TPU feet for Creality Ender3 S1 Pro and alike (S1/S1 Plus and probably V3 SE/KE)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
2 versions of damping TPU feet with an effective height of whether 30 or 35mm for Ender3 S1 Pro and comparable printers.
- Rating
- 5 / 5
- Likes
- 7
- Downloads
- 54
- Makes
- 2
- Views
- 391
- Reviews
- 2
Updated at source:
Model information
- Source
- Printables
- Category
- Creality Parts & Upgrades
- License
- Creative Commons — Attribution — Noncommercial — NoDerivatives
Besides of noise and vibration damping, which works pretty well in my personal opinion, the primary goal was to lift the Ender3S1Pro print bed to the same height as the window of the enclosure tent at about 12.7cm/5in* for a good first layer observation as it is being printed.
After installation i came to the conclusion, that slightly higher feet could make print observation more comfortable. Therefore i have made a higher version for those, who own a comparable 3D printer enclosure and want to play it safe, so you can choose between the both:
The first published version of the feet (which i'm actually using myself) has an effective height of 30mm and a total height of 35mm. It should raise the S1PRO print bed to approximately 12.5cm height above the base level - which is in my view already sufficient for this type of an enclosure tent.
The second version of the feet is 5mm higher with an effective height of 35mm and a total height of 40mm to raise the S1PRO print bed to approximately 13cm height above the base level.
Slot dimensions: The slot on top of the feet is 21mm wide, 41mm long and 5mm deep. These damper feet should not touch the bottom plate.
* The mentioned enclosure tent is branded as “comgrow”, but i have seen similar looking tents with alternative brand names on it available.
3D-Printing a set of the feet
The model should be turned in the XY plane by 90 degree and put on a side (as to be seen at the CURA-Screenshot). The following settings are just an example of what i have used and currently consider as “working” for 3D printing using TPU95A with a 0.4mm sized nozzle (listing the most important things first):
I strongly recommend to use a “raft” to avoid warping issues (at least on a PEI-Sheet. I guess that more than 100 gram of TPU and several hours printing time should be a good argument for such a “little” safety measure.
I've used 35% of polydirectional infill, i guess smth. like Gyroid would be an optimal choice.*(see note)
Supports are needed at one of the sides only, while at the opposite side with small overhangs a support-blocker can be applied (as shown at my Cura screenshot) .
…than
I have used 3 Walls (with 1.2mm total width),
plus an “Alternate extra wall” option for a higher strength,
and also "Connect infill lines" (or “…polygons”).
To speed up the printing process a bit i've also used:
0.28mm layer height setting
"Adaptive layer height" option in CURA (in "experimental" settings section)
*(an additional note on infill): Choosing the pattern and the strength/density for the infill is probably one of the most crucial steps - not only because an insufficient infill could result in an uneven feet compression, but in general its density and shape plays a central role for its damping properties, as the structure is in charge of dissipating the vibrations and sound waves .
Have a nice print!
gexo (-graphix), 2024-2025
Made with FreeCAD on GNU/Linux.
Thanks a lot to all FOSS developer community volunteers who made it all possible.
All mentioned trademarks, brand or product names are property of their respective owners.
The license of the models has been changed on 18.06.2025 to CC BY-NC-ND