Liczymy pasujące modele…
I wanted a simple hand tool to remove the oil filter in my car. Compatible with other brands and models of filters: WIX: WL7212 OE: 26300-35530 MANN: W8017 KNECHT/MAHLE: OC1255 FILTRON: OP617/1 Print with supports Category: Hand Tools
Looking for a better pedal placement for heel-toe action in your Veloster N? Well look no further because I have released my version of a pedal spacer bracket that doesn't just improve on the discontinued BRECKS spacer but I also added my…
Use at your own risk or print it out for decorations in the man cave! I was bored so I modeled my own turbo inlet. Printed it out using Siraya Tech PET-CF as it has the least moisture absorption out of all the other engineering filament…
FINAL UPDATE! I switched from FreeCAD to SolidWorks. What this allows me to do is redo the cone section like how OEM part looks like. Also made the cone section slightly smaller. Both these changes makes these pedal stops a little easier…
Made a phone holder to prevent the phone from sliding and the cable from flexing at the port. Fits a 2020 Veloster. Avoid PLA unless you want floppy plastic after a day in the sun. Print sideways on the wall. I used 0 top layers to expose…
This is a two part center cap to replace the stock center wheel caps on a Veloster Gen 2 Turbo style wheel. The main cap should be printed with PETg standing up so that the part will flex without breaking. The outer part can be glued and…
I had a broken hinge on my original cap and decided to try and print a new one rather than buy. I searched a few sites for an STL, and couldn't find one that would fit the Veloster. But, I came across Wischwasserbehälterspritzkappe Ford…
Tighten up your shifter even more than what you can get from just the shifter base bushings alone. Not many have dabbed into shifter cable bushings for this car. For other manual cars, many performance shops do this as soon as the new car…
I made this shroud to ensure that the reverse lockout spring can't slip over the flange nut on my shift knob extension. It requires a m10x1.25 flange nut that press fits into the bottom side of the cover. I've included the models so you…
I found a post on facebook where someone made custom printable adapters for the KICKER 48CWRT672 CompRT 6.75" Subwoofer, DVC, 2-ohm and a Dayton Audio Epique E150HE-PR 5-1/2" Carbon Fiber Cone Passive Radiator . The Metra 72-6514 wiring…
Tighten up your shifter even more than what you can get from just the shifter base bushings alone. Not many have dabbed into shifter cable bushings for this car. For other manual cars, many performance shops do this as soon as the new car…
Want to have a higher shift knob but don't want to increase the throw? Raise the whole base. Version 2 uploaded! All I did was make the center section thinner so it uses less filament. They are just there to make install easier.…
Make sure to print in ABS or ASA, as this goes in a car that may get very hot. Flip the print over or you will be using a lot of supports that are unnecessary. Print settings I used (Voron 0): Arachne, 0.2mm heights, 6 solid layers, 40%…
i couldnt find this online so i converted from a jpeg. archane may be needed for walls.
After blacking out the Hyundai logo in front the chrome strips on the front vents seemed a bit out of place. I'm not a fan of Plasti-Dip but I had little choice on my Veloster Turbo because of the forward collision warning system inside…
These two prints are the same as the two for the front mount Turbo Badge. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Infill: 20 Filament: Inland PETg Red Category: Automotive
This is a three part mount for the front of your Gen 1 or Gen 2 Veloster. Once you print the mount you will want heat the part up to mold it around the curve of the pumper. The picture came out orange due to my lighting but the turbo logo…
This is my remix of SummersideGuy's Veloster badge. This has been enlarged to match the diameter of the Hyundai logo for the Gen 2 (2019 - 2020) Veloster's rear badge. Two color printing can be done by swapping filament at 2mm. I'm doing…
Simple Silhouette of a Hyundai Veloster N. It is 2mm thick. I recommend sizing in only X & Y for your printer and double checking your slicer preview to make sure all lines will print. You may need to turn on “print thin walls” setting on…
Anything stored in the compartment slid around and made lots of noise. So I designed this which integrated my phone holder wedge into a divided tray with coin storage that attaches where the stock rubber liner would fit. Printed all in…
Rear seat pull tabs for the Hyundai Veloster should be suitable for every year (only tested on the 2016 model year). You probably want to print them with high temperatures in mind since they will be in a car, after all. I only have access…
