Liczymy pasujące modele…
Need to mount your shiny TS4 under your desk or monitor stand? This print will do the trick. Once the bracket is mounted, the TS4 can be easily slipped in and out via the integrated retention clips. Simply attach the cables to the back…
My goal was to design a CalDigit TS4/3 under desk mount that would fit my needs: Multiple mounting options, under desk, desk top, wall mount etc. Tabs that to retain the dock but allow for easy removal should you need to remove the dock…
I got a Park Tool TS4.2 wheel truing stand from a shop that was closing a while back. With it being used, it didn't include the caliper caps. For a while, that wasn't a big deal, because all of my wheels were aluminum. However, I've…
This box for TS457 Battery tester , have place for charger board, 18650 battery and connector.
I've been exploring solutions to mount my CalDigit TS4 under my desk. However, I had specific challenges with my desk having a false bottom. I had limited horizontal space and couldn't insert and remove the TS4 easily. Taking inspiration…
Under desk support for the (big) power supply of the CallDigit TS4 dock. You can detech the power supply without unscrewing the support.
I had been looking at @JasonLang_99641 TS4 Brackets , but they didn't have enough vertical space for a desk controller + dock (under the controller), so I decided to create a mount to include the controller and offset the TS4 dock to…
Matches taper on torch body to hold securely. Torch snaps into and out of holder. Mounts to wall or whatever you care to with three #8 screws (I used simple plastic wall anchors). The source ViaCad model is included, though I didn't…
I wanted to be able to mount my Caldigit TS4 under my desk, while maintaining as much airflow as possible. These brackets fit snuggly and allow for both wall and desk mounting. They are designed to fit both the fixed gray rubber foot, as…
About A personalized remix for easy component searching, extra ports for oversized batteries, and easier assembly. Components All the components I use for the products are purchased from the links below (or can be replaced with similar…
Parts for this specific RC car seem to be going NLA and incredibly hard to find for the right price This is still WIP and I would still have to add a battery holder to it but right now it fits and the servos fit Added fusion360 file so it…
Mounting brackets for the CalDigit TS4 docking station. Suitable for both horizontal and vertical mounting orientations.
This tool is for installing and disconnecting TS4 (Trina brand similar to MC4) connectors on solar panels and extension cables. You need 2 of these to install a TS4 but only 1 to disconnect them. Note: the prongs for disconnecting TS4s…
A solution for the lack of a fingertip spinner on the VFO knob on the Kenwood. Beveled hole for comfortable use. Simply glue onto the front of the knob. Category: Electronics
This is an Underware mount for the CalDigit TS4, generated using Andy Levesque's Underware generator. I don't really claim any ownership of this, since I just put the dimensions into Andy's code and this is the file it produced. I've…
Ultra-compact, ultra-budget internal resistance tester / milli-ohm meter based on the TS457 modules available on AliExpress. It's primarily intended for finding the internal resistance of batteries (up to 45V), but it works just as well…
Remixed version of Apocrathia's replacement tips for the Park Ts4.2 with more rounded contact patch
This is minimalistic Amazfit GTR3/GTS3/GTR4/GTS4/T-Rex2/Cheetah charging stand. Original model was created for round Mi Band charger. I recreated the similar model from scratch when I have switched to Amazfit GTR3. Requirements: M3x12mm…
The FNIRDSI DSO-TC4 is a multifunctional transistor oscilloscope, to protect its display I created a cover / sleeve. It is a snug fit, the lever of the transistor tester can be used to lock the cover. I printed the cover / sleeve with the…
NOTE: This part has not been printed/tested yet. It might tip… I needed a clean-looking stand for my laptop and a spot to put my Caldigit TS4, so I created this laptop stand. The stand sits at a 20 degree angle, and I can easily adjust it…
Cool off that way-too-warm CalDigit TS4! Fits 2 40x10 fans! Before - 1 hour of heavy use: 51c measured TS4 enclosure temp After - 1 hour of heavy use: 34c measured TS4 enclosure temp BOM: Branding doesn't matter - this isn't meant to be…
A perfect-fit under desk mount for the CalDigit TS4 Thunderbolt docking station! Features Front of the dock stays clean. Great for front facing mounts Dock stays locked-in due to two small buttons that lock in the ribbed surface of the…
Table Mount for CalDigit, Category: Office
This is a slide on cover to conceal (with a colour of your choice or paint) an ABUS Door Closer TS40 door closer. I wanted a door closer that I could disable with ease but I also wanted it to be easy on the eye. I have included an…
Scheppach Vacuum Connector (TS4000) Anschlussstück für eine Scheppach TS4000 Kreissäge an eine Absauganlage
Replacement Rack Rail Connectors for IBM TS4300. How to use: https://www.ibm.com/docs/en/ts4300-tape-library?topic=installing-modules-in-rack#tsk_3U_rackmounting__Mount_rail_to_block Printing only the part that you need (round or square,…
Scheppach Vacuum Connector (TS4000) Anschlussstück für eine Scheppach TS4000 Kreissäge an eine Absauganlage
Ultra-compact, ultra-budget internal resistance tester / milli-ohm meter (MOM) based on the TS457 modules available on AliExpress. It's primarily intended for finding the internal resistance of batteries (up to 45V), but it works just as…
Simple for printing enclosure wuth 18650 battery, charge controller and charge indication LED BOM: + LED 2x5 square lens (optional: use for replace SMD led from charger and place DIP into 3d printed box) + TS457 module + 18650 LiIon…
Housing for TS457, TS459. A device for measuring internal resistance to constant voltage. The device has a built-in 18650 power supply and a TP4056 USB-TYPE C charging board. The device also uses the GX12M-4B connector for compatible…
A long time ago the second gear of my RC car broke. I printed a replacement part waiting for the original components to show up. I hope this helps someone! 04/08/2023 Update: Due to popular demand I designed the 41 tooth gear. I hope it…
Thank you for viewing this model. If you download this or print it, you are required to send me a tip via Monero (any amount) and leave a nice comment. My open alias ID is: edison.me Or you can send to the address at…
Bracket for under-desk mounting of CalDigit TS4 power supply. Designed in Fusion 360.
![Mini Internal Resistance Tester [TS457]](https://media.printables.com/media/prints/1623939/images/12214072_5881d1c1-e25b-44dd-9039-d79ebbe03d05_47011d00-ea89-45a5-8b42-33dac92327d6/large_display_img20260302211117_1623939.jpg)
