Liczymy pasujące modele…
This is a remixed, further increased by 20mm to improve the air circulation. This is to improve air circulation under the printer to the motors. This fixes issue with unstable long prints which could overheat the motors and excessive…
J'ai réalisé une protection du ventilateur pour la Tina2, en m'inspirant de celui de la Tina2S. Print Settings Printer brand: Zortrax Printer: M300Plus Rafts: Yes Supports: No Resolution: 0.2 mm Infill: 100% Filament brand: Zortrax…
This Will Need Supports I needed to get my Tina2 off the table top to reduce the noise, but I wanted something a little more… “eccentric” than what I was able to find. I was originally going to just print a set of Rinoa's feet, but got…
Mit diesem Filamenthalter könnt ihr 1kg Filamentrollen an eurem Tina2s benuten. Einfach den originalen Filamenthalter abschrauben (2 M3 Schrauben) und diesen hier wieder anschrauben. Gedruckt mit dem Tina2s selbst. With this…
The same Model as the original, just separated and ready to print directly on the Tina2 itself
I'm using this shorty remix of Angryhulk's spool holder with 608 skateboard bearings on my Ender3 and wanted to fit it to my small army of Tina2's. For the record: Tina2's go by many different brands and names. Bresser Raptor, Monoprice…
Just a better arm for TINA2. No Glue needed I printed all these pieces without support.
I've Tested the profile to make sure that the Printer would not Crash into Itself while Covering as mutch Bed surface as i could The only drawback of this profile is that the Printer will stay idle until it reaches the Enstablished Bed…
This bracket holds full-size 1kg spools of filament far enough back such that they do not foul the extruder mechanism, and the filament unrolls smoothly. It is remixed from the excellent "hook" design from another bracket, so the weight…
Because my second little printer Bresser raptor 3D ( or TINA2 ) has only holder for 0.5 kg filament so I decided to make a better coil holder which is 1kg and of course bigger. I recommend printing from PETG material to a line thickness…
Dieses Teil verhindert, dass die Spindel der Z-Achse wobbelt
I found a model similar to this, but the fitment was poor, it could wiggle into direct contact with the heat-block because the clips were very misized for the geometry present.. So I remade my own from scratch, with as reasonably precise…
This filament spool holder is designed for easy removal of the lever/beam, such as for traveling. Simply slide it up to remove. Without the lever sticking out, it's easier to pack. The lever allows two bearings but I found it worked best…
This design is an upgrade for the spool holder in the TINA2. The holder will have some problems with the bigger spools since the height of the printer is small to start. Instead of giving it more height for clearance I chose to use the…
The included profile with the Entina 3D Tina2s works fine, for basic models. But it has some stringing and is made to conserve filament. which means it isn't really the best quality. I've gone through all the setting and changed most of…
Without a clip over time the bowden tube slipping in and out of the fitting coupler. It ruins 3D printing. In the worst case the tube pops out of the fitting and must be replaced. This applies to both the extruder and the hot end. The…
This Tina2 full size spool holder uses the original nut and bolt. works great with no interference with the extruder lever.
Tina2 Filament Guide If, like me, you have a Tina2, but you're using a 1kg filament spool, then you have an external spool holder, or an extension of the original one. In this situation I noticed that the extruder sometimes struggles to…
The Weedo Tina2 have a 100x105 bed and this remix of the original Mini Spool holder use the full volume to provide the maximum distance between the bearings (no change vs. original).
J'ai réalisé une protection du ventilateur pour la Tina2, en m'inspirant de celui de la Tina2S. Print Settings Printer brand: Zortrax Printer: M300Plus Rafts: Yes Supports: No Resolution: 0.2 mm Infill: 100% Filament brand: Zortrax…
Print Settings Printer brand: Zortrax Printer: M300Plus Rafts: Yes Supports: No Resolution: 0.2 mm Infill: 100% Filament brand: Zortrax Filament color: White Filament material: ABS-2
Remplacement des douilles à bille LM8UU du plateau par des douilles en pur plastique iglidur® RJ4JP-01-08, limitant les bruits de déplacement en Y. Utilisation de l'ASA comme type de filament.…
This Will Need Supports I needed to get my Tina2 off the table top to reduce the noise, but I wanted something a little more… “eccentric” than what I was able to find. I was originally going to just print a set of Rinoa's feet, but got…
I sliced it using the Tina2 version of Cura at the Normal profile. No Supports, no Adhesion. You can print all 4 at once. The Original works but is a bit unsteady. I added the Taller&Stable version to address this.
Enclosure for the Tina2(S)/ MP Cadet. The door with the window is designed for a 1mm glass/plexiglass. The print is made to be paused and the glass inserted. You can use the template as a guide to cut the glass/plexiglass. PLA doesn't…
Just enough space to hold a couple of things for the Tina2 / MP Cadet. The left side and the right side are different lengths from the slot on the top of the. SO unfortunately they are not interchangeable.
The "my kid doesn't know how not to touch the 3D printer button" cover
Start G-code lengthens the purge line to better remove any filament pieces that may be stuck to the nozzle and places it outside the print area (100x110x100). End G-code presents the completed print more forward at the end of the print to…
Drawer to go under the printer. The 80mm drawer is pictured. It turned out much bigger than I thought so I created the 50mm drawer as well. I also included a cover for the Y-axis belt. Although unlikely, I would hate for someone to put…
A little remix of the Anti-Z wobble mod for the Tina2 V3 by @Wingertsknorze. Update for the Tina2 V7 (and it's clones) that does not have a nub on the end of the Z-axis leadscrew, requiring a larger hole to insert the leadscrew. Added a…
