P
PrintablesMarius M
CASE ESP32 2432S028 USB-C Module - Cheap Yellow Display (CYD) / CYD2USB
Basic case for USB-C version of the ESP32 2432S028 2.8" module, also known as Cheap Yellow Display (CYD) / CYD2USB.
- Pobrania
- 4804
- Polubienia
- 261
- Ocena
- 4,91
Wyniki wyszukiwania: yd2
Liczymy pasujące modele…
P
PrintablesRoadsideRC
RC Drift Magnetic Body Mount - for Yokomo YD2-Z RTR (Front and Rear)
Simple magnetic body mount for the Yokomo YD2 vehicles. I specifically made this for the YD2-Z RTR model. You will also need 12mmx3mm magnets, and some 1.5mmx15mm screws to attach it. It is designed for the screw to go through the factory…
- Pobrania
- 232
- Polubienia
- 29
- Ocena
- 0
P
PrintablesMrNeedlemouse
Yokomo YD2 Magnet Body Mount, perfect fitment!
Designed to be easily adjusted if needed for the perfect fitment, and works pretty well for walltaps due to the deep magnet cups! Additional hardware needed below, and pay attention to print orientations and mirroring the rear mounts. No…
- Pobrania
- 190
- Polubienia
- 19
- Ocena
- 0
P
PrintablesDerok123
Yokomo YD2 SXII Battery Holder (RC Drift)
Držák baterie na podvozek Yokomo YD2 SXII, jednoduchý a funkční koncept. I po instalaci je stále možné použít odklápěcí držák baterie.
- Pobrania
- 91
- Polubienia
- 12
- Ocena
- 0
P
Printablessp_cecadet
Battery tray holder for yokomo yd2z.
Securely cradle your Yokomo YD2Zs power source with our battery tray holder, optimal performance on every twist and turn! This is designed to be used with heat set thread inserts. these ones: https://amzn.to/3JR0gh6 Note these are not…
- Pobrania
- 65
- Polubienia
- 5
- Ocena
- 0
P
PrintablesdefMondo
Yokomo YD2SX3 esc wiring stealth mount
Mount plate to mount esc on rear difuser with wiring underneath right rear out drive. This mount allows you to run the power, motor, esc signal and sensor wiring underneath a place and underneath the right rear out drive on the YD2SX3…
- Pobrania
- 53
- Polubienia
- 8
- Ocena
- 0
P
PrintablesMartin Subie
Battery holder for short LIPO - YOKOMO YD2
Pad for a short battery to prevent movement. If you want a colored logo, it is necessary to change the color of the filament.
- Pobrania
- 53
- Polubienia
- 2
- Ocena
- 0
P
PrintablesVincent Mayer
Midnight Steering System for YD2
Ok, time to share the new Steering system files. I still haven’t been able to get a ton of track time with this, but it works well enough so far on 2 of my chassis. I tried to make this as simple as I could. If you have a stock yokomo…
- Pobrania
- 46
- Polubienia
- 5
- Ocena
- 5
P
Printablessp_cecadet
Rear ESC mount for yokomo yd2z
Two base holders. Both models use thread serts, these ones specifically, but any 3mm based one would work: https://amzn.to/3WvNU5w One holder is flat without nubs and sad. It is sad because it is designed to be used with VHB. Look how sad…
- Pobrania
- 42
- Polubienia
- 4
- Ocena
- 0
P
PrintablesElliot Birk
RC Drift YD2S DD Steering
A direct drive steering set with servo mount and steering arm made for Yokomo YD2S Printed on: Ender-3 pro No specific print settings needed My print settings: Layer height: 0.2 Infill: 100% !! NOTE !! U should print with something…
- Pobrania
- 26
- Polubienia
- 7
- Ocena
- 0
P
PrintablesMatthew Rockwell
Low Profile Pendant for CYD2USB (USB C Version)
A remix of the Low Profile Pendant design to accept the ESP32-2432S028 resistive version with a micro USB and USB C.
- Pobrania
- 24
- Polubienia
- 3
- Ocena
- 0
P
PrintablesDetson
DIY 100W USB-C Power Bank Case - 5x 18650 (5S1P), MYZL-YD24 board
I built my own 100 W power bank around the popular MYZL-YD24-V2.32 board ("100W 5S Flash Charge Mobile Power Circuit Board") and designed this case for it. The case is only 97 × 23 mm in footprint: five 18650 cells stand side by side in a…
- Pobrania
- 24
- Polubienia
- 6
- Ocena
- 0
P
PrintablesMarius M
Holder for ESP32 2432S028 USB-C Module - Cheap Yellow Display (CYD) / CYD2USB
A simple holder designed for the ESP32-2432S028 USB-C Module , also known as the Cheap Yellow Display (CYD2USB) . The holder can be mounted in either orientation. Additional hardware required: 2 × M3 × 6 mm screws 2 × M3 × 10 mm screws
- Pobrania
- 11
- Polubienia
- 1
- Ocena
- 0
P
Printables
Lower Profile Diffuser for YD2/RD1.0/SD1.0
This diffuser is about the same length as the stock diffuser, but it comes up from the chassis about 4mm less than stock. This means you don't have to cut your bumper quite as much to run a chassis mounted diffuser. Can be printed at…