Counting matching models…
Reinforcement/Antivibration bracket for Tenere 700 with TFT dashboard. Designed for www.dr2.cz phone/navigation holders installed with use of mounting kit for World Raid/Rally version (link below).…
Print with the softest TPU you have and reduce the perimeters and bottom/top walls to as low as possible without ruining the print. There also is a washer included for the screws. Print it four times too.
I've been using this filter for ages now, and completely forgot to upload the remix I realy like The Filter, but not the lid, as it's a PITA to keep in place as is. So I added locations for 2 threaded inserts and corresponding holes in…
This is a simple multi-material, low-profile vibration dampener that utilizes thermoplastic polyurethane (TPU). The dampener itself is crafted from TPU for its excellent shock-absorbing properties, while the base is made from PETG,…
This part aims explicitly at vibration noise damping of the printers bottom plate in a very primitive fashion - by pressing the plate upwards from the outside. In my case a damper between 24mm (minimal) and 25mm (best) does the job. A…
This is a flexible TPU spacer designed to bridge the gap between thin motorcycle mirror stems (or windshield bars) and standard phone holder clamps. Most phone holders are designed for handlebars with larger diameters. These adapters…
I have remixed the Bambulab model for the Prusa XL. You can simply put the shoes under the original ones. The assembly is very easy. You only need to lift the Prusa XL carefully. A nice side effect is that the PrusaXL stands a little…
Standard 370 motor has a length of 30.5mm a diameter of 24mm. Printed in PLA with whatever default settings. The motor is held with zip ties to the mount. That ensures that there is no play. The mount is attached to the pedal with 2 M3…
A set of vibration dampener feet for the Centauri Carbon. I adjusted the feet to fit the CC. The original model had a curved bottom which resulted in slipping across the desk. I flattened the bottom and added screw holes to allow non-slip…
My Hamilton Beach Coffee grinder is either worn out or has issues as it vibrates annoyingly on the counter each time I use it- it's annoying but not as annoying as buying ground coffee so I needed to fix it. I designed this TPU base where…
I recently purchased a spool of TPU and thought of what should I test it with and as it goes with 3d printing, almost everything around the house can be improved with a quick print, and what better way to test my machines capabilities to…
Vibration Isolation Model: https://www.thingiverse.com/thing:3794194 (45x45mm version) Additional Hardware: - M3 Heat Set Insert The top plate has two versions. One for a 4mm heat set insert and another for a 6mm heat set insert. Each to…
I'd noticed that the XY100 (Also known as an iMakr STARTT ) printer we had was sometimes resting on the bottoms of the Z axis motors which isn't ideal. I designed this foot / base so that the acrylic main panels would be supported without…
Mounting bracket for simracing to isolate vibrations. Print inside from TPU. M8 screw hole in the middle.
When mounting PTZ cameras of a well-known brand on a thin wall mount, I noticed a visible wobble/micro-shake in the video image whenever the camera moves (zooming, reframing, calling presets, etc.). These adapter plates are meant to…
These legs come in two length and bolt into the two existing 3mm threaded holes on the bottom of the corners of a Core One. There are two versions: short (adds about 26mm of height) and very short (add about 16mm). Replaces or supplants…
Needed case for bigger DC motor. I used it with 6V and 12V double sided motors with 8500 RPM, dimensions are in image. 1/ Print case 2/ Place some gel double sided tape inside, or other insulation material inside. Layer it if needed. 3/…
TPU Anti-Vibration Feet for NAS Systems A small but highly effective solution for those who use their NAS on a shelf or rack. These TPU feet help isolate vibrations generated during operation, significantly reducing both noise and…
Extra Materials : 4x M3x6 Heat Set Inserts. 4x M3x6 Socket Head Screws
My Elegoo Centauri Carbon printer use to bounce around. I used the original model successfully. When my new Carbon 2 arrived, the feet no longer fit. I adjusted the rigid part of the model and kept the TPU model the same. I printed the…
The new CORE ONE L printer uses anti-vibration mounts on the Z-axis trapezoidal screws. I modified the model to fit on the CORE ONE / + printer. My Core One + after phase stepping calibration, reduced the vibration of the "Y" motor by 93%…
The trash bin was adjusted to be compatible with these feet: https://www.printables.com/model/1727-anti-vibration-feet-for-prusa-mk3ss-mk4-and-prusa . In order to do this I combined the trash bin with the holder tabs from the sidebox…
MK4 "Naked" Gyroid Dampers (TPU) - Anti-Vibration Feet Summary Sponge-like vibration dampers for the Prusa MK4 printed in TPU. Uses exposed Gyroid infill. Requires specific slicer settings (Vertical Shell Thickness OFF)! Description These…
80mm Acoustic TPU Fan Spacer (12mm Depth) – Integrated M3 Threads Eliminate fan whine and structural vibration with our premium 12mm TPU spacer . Specifically engineered for 80x80mm fans , this spacer acts as both an acoustic buffer and a…
MechSmith's Foot Mount works great to lock the feet into place. I however experimented with it a little bit and used Autodesk Fusion to turn it into a damper / absorber. This was originally meant for the FlashForge AD5X but it should work…
This is my idea of Anti Vibration Platform - Base for 3D printer. THIS IS DEMO IDEA, ONLY IN THE PAPER. I not printed jet, but here is STEP file to improve it. need : 45x15 cylinder bearings x 8 springs or can print some TPU to replace x8…
I use a vibration motor inside a remote control to alert of dangerous situations of the robot. The vibration motor I have, it is an open model so it can get tangled with wires inside the remote. Therefore I designed this small case.
