fusion360 file because you will likely need to adjust the gap to fit snuggly on your soldering handle. I put some cut up heat shrink around the handle to give it…
Meine Idee: Hab nach einem Tubenhalter mit Presse zum vollständigen entleeren der alle Tuben (Alu, Plastik) entleeren kann, leider wie noch so oft nichts passendes gefunden. Also selber einen erstellen. Empfehlungen zum Drucken: Ich…
I hate sewing. I really hate sewing but my grandmother used to enjoy sewing up my work clothing that always ripped weekly from my abrasive warehouse job. Since my grandmother has passed, I decided to fix my own clothing since clothing…
An alternative to the difficult to find Jean-A-Ma-Jig this sewing aid fits under the presser foot when sewing over seams in thicker materials. This keeps the presser foot level which helps prevent skipped stitches and broken needles. This…
I could not find the right spacers for the Jo Presser - Threaded Insert Heat Press . But I do have a 3D printer… So why not make them. These spacers can be used for the Jo Presser = Threaded Insert Heat Press but if you can find some…
This was originally designed for students whom only have the use of one hand. This enables people with this disability (person with a limb difference) to remain independent when using a computer. The design works on all computers and…
uses compressed air and strategically placed pipes to drive pistons creating rotation on the crankshaft
