Wyniki wyszukiwania: vibrato

Vibrator holder

Pressure Point Massager using recycled toothbrush vibrator

If you've got an eye for quality, you've probably dropped some serious coin on the best toothbrushes money can buy - Oral-B's Pulsar toothbrushes. The bristles vibrate and scrub your teeth clean - but once the bristles begin to fray, it's…

Wand Vibrator Wall Mount

Thought I could make some slight improvements to dasNessie's mount for Hitachi wands, so I changed a few things: -Thinned the prongs for better compatibility with other brands of vibrating wands that don't tend to have such a large gap…

Tremolo / Vibrato / Whammy bar end cap

A cap for your Floyd Rose' stratocaster tremolo / vibrato / whammy bar. Snug fit for 5.2mm bar, scale differently for better fit. Use scarf Z-seam to eliminate inner hole bump.

Motor Gehäuse (Vibrator)

Fender Mustang Tremolo/Vibrato + Bridge "thimble" Routing Template

I couldn't find a good template for routing a mustang vibrato, so I whipped this up. Also has the locations for the bridge thimbles. (just a note about thimbles, these are based on stock thimbles, if installing a mastery they will need to…

Vibratory Tumbler

good tumbler 70mm fan with nut in one blade Print Settings Printer: FlyingBear Ghost 4S Supports: Doesn't Matter Resolution: 0.2 Infill: 25% Filament: none PLA RED Notes: I used red fillament because I don`t have black filament at this…

Paint Vibrator Stirrer Mixer Adaptor

This adaptor fits onto a pretty standard personal massage device that you just may have laying around. This particular adaptor is fit for an arboleaf massager but I've attached the fusion file so that you can edit the adaptor to fit any…

Stratocaster whammy/vibrato bar tip

Hello world! This is my first project. My whammy bar tip was hideous: it had no grip, really small and it was discolored due to use. I decided to try and print a new one that would suit my playstyle. PRINTING: You can print this with any…

PRS SE CE 24 electric guitar vibrato tremolo backplate

This is a replacement for the backplate for the PRS SE CE 24 electric guitar. You can customize it however you like

Moto Guzzi V7 V9 tank cap de vibrator

You think your engine is about to blow up but it's just the petrol cap going into harmonic chaos. This clips in and make the cap tighten snuggly. Good vibrations.

osVAC M32-Einhell-TC-OS-18-187 vibratory sander (osVAC Neo)

If required, the adapter can be fixed with an indicated screw hole. Thanks for Hobbyhimmel for inventing this system: https://www.ossso.de/osvac/

Hornady Vibratory Trickler Stand

I found that my Hornady vibratory trickler worked a lot better when tilted slightly and needed to be elevated to work with my scale and not get in the way. This stand tilts it 4deg and lifts it approximately 10mm on the left side. I added…

RCBS Vibratory Tumbler replacement feet

Replacement for the original rubber vibration isolation feet. This print makes use of the original hardware including the nut that is glued inside. Part dimensions should be close enough to allow replacing of only one foot as needed but…

Vibratoreinheit für Vibraphon / vibrator unit for vibraphone

This vibrator unit for vibraphone consists of flexible printed (TPC or TPU) valves for installation on a 6mm shaft and bearing housings and bearing support rings made of TPC. An M3 thread is drilled into each of the 4 shafts d=6 mm made…

Cement vibrator for Oscillating tool

quick tool to vibrate cement and get rid of trapped bubbles. It is 4mm tall, a bit less than 60mm long, print as sturdy as your cement mix requires (more perimeters/layers beat more infill). I printed mine 5 walls and 5 layers top/bottom,…

Vibratory base for 38x38 mould

NOTE print at 101% or higher if your printer cant print tight tollerances. For me its a super snug fit, if you have “perfect” non bulbous corners General purpose vibratory base for anything thats 38x38. I use it for moulds for high temp…

Vibratory isolator / decoupler for printers

this model uses two interlocking A brackets coupled with a string through a center hole to allow the printer to "jiggle" freely, the model includes brackets to affix to aluminum extrusion and additional brackets to tape to a table,…

Entlüftungsvibrator für Hydraulikleitungen

Wer in der Fahrradwerkstatt steht, kennt es: Die Hydraulikbremse bekommt einfach keinen guten Druckpunkt, weil irgendwo noch ein Luftbläschen ist, was einfach nicht raus will. Wir haben bei uns in der Werkstatt immer wieder gescherzt, man…

Fender Mustang Tremolo/Vibrato + Bridge "thimble" Routing Template

I couldn't find a good template for routing a mustang vibrato, so I whipped this up. Also has the locations for the bridge thimbles. (just a note about thimbles, these are based on stock thimbles, if installing a mastery they will need to…

Paint Vibrator Stirrer Mixer Adaptor

This adaptor fits onto a pretty standard personal massage device that you just may have laying around. This particular adaptor is fit for an arboleaf massager but I've attached the fusion file so that you can edit the adaptor to fit any…