Liczymy pasujące modele…
Under body protection for the Omni Terminator from Rlaarlo. You can re-use the stock bolts. You have 2 options. The full ski protection or the just the sides plates (L and R). Recommended ABS/ASA, but works just fine in PLA. If you use…
I wanted to challenge myself with this CAD design and see if I could make a roll cage for my RC. The roll cage needs to be printed with some impact resistant material. I happily share this model for free, but it took me quite some time to…
Created this simple to print and use ESC Mount for the Rlaarlo Omni Terminator Mini 1/10 truck. Allows use of both double sided tape and zip ties - mounting to a rigid structure that uses stock screws.
I've had some trouble with the wheelie bar on the Omni Terminator. I've been bashing it pretty hard and it consistently results in the wheelie bar screws bending (the screws that hold the wheels onto the bar, M3X30). This design fits over…
Rlaarlo Omni Terminator Motor Gear Cover I designed this replacement gear cover for my Rlaarlo Omni Terminator because I kept getting small stones caught in the spur and pinion gears. The stock setup just leaves a bit too much exposed…
Center Brace Mounted Receiver Box for the Rlarrlo Omni Terminator. Made to work with stock receiver box lid and screw. Will require two M3 socket head cap screws and two square M3 Nuts. Glue a piece of neoprene or equivalent with a slit…
RLAARLO OMNI-TERMINATOR Roof protection
4/23/2026: UPDATED I made a new version that is much stronger and correctly lines as if it were in the original mount. This also works for the XTS-S10 Rally Car, and I assume the upcoming Short Course Truck. I wanted to get rid of the…
This is a simple battery extender and holder for the Rlaarlo Omni Terminator. It lets you run larger and longer LiPo batteries that do not fit the stock tray. The part moves the battery position slightly forward and gives a solid vertical…
Files include improvements to front splitter design, Fender vents (front), Flat floor, Rear diffuser, New rear wing design, wing mounting structure/servo mount, Server fan mount for motor cooling, working side duct to force cool air to…
10.05.23 Updated model made it more durable I crashed my RC car so heres how I solved it. Bores are meant to be re-drilled with 9mm and 2mm. Tab the thread M3 and you are ready to rumble again. Mirror model for left side. Printed in PETG…
When i saw Simon Vezina's awesome Omni Terminator rollcage, i decided to design and fit one to my 3d print test car, the MJX H16BM. It does not fit on the body but is just an open roll cage. You are able to attach the stock roof skids and…
Rlaarlo X12S Part(s)
Servo Mount for RLAARLO OMNI-TERMINATOR
Included are files for a front splitter, a rear wing that is 200mm wide and has a smoother airfoil shape than stock, and side body retainer. Consider the front splitter a work in progress, it's a bit thin in the mounting area but…
I found a few already online and I found that they sucked so I made one that works slick and is really stout. This adapter allows a full size steering servo to be used on the Rlaarlo Omni Terminator Truck and XTS S10 Rally Car.
My first attempt do make a dust cover for my new rally car. Should stop some debris getting inside (hopefully) still to try in harsh conditions. printed in PLA Depending on your machine settings could need some little sanding to perfectly…
The battery of my RC car dropped out 1 times too many and I came up with this solution. You will need some kind of foam rubber (see picture). The fit is pretty snug. Initially I wanted to print it in PLA as prototye and PETG when…
I was little disappointed when i discovered that case doesn't have room for car and controller at the same time if spoiler (wing) was mounted. And as other cars, Rlaarlo doesn't have spoiler that can be removed with clips. So i DESIGNED…
This is a collection of X12S Parts and FPV mounts I created. The skid plates and mud flaps attach using 3M industrial double sided tape and the FPV components mount using either screws into existing mounting points or zip ties/lacing…
Relocation for receiver box off of servo onto angled center brace rails
Rlaarlo Gladiator ROG1 Dumbo RC X10F(G) Receiver Tray Adapter. This is a reworked tray to house the X10F(G) receiver that allows the larger receiver to fin inside the stock chassis. I used PLA at 100% for the stiffness since this part…
This is an evolution of my first design. The mounting system using threaded inserts and using a tall block of plastic instead of individual standoffs is much improved and the splitter mounts rigidly to the car. I wanted to increase front…
2mm Shock spacers for the ak787. They snap onto the turning collar and add 2mm of preload. The shock slides into an outer ring to keep the spring centered on the shock like it should be. I print everything in Petg. This was with 3 walls.