NEW! Now with EVEN LOWER PROFILE! This version reduces increase to height of the printer. My prusa bear lives in a shelving unit now and I needed to reduce printer height as much as possible, but still wanted the noise dampening effects…
The original version was great when I had the stock hotend, but now I have a different one that needed more depth for the fan to be blowing in the correct spot for filament cooling. And, because I changed my entire hotend setup, save for…
This 3D model does not include supports; however, they can be added in Bambu Studio. It was printed using PLA filament on a Bambu Lab P1S. The design was created in Tinkercad. I hope you find it useful.
These are anti-vibration feet for the Quamar M80E. I have my grinder on quite a hollow table and it was making quite a lot of noise, this is why I designed these feet to make it more quiet! I have had these in use for about 2.5 years and…
universal anti-vibration feet TPU Flex recommended use double-sided adhesive tape to mount (optional)
AstroFlex is a set of vibration damping feet designed specifically for reflector telescope tripods. The internal suspension lattice allows controlled elastic compression under load, reducing micro-vibrations caused by focusing…
it uses a compliant mechanism to muffle almost all vibration note: it must be put under a pre existing foot as this one can not be attached
Wanted a larger footprint for my CC. Printed in flexible PLA. TPU could be used as well. Hope you enjoy.
TPU Printable Shock Absorbers for Padel Rackets Upgrade your comfort and performance on the court with these custom TPU shock absorbers designed for padel rackets. Engineered to minimize the transfer of vibrations from the racket to your…
Rubber feet diameter 8mm, no supports, tpu. Simple assembly into a hole with diameter 4mm. Lyer: 0,2mm Nozzle: 0,4mm Material: TPU Used for example here:
Marre des meubles qui rayent le parquet ou qui vibrent ? Ce modèle est la solution idéale pour imprimer des pieds de meuble durables et discrets. Conçu à l'origine pour un bureau en bois, ce kit de 12 pièces s'adapte à de nombreux types…
Material: TPU/TPE. Number of perimeters: 1-3 (for TPU A95) or 2-4 (for softer filaments). For optimal performance, for the "Side feet" model, use 1-2 perimeters up to 18 mm height and 3-6 perimeters above 18 mm. Top layers: at least 5 (1…
Support Internal Hexagonal/ Soporte Interno Hexagonal If you need other dimension increase the design for new model.
Vibration dampener for the IKEA MITTBACK Trestle. I have 2 3d printers in a wooden cabinet on a pair of the mittback trestles on the upper floor of the house. I noticed recently that the vibrations from the printers were being transferred…
Tired of that annoying buzz from your aquarium pump? The problem isn't the pump — it's the rigid mount transmitting motor vibration straight to the glass, which amplifies it. This is a drop-in TPU replacement for the stock rigid mount on…
YAAF – Yet Another Antivibration Feet This is a functional remix of the original anti-vibration feet for the Adventurer 5 series printers. The design fixes several practical issues from the original model and improves vibration damping…
Ender 3 V3 SE/KE Dampening Noise Reduction Anti-Vibration Feet - Remixed to fill in the gap on the bottom of the feet. May reduce Dampness but no supports needed.
Would recommend your own print settings. I printed these in tpu and they are made on and for my prusa mini+ howver im sure they could be useful with other printers i would recommend adjusting the infill to have 4 parts with the same…
📝 Description These feet are based on the original Voron 0.2 design, but are slightly extended in height to improve stability and reduce vibrations. The increased height provides better ground clearance and a larger contact area, making…
📝 Description These TPU foot extenders are designed as a clip-on upgrade for the original Voron 0.2 feet . They attach directly to the stock feet, increasing the contact area and significantly improving vibration damping and grip. Printed…
Printed in PETG, with 4 wall loops, 5 bottom layers, 50% Gyroid infill, 0.2mm layer height. Ignore the texture difference in the bottom foot in the picture - it was printed with 2 types of PETG as I ran out mid-print Parts list: M6 T-nut…
The simplest model for efficient work. It also prevents the machine from sliding on the table. (For this model to fit, the hole in the machine for mounting it to the table must be 10 mm and fit tightly.) I also recommend using this:…
This housing holds the Tuya ZG-103Z vibration sensor in place. It snaps into place, and also keeps it in a specific angle using the coin-open hole at the back of it. This way you can replace the battery without worrying about the sticker.
This is a vibration-damping wall anchor for tables or storage racks. Printers like having a stable platform, and these anchors are a cheap way to add some rigid support. Print with tpu, with the side opening down, without supports. 4…
Anti-vibration feet for Elegoo Neptune 3 Pro. I used them to isolate the printer from the enclosure I built to reduce noise, they are quite effective. They fit onto the existing rubber feet of the printer. Printed with Devil Design Black…
After implementing the vibration reducer feet on my 3D printer, I have noticed a substancial reduction in the amount of vibrations that the printer generates. In fact, my tests have shown that the feet are able to reduce vibrations from…
Vibration-dampening feet for the MK3/MK4 . Uses 4x double yellow dot squash balls. I wanted to make a version that does not add height to the printer to make it easier to fit into various enclosures. The design is inspired by several…
Introducing specially designed Anti-Vibration Feet for washing and dryer machines. Engineered to effectively absorb and minimize vibrations, these feet ensure a quieter and more stable operation of your appliances. Print setting…
These TPU feet are designed to decouple the BedSlinger from other 3D printers on the same surface by absorbing vibrational energy, helping to minimize machine wear caused by vibrations. Benefits When you place a single printer on the…
This is my design to reducer the vibration and noise transmission over the table.
The SP Connect Anti Vibration Module comes with a gear-style connector at the back because it is primarily meant to be mounted on motorcycles. The square stem mount found on bicycles featuring a built-in SP Connect mount is not compatible…
(IMPORTANT) Please download the User Guide for HULA v1.0. I do my best to double-check and test the print profile I created. They are up to date with the latest changes made to the designs. If you wish to purchase ready-to-use HULA feet…
Remix of the anti-vibration feet bushings by SomeDude with the holes for the screw head widened a bit to use M4x25 button head screws.
SV08 Antivibration Feet "Bambu Style" Hardware: Reuse original bolts to fasten feet. Printing instructions: Print Antivibration Feet in TPU. No Supports Needed. 10 to 15% infill. 3 walls for vertical and horizontal top and bottom. The…
Quick and easy HULA Anti Vibration Feet Adapter for Elegoo Neptune 4/4Pro. Simply remove the original foot of the Elegoo Neptune 4/4Pro and mount the adapter foot. Afterwards, the modified center core can be connected to the rest of the…
Reinforcement/Antivibration bracket for Tenere 700 with TFT dashboard. Designed for www.dr2.cz phone/navigation holders installed with use of mounting kit for World Raid/Rally version (link below).…
This is an alternative case for Creality's g-sensor for Ender 3v3 KE (and some other Creality printers), photo of the sensor in original case attached for reference. Original case opens easily, it's just press fit. Uses eight ⌀6×3mm…
There are two versions of Anti-Vibration Foot Covers for the Prusa XL here. One will keep the printer stationary while the other (with the purchase of 80 pound casters from Amazon) allow the printer to be moved for maintenance. The weight…
Reduce the vibration transmitted to your countertop and cabinet. These foot covers are intended to be printed in TPU Filament: TPU Layer Height: 020 3-4 walls 3-4 upper and lower layers 15% infill
Cost efficient Bambu Lab P1S and P1P feet are intended to minimize vibrations of chasis to improve printing experience and reduce noise. Please pay attention to printer settings: Only flexible filaments. I used TPU A90 Perimeters…
Schale: https://www.conrad.de/de/arbeitsschale-rot-inhalt-1-st-530263.html Category: Other
This design is made to fit MK2/S corner pieces with Anti vibration feet designed by Kilian Waltl . I liked the design of the anti vibration feet because they made the printer much more silent but I was worried about the feet moving over…
Ender 3 V3 KE Vibration Sensor withour extra screwes
Inspired by: https://www.printables.com/model/969418-synology-ds-1522-anti-vibration-stand
ASUSTOR AS5304T Vibration Dampening Feet These are vibration dampening feet for the ASUSTOR AS5304T NAS, that are printed in two parts using flexible filament. While the AS5304T NAS from ASUSTOR is a relatively quiet NAS when it comes to…
IF YOU KNOW THAT THESE WORK WITH OTHER PRINTERS, PLEASE COMMENT AND I WILL UPDATE THE DESCRIPTION! Noise and vibration damper feet for your Prusa that install just like those silly little rubber ones in the kits! These bad-boys will…
This design is specifically aimed at reducing vibrations on the Y-axis, particularly the bed, which carries the most inertia and tends to resonate at higher harmonic frequencies. In my tests using Klipper and an ADXL345 sensor, I've been…
Print with the softest TPU you have and reduce the perimeters and bottom/top walls to as low as possible without ruining the print. There also is a washer included for the screws. Print it four times too.
