1 / 6
SV08 Enclosure Doors, Hinges, and Magnetic Closures — image 1
1 / 6

SV08 Enclosure Doors, Hinges, and Magnetic Closures

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Minimalist hinges and closures for making your own enclosure doors using the stock mounting locations.

Rating
0 / 5
Likes
26
Downloads
230
Makes
0
Views
1,505
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial

Building your own enclosure from poly-carbonate sheet is a much cheaper alternative to buying the original. This design avoids external hinges that would require you to drill into your frame. These hinges use the original mounting locations, including those for the magnetic closures holding the door shut. Because of this, there is a bespoke door design to fit these components.

I prefer a clean minimalist look so the components are small and I skipped door handles since they're not strictly necessary.

If you're happy with my work, consider buying me a coffee for just $1. Small gestures give more motivation than you might think. https://www.buymeacoffee.com/FastLaneEngineer

BOM:

  1. 3 mm poly-carbonate sheet (PC allows you to drill without worry of cracking)
  2. Doors (x2) (they're symmetric)
  3. Hinge pieces (1 of each)
  4. Frame Magnet Holder (x2)
  5. Door Magnet Holder A (x2)
  6. Door Magnet Holder B (x2)
  7. M3x6 Screws (x28)
  8. M3 threaded inserts <6mm long (x8)
  9. 6x2 mm magnets (x8)

Fitment:

  1. Install the frame magnet holders on the machine.
  2. Install the threaded inserts into the door hinges.
  3. Install the upper hinges (both) on the machine. May need to tape them together.
  4. Insert the lower door hinges into the machine.
  5. Hold each door panel up in its place. Check for general fitment and clearance. Sand/cut as necessary.
  6. Mark the screw holes for the hinges on the door panel to later drill them out.
  7. Remove the doors and align the door magnet holders so that its edges align with the edges of the door. Door magnet holder A is for the lower left and upper right, B the opposite. Mark the screw holes on the door panel to later drill them out.
  8. Drill out the holes in the panel.

Installation:

  1. Glue the magnets into their holders, install the frame side holders on the machine.
  2. Install the upper frame hinges on the machine.
  3. Loosely screw the upper door hinges to the doors.
  4. Loosely screw the door magnet holders onto the doors (the threads on the screws will bite into the plastic, but do not over torque).
  5. Insert the lower door hinges into the machine.
  6. Mount the doors onto the machine by sliding the top hinge together, and loosely screwing the door to its bottom hinge.
  7. Adjust the panel to fit as well as possible, checking against the other door. With one door open, tighten the screws on the adjusted door. The bottom hinge should bear the weight of the door.
  8. Repeat for the other door.
  9. Done!

Some things to think about:

  1. Print in PETG or better for heat resistance.
  2. Use 4mm drill bit to allow for some adjustment.
  3. I cut the doors out by hand with a vibratory saw and therefore expected some tweaking. If you have these laser or water jet cut, I don't guarantee they will fit without any finishing work. However, I did design a 1 mm gap to the frame and a 0.5 mm gap between the doors.
  4. This design is intended for 3 mm sheet. If you go thicker the frame magnet holders will need to be thickened/spaced out to match. The hinge edge will likely need to be beveled to clear the frame. I don't recommend thinner sheet as 3 isn't exactly stiff, but acceptable.
  5. At 3 mm thick, the door can't just be thrown open since it will wobble and can bind against the frame and snap the plastic hinge pins. If you are aware of this it'll be fine. Worst case you print another hinge.

If you're happy with my work, consider buying me a coffee for just $1. Small gestures give more motivation than you might think. https://www.buymeacoffee.com/FastLaneEngineer

Tags