Liczymy pasujące modele…
This is a remix of Michael Fanta's original Gravity Spoolholder for MMU2S , which rolls the spool up a ramp while filament is being dispensed and takes up the slack when the filament is retracted by letting it roll back down the ramp.…
This is an auto rewind spool holder which relies on a friction/slip clutch for consistent tension, the spool is held tight on the hub. This is a low profile, easy to print, and hopefully improved version of the Auto-Rewind Spool Holders…
I absolutely love the auto-rewinding spool holders, but the only place I have to put them is on top of my Ikea Lack enclosure, which works great, until you want to open the lid. I designed these brackets to secure the spool holders to the…
All functions, including filament rewinding, are fully operational. This mod has no drawbacks. A small update. It may not be obvious, but in order to make the coils spin easily, wash the bearing bushings in any solvent (such as purified…
Kegel für eine 10mm Gewindestange z.B. zum umspulen von Filamentresten mit einem Akkuschrauber. Benötigt werden 2 Kegel (siehe Bilder) Schichthöhe: 0.24mm, PLA Infill: 25% Cubic je 4 Schichten (Wall, Top, Bottom) Durchmesser: ca. 52mm bis…
David Glaze reworked Michal Fanta's original Gravity Spoolholder for MMU2S , which rolls the spool up a ramp while filament is being dispensed and takes up the slack when the filament is retracted by letting it roll back down the ramp.…
As soon as I purchased a 3D printer, there was an immediate need for a reliable filament winder. At first, like many beginners, I was winding by hand. Then I tried to wind it on a stool, attaching a handle to the spool and shaking it.…
Hello, This s fairly simple spool holder using the autorewind spool bearing from here https://www.printables.com/model/1036478-autorewind-prusa-drybox-for-mmu-no-more-buffer-req You will need paint on support for the slit where the…
This reel was designed to manage the power cord on a fuel pump that I use at work. Wrapping the cord around a spool was a pain, not to mention the constantly tangled wires. I based this idea off of the little auto-rewinders that they use…
If you want, you can support my project on PayPal . I am very grateful for every small donate :) Thank you! Descpription: ….I used David Glaze 's Silent Auto-Rewinding Gravity Spoolholder (reworked Michal Fanta 's original Gravity…
This version of the top plate increases the space to pass swatches in the top plate and moves the position of the top open yarn hole. The old position caused the yarn to get hooked onto the wheel screws if the tension was a little lower.…
This is a remix of the rewinding spoolholder mounts for the COREBOXX Premium. I found the original spoolholder mounts held the spoolholders fairly loosely, and spools would wobble when the printer was running. Inspired by MIRE_19115's…
Infill 30% 4-6 perimeters Layer .2mm Jednoduché odstupňované kužely. Stoupání je 2x1mm, díky čemuž půjdou z cívky bez problému ven. Použít se dají klasické, nebo vratové šrouby. U vratového šroubu je výhoda tvarové aretace přímo na…
Auto rewinding filament spools using gravity to solve the backlash caused by fast-moving printhead Inspired by https://www.printables.com/model/10370-gravity-spoolholder-for-mmu2s
Simple double-cone tool that screws together from opposite sides of a filament spool to hold it for rewinding. Should fit most 1kg spools with 48-58 mm inner diameter and reasonable thickness, and most mini spools all the way down to 42…
I've always thought the Gravity Spoolholder by @MichalFanta was a great idea, but I was content with my regular spool holder. Then I saw @Steven_36896 's design and I thought it would be great to put that on the frame of my MK3S+ to save…
The author recommended buying a Lego wheel for this purpose. Link was useless, so designed and printed these. Modified the basic design, added a hollow cylinder, combined using NetFabb 2023, and uploaded the STL file to PrusaSlicer.…
Main Features It an auto-rewinder, negating the need for a buffer It's compact, designed specifically for use inside the Prusa Original Enclosure It's strong enough to handle full spool rolls It requires minimal extra hardware It only…
Overview I really liked the rewinding mechanism on the fs2026 dry box system , but didn't want to use so much filament to print out a new lid. I also already had a desiccant and hydrometer holder in the bottom of my cereal box containers,…
I needed a way to run filament from the spool holder directly into PTFE with use of a fitting so I added a raised mount to the front bar.
Adapter for rewinding aspool to bambulab spool no support needed sorry for my bad eng
Use two or three clips between the spool holders to securely connect them together. These clips click into place in the hexagonal pattern of the spool holder side panels. I highly recommend the Silent Auto-Rewinding Spoolholder , although…
Rewinding Spool Holder When I first saw Filamentalist (https://github.com/Carrot-collective/ERCF_v2/tree/master/Recommended_Options/Filamentalist_Rewinder/Filamentalist_Classic_Rewinder) working, it was magical. There was one big flaw in…
Hex wheel for Silent Auto-Rewinding Gravity Spoolholder :)
You need some extra (about 10cm) PTFE tube an a small screw to clamp the tube in the guide. I used 4mm outer diameter tube to add al litte braking, so that the printhead cannot push the filament backwards. This prevents the filament from…
This pin will allow you to use Silent Auto-Rewinding Gravity Spoolholder with 2kg spools and 1kg spools. You can find a base for the 2kg Spoolholder here https://www.printables.com/model/314515-gravity-spoolholder-2kg-version/files
"Well known" self-rewinding spool holders have longer axle than those used by MMU2/S ones (also employed in Lack Enclosure v2 5-spool stand). So we may shorten spool hub (and gave problems with some wider spools), use original stands from…
Axel adapted to use 2kg spool holder base with silent auto-rewinding spool brackets. Gravity Spoolholder 2kg Version
It is a mold for casting the tires for the silent car rewinder for the MMU To be needed 5x single nuts m3x4x5mm 5x M3x30 screws It is best injected into the hole with a syringe.
Block for cables with broken auto-rewinding on vacuum cleaners. Use to stop the cable from auto-rewinding when the stop mechanism is broken and the cable can not stay in extended position.
Petg 3 strati 25% riempimento
I was looking for a Star Trek spool to rewind off of cardboard spools. Prints in 2 pieces. I used PETG for strength. Feel free to remix and let me know what you come up with. This may need extra support between the rings.
This clip allows you to route a PTFE filament tube along the side of the auto-rewinding spoolholder. I highly recommend the Silent Auto-Rewinding Spoolholder , but this part works with the original version too.
This is an alternative filament guide design for rewinding gravity spool holders like this , this , or many of their derivatives , used in multi-material setups. It allows you to route your filament tubes through a shelve floor and also…
After a while the screw caps can get very tight, and if they are very close to the spool it is difficult to remove by hand. This wrench is deep to move the lever away from the spool.
------------------------------------------------ Update: New version with a planetary gearbox is now available: https://www.printables.com/model/1881205-dry-filament-spool-holder-with-nema-17-motor-and-p…
The motorized filament spool holder is designed to keep filament dry and, when combined with the sensors and controller from my MMU Electric Powered Rewinding project, enable automatic filament rewinding with various MMU and…
This is an auto rewind spool holder which relies on a friction/slip clutch for consistent tension, the spool is held tight on the hub. This is a low profile, easy to print, and hopefully improved version of the Auto-Rewind Spool Holders…
You need some extra (about 10cm) PTFE tube an a small screw to clamp the tube in the guide. I used 4mm outer diameter tube to add al litte braking, so that the printhead cannot push the filament backwards. This prevents the filament from…
List of norm parts, assemby model in readme file. To change stroke use suitable guiding element ("Krzywka").