I've been using this filter for ages now, and completely forgot to upload the remix I realy like The Filter, but not the lid, as it's a PITA to keep in place as is. So I added locations for 2 threaded inserts and corresponding holes in…
paint-on support recommended as pictured Please refer to the original remix page for installation instructions: https://www.printables.com/model/621679-low-profile-squash-ball-feet-for-prusa-mk4-mk39-mk
I needed some vibration damping for speakers, but wanted them to me mounted in an fixed position and not chaotic. Thus I designed this part to have the anti-vibration pads under the box in a fixed position. Print the parts twice, they fit…
Antivibration feet that fits in the PSU side of the printer.
Download TPU printed parts and PETG printed parts from here https://makerworld.com/en/models/417509#profileId-319901 Use the center core for K1 or Voron
Improved Anti-Vibration TPU feet for Neptune 3 Pro/Plus/Max remixed from @Fe_ix design, with extra walls and reinforcements, also fixed the model so that the top left feet can fit the Anti-Vibration feet. Print Settings for Neptune 3 Pro:…
Made this design to use as feet for my Felixprinter Tec 4 . It also quiets vibrations from the printer somewhat. Printed it in black Flex can be printed also in TPU. I printed 8 of these to my printer. Probably can also be used on any…
Reduce vibrations and noise with these easy-to-install TPU feet. Designed to fit inside your original Bambu Lab feet. Easy Installation. Recommended print setting for TPU-95A hardness: Wall loops: 2 Top shell layers: 3 Bottom shell…
UK: Google Translate Feet Vibration dampers for Prusa 3D Printer I have made a "sandwich" construction with the rubber material "Spectrum 90A S-Flex" and the plastic material "PETG Prusament" to improve vibration damping. I think it has…
Vibration absorbing feet for the Voron 2.4. Those that came with my kit were already flattened. So I printed my own using TPU90 from Polymaker. They work like a charm. I used PIF settings for the print.
This is a simple multi-material, low-profile vibration dampener that utilizes thermoplastic polyurethane (TPU). The dampener itself is crafted from TPU for its excellent shock-absorbing properties, while the base is made from PETG,…
Greatly reduces the amount of vibration transmitted to the table (and therefore the floor) without decreasing print quality. Printer will shake violently at high accelerations but it will not impact its stability or whatever it is…
Antivibrationsfüße für 25x25 Tischbeine Gedruckt in TPU. Schichthöhe 0,2mm / Infill 25% / keine Supports
Unscrew the rubber feet underneath the qidi plus 4 and replace them with the fitted core. I also included the step file for you to customize and adjust. Follow instructions on the Hula pdf found here:…
After I noticed that the original G sensor mount was slamming into the camera mount that I created, I tried to find something that could solve my problem, but nothing. I created this starting from the model from Jose NR (chek it out; the…
Add on for “Anti Vibration Feet by Datafreak” (https://www.prusaprinters.org/prints/66846-prusa-i3-mk3s-anti-vibration-feet) Simple feets, fitting into the OEHLBACH Shock Absorber Adapter for MK3S+. Hole on the bottom if you don't have…
models are printed from TPE, but