48 modeli
If you have a velomobile with a 19 mm rear axle (like alpha 7 / 9, M9, DF, Milan, Bülk) you know how hard it can be to mount the rear axle because the spacer inside the hub gets misaligned. This tool helps guiding the rear axle through…
When mounting the rear wheel with a 19 mm rear axle, holding the axle–screw in place can be a real PITA in the limited space within the wheel well. This tool helps holding that screw, so it can not slip out of your fingers. Measurements…
Mounting the rear wheel in velomobiles (alpha 7 / 9, DF, Milan and such) can bee a PITA because the ratchets must be pushed into position… This little tool holds them in place instead. Attach a string (or a wire / spoke) to pull it out…
The idea is self explanatory, I guess. For those of you daring enough to make changes to the design: good luck! I did not make the FreeCAD project very user friendly to edit. With the sk_Master sketch, the basic shape of the velomobile…
I took the simplified design of my chain guard for velomobiles and tailored it to save some weight. The resulting design is not so “user friendly” like the original FreeCAD project anymore, so I decided to share print ready files only.…
Heat up the end of the chain tube with a heat gun. Then press the tube onto the tool to form the funnel like shape and wait until it cools down. The widened shape reduces chain friction and wear of the tube. Printed in PETG, 0.2 mm layer…
Print in (tough / ABS-like) resin or on FDM printers, as you like. Pre-supported model and also 3mf with suggested print settings included.
Handyhalter für ein Velomobil, passende Halterungen für einen Radlenker können verwendet werden, gedruckt in PetG in 2 Teilen um Stützen zu vermeiden, befestigt mit starkem 3M doppelseitigem Klebeband - Klebestelle gut vorbereiten/reinigen.
Jig to help you accurately set up the steering on your velomobile. This isn't something that should need doing very often, but accuracy matters - if the wheels don't run parallel to each other, you'll be wearing tyres out fairly quickly,…
To make my alpha 7 velomobile even more efficient I decided to remove the chain tube from the driving side. The chain is now covered with this tunnel to prevent small parts getting into the chain. You can easily adapt it to fit your…
A model specific for the Alpha 7 and Sigma Blaze rear light. Light is mounted up-side down to minimize the angle need to make it vertical. Print the two parts and glues some cutoff from an old tube on the back of the small spacer, use two…
Material: ABS Infill: 5% Infill Type: Adaptiv Kubisch
Hook for DF(XL) velomobile racing hood. The manhole edge of DF velomobile is quite sharp and hurts my shoulders in large bumps. I put rubber edge protection strip like this one…
In the W9 velomobile there is just enough space to keep the water bottle between tank steering and outer wall when the bottle is angled backwards. Therefore a ring shaped bottle holder should be the best. Take some double sided tape to…
I wanted some extra visibility on my velomobile - particularly when riding at sunrise / sunset, so I designed this to go on the top. With a pair of Exposure's Trace lights set to full brightness and strobing, it's pretty visible now! This…
This is a simple Lezyne Micro Floorn HPG mount for the velomobile. You only need a little Velcro tape to attach the mount to the wall of the velomobile.
Put load on the front suspension (sit in) and look how much space is between the elastomers and the white POM disc at the top. Then add washers in the right thickness to pre–load the front suspension and reduce shaking of the velomobile…
To cover the front axle / bearings and improve aerodynamics of the velomobile. Designed for 15 mm axles with 11 mm inner diameter. Printed in PETG, 0.3 mm, no support. Update: added tubes in two sizes (0.3 and 0.45 mm thick) you may glue…
I nearly lost my One X2 two times because of breaking mounts. First time a plastic frame broke, next time (see video) the DJI bayonet adapter. First step to the solution was to reduce weight by removing the battery from the camera, see:…
Requires 2 small wood screws to attach the flap to the body.
Handle to open / shut the velomobile race hood visor. Needs a 4 mm bolt for mounting. Mounting position may vary for individual needs. Printed in transparent PETG, 0.15 mm, no support.
now for SLA printing, manually supported model
console for the mount of a Sigma BC 14.0 speedometer you may change the angle within Sketch001
Alter count according to the number of elastomers you want to replace; you may also add some additional height. Print in PETG, see 3mf .
Another air outlet, that directs the airflow a bit more upwards, to where it matters. This was designed for my Tuna but probably fits a DF / DFXL with an aluminum mast too. I designed it with Autodesk Fusion .
Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset.…
in surface some deformity, but it goes always better good for play for child?
Protect your shoulders from the sharp edge of the manhole.
Permet de fixer un feu arrière de marque Catseye, sur un vélomobile Bulk.
are you velomobile fan? this is Light for my 2 ready model
Permet de fixer le feu Garmin (testé avec RTL515) sur un Katanga WAW en reprenant les trous existants (queue T3).
Permet de maintenir le levier de frein serré à l'arrêt
This is a support for Garmin Varia on back of a Velomobile.
Permet de cacher la roulette avant dans l'habitacle. Pour Katanga WAW. A fixer avec du velcro pour un démontage facile.
Original model by ChristianW: https://www.velomobilforum.de/forum/index.php?threads/der-vm-hupe-faden-hupen-horn.79369/#post-1872467
Druck Gehäuseteile aus hinreichend stabilem Material, LenkStockManschette und KnickSchutz aus Flex. Kein Support nötig. Details siehe .3mf Dateien. Zusätzliches Material Kippschalter mit Kappe ein/aus/ein, z. B.…
Designed for N45 magnets Ø 12 mm × 6 mm (rated 4.1 kg) and printing at 0.2 mm layer height. You can easily alter some dimensions in the VarSet. watchStrapOffset adds extra space between the holder's magnet pad and the part you wrap the…
Intended for the TPU camera holder (incl. bolt & nut), that comes witch the Thumb2. Use Ø 12 mm × 6 mm N45 magnets for the outer part (ActionCamMount) and Ø 12 mm × 8 mm for the counterpart. Print in TPU to protect the velomobile's paint,…
You may re-pack the battery pack that came with your velomobile, or use alikes (e. g. Ansmann 4S2P Akkupack 8x 18650 Kabel Li-Ion 14.4 V 5200 mAh) Additional parts 14 AWG wires, red and black 0,5 mm wires, red and black (display ->…
In the W9 velomobile there is just enough space to keep the water bottle between tank steering and outer wall when the bottle is angled backwards. Therefore a ring shaped bottle holder should be the best. Take some double sided tape to…
Permet de maintenir le levier de frein serré à l'arrêt
Permet de cacher la roulette avant dans l'habitacle. Pour Katanga WAW. A fixer avec du velcro pour un démontage facile.
This is a support for Garmin Varia on back of a Velomobile.
Original model by ChristianW: https://www.velomobilforum.de/forum/index.php?threads/der-vm-hupe-faden-hupen-horn.79369/#post-1872467
In the W9 velomobile there is just enough space to keep the water bottle between tank steering and outer wall when the bottle is angled backwards. Therefore a ring shaped bottle holder should be the best. Take some double sided tape to…
