Liczymy pasujące modele…
Note: The reservoir funnel is designed for one-directional use. The circular part goes into the water reservoir in the back of the WaterPik and the rectangle is supposed to fit onto the head of a sink. Although it is specially designed…
Wydruk około 0,50 €–0,61 € nettoWstępna wycena jednego wariantu
A holder for all the waterpiks that come with a waterpik flosser. Just printed it with PLA.
Brush and Waterpik holder. Printed in PLA. Easy to install. I use 3M Scotch Molding Tape (the gray tape with red liner) to mount it on the wall. Foam tape should do I as well. Print instructions Printed with 3 perimeters and 4 top and…
This is a simple Waterpik tip holder that holds 2 tips - leaving enough room below to allow for air circulation to aid in drying. The legs are 37mm tall (not including the top and bottom surfaces). The holes are 8mm in diameter. I…
This is a charging mount for a cordless, portable WaterPik Flosser. I mounted it on the inside of my bathroom cabinet door. I keep the flosser under my bathroom sink to keep the countertop clear. But the charger attaches magnetically to…
This is a lid for a travel model of Waterpik. Tinkercad: https://www.tinkercad.com/things/0iIiqmS6Ebo Print Settings Printer Brand: Creality Printer: CR-10S Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 15% Notes: Use food…
Designed in Onshape: https://cad.onshape.com/documents/7c0608bed246b091e5e6fe6d/w/5e95cee882fe90aa5edd86d0/e/2c381474cf9ae06fd74efe2c…
Simple cover to keep debris out of your reservoir. This cover fits snug, matches contours, and doesn't wiggle. Shouldn't matter what you print with, it's not supposed to get wet or hot. Printed here with Polyterra Army Blue Matte on a…
Simple wall mounted shelf for Waterpik WP-660 water flosser. Mounted on the wall using a single wood screw. I had good results printing with the back on the bed. Created a small cylinder volume of 100% infill behind the screw head.…
I made this to clear up some counter space on the bathroom counter. The original design intent was to just move the chargers for the 2 PhillipsSonicare toothbrushes to the side of the outlet cover. I kept revising it to accommodate more…
Last edited: 12 December 2023 Assemble your Oral-B Charger Cradle effortlessly by printing one case, two charger plates, and a bottom plate using silver Hatchbox PETG filament. For optimal results, set your 3D printer with a 0.4mm nozzle…
My family recently started to use the waterpik, and such we got new tips for everyone in the house. This holds an assortment of tips, with room to grow. 6 on top, 6 on the bottom, with a bit of a stagger I whipped this up with holes…
Simple holder for different Waterpik brushes and tips.
This is a custom-made Waterpik holder for the WP-660 model I made for my bathroom. It screws into the bottom of the Waterpik via 6-32, 1-¼ in machine screws. This model is imperfect, and I welcome anyone to come and make additions to this…
Holder for three Waterpik tips. Prints without supports. There is drainage through the bottom and a slot to prevent water from accumulating. Category: Bathroom
After buying my Waterpik WP-100 I thought about mounting it on the wall in my bathroom, I looked on the internet and only found a wall mount on Amazon UK but it was quite expensive, so that adding the cost of the wall bracket and delivery…
Holder/organizer for the Waterpik WP-500 Series water flosser. Specifically designed for the WP-560. Printed in PETG, .6 nozzle, .2 layer height on an MK4. The tolerances are tight - the flosser attachments fit perfectly in my setup.…
Gridfinity base for handheld Waterpik water flosser.
Wanted to get my daughter’s Quip brand water puck off the bathroom counter. Remixed from dmoto’s design that incorporates the original outlet cover. I printed in two pieces to both strengthen and to eliminate the need for printing with…
The Waterpik traverler was designed to use the reservoir inverted as a cover but it would be nice to have a set on cover once you are where you are going and set up. This is that cover. It sits inside and on top of the reservoir with two…
My Waterpik WP70 model didn’t have a wall mount so I printed one. A small screw needs to be put under the device, it has a small hole intended for this purpose. Print instructions Printed with 3-4 walls, infill 10-20% in PET.
Just slightly modified the model so the WaterPik can rest against the charger without the water tank. This allows you to dry the water tank separately.
I made it with PETG, but other materials can be used. It was printed on a Mini+ ( which it barely fit! ). Used 2 perimeters and 15% infill.
Remake of the Waterpik holder but with added drainholes to get rid of the water
After searching around in Thingiverse for a waterpik holder, I found that most of the design is meant to be wall mounted and not many were free standing. I ended up designing one for myself. I wanted something that can hold my waterpik…
Need a small wall mounted holder for the different tips that came w/ a WaterPik I got, so I threw this together real quick and mounted it to the wall with some double sides adhesive mounting pads. If you have more tips than this, you can…
Holds 5 waterpik tips and a tube of toothpaste. Gets attached to the wall with 1 inch 2-sided tape.
My Girlfriend got a Cordless Waterpik flosser for her Birthday. Strangely unlike my Waterpik that plugs into wall for power the carry case that came with hers had no way to secure them to the case so would make noise when ever you…
Replacing the batteries in WP560 Portable WaterPik requires a careful destructive removal of the battery (and motor) case bottom to get access to the batteries. This part is a battery door or bottom to use for re-assembly. Print Settings…
An organizer for the two of us for our waterpic heads, our toothbrush heads, all attached to the Philips Sonicare charger base to keep everything nice and organized. The holder.3mf file was created in PrusaSlicer. it includes a small…
Note : requires double-sided foam tape. The WaterPik cordless water flosser uses a magnetically attached charging cable which is convenient to attach, but which simply gets in the way when not in use. This simple holder holds the end of…
As the Waterpik set did not contained a stand for the toothbrush heads, I designed one. And as the coding color choice is very limited (and cannot be changed), I added a magnetic space beside every emplacement to individually mark every…
This was modeled precise to fit WP-660C. Other models of the same design may fit.
FYI: This is my first fully designed functional model. I learned a ton about iterative design and modeling things for printing. Someone I know had purchased several of these showerheads for their home from Costco, but was too short to be…
This allows replacing the smaller wand with a larger model version. The new holder press fits into the groove for the old one. I used this one: https://www.amazon.com/dp/B0BRSL99MW It's supposed to be for larger models but it works on the…
Updated to : ver. 2.2 . Some improvment. Added vent holes. Vertical tabs reinforced. After use and clean of our Waterpik water flosser, a stand is needed for driyng and placement on shelf. The openings at the bottom is for air circulation…
Bathroom Organizer for Sonicare Brushes and Waterpik picks.
This is a gridfinity compatible design print with no supports recommend slowing down first layer speed to help with better adhesion like all gridfinity prints. This design uses the gridfinity system designed by ZackFreedman
Es una base para poner los recambios de Waterpik, los cepillos de dientes.
I created this small rectangular piece to hold the extra tips that came with my waterpik flosser
Es una base para poner los recambios de Waterpik, los cepillos de dientes.