Modified Wheelie bar wheels to replace stock ones. Print two modified wheels in PETG at 100% infill. Remove stock wheels from ends of wheelie bar and install new ones on the middle of the bar. The modified setup holds up much better for…
For those wanting to tame the RLAARLO 917 for on-road fun, these inserts provide much needed stability in cornering and acceleration for the rear of the car. They are a tight fit, and once pressed in place, use an 1/8 drill bit to size…
Rlaarlo JK07 shovel and jack mount, bolts on the tail gate carrier with 2mm bolt. Print 2 mounts, drill the carrier and screwed the mount on with 2x12mm bolt. The shovel and jack snap in place. The jack is printed at 130% to fit 1/7 scale…
here the clips I use to hold the dust cover. just glued to the frame. you can find the cover here: https://www.printables.com/model/1364607-rlaarlo-xts-p12-dust-cover
This is a replacement suspension arm for the Rlaarlo Rog1 RC car.
My wing kept breaking off every time my Stormbreaker would hit it when it flipped. I made this as a replacement since if you add rigid bushings it tears out the thread area of the wing mount. The center bushings are intended to be TPU for…
A printable replacement-style rear body guard for the Rlaarlo Omni Terminator , featuring a ribbed top, raised ends, and a rounded wraparound backside. I designed this to replace my missing rear guard using measurements from my truck and…
Here is a replacment swing arm insert for the Rlaarlo ak-917. The original kept on breaking so i designed this one and printed out of tpu and it hasnt broke once. Recommend printing in tpu with supports.
Just a quick scan of an Rlaarlo ROG1 front bumper. Figured it might be nice to model from and make getting a few dimensions easier. I haven't really figured out 3D scanning in general so bare with me for uploading so many versions of the…
Simple clip to secure the table top to the legs on a Rlaarlo JK07 camping table. Simply print and glue to the corners of you table top. I used 4, but you only need 2.
I designed and printed this battery riser so the AK-917 can fit taller batteries, my Ovonic 3s 5200 was a bit too big to fit. It works together with the original rear battery clamp arm and a redesigned front part. The riser just lifts the…
PLA worked fine on my car. I set my car's ride height to 24mm in the front and 26mm in the rear. With the kit perches you won't be able to get nearly that low without cutting springs, which changes the rate and is hard to do exactly the…
Rlaarlo Gladiator ROG1 Dumbo RC X10F(G) Receiver Tray Adapter. This is a reworked tray to house the X10F(G) receiver that allows the larger receiver to fin inside the stock chassis. I used PLA at 100% for the stiffness since this part…
4/23/2026: UPDATED I made a new version that is much stronger and correctly lines as if it were in the original mount. This also works for the XTS-S10 Rally Car, and I assume the upcoming Short Course Truck. I wanted to get rid of the…
Simple clip to secure the table top to the legs on a Rlaarlo JK07 camping table. Simply print and glue to the corners of you table top. I used 4, but you only need 2.
Rlaarlo JK07 shovel and jack mount, bolts on the tail gate carrier with 2mm bolt. Print 2 mounts, drill the carrier and screwed the mount on with 2x12mm bolt. The shovel and jack snap in place. The jack is printed at 130% to fit 1/7 scale…
Relocation for receiver box off of servo onto angled center brace rails
My wing kept breaking off every time my Stormbreaker would hit it when it flipped. I made this as a replacement since if you add rigid bushings it tears out the thread area of the wing mount. The center bushings are intended to be TPU for…
I found a few already online and I found that they sucked so I made one that works slick and is really stout. This adapter allows a full size steering servo to be used on the Rlaarlo Omni Terminator Truck and XTS S10 Rally Car.
This is an extended battery tray designed to fit my very large 3S CNHL batteries here and here . The maximum battery dimensions are now 178L x 69W x 40H
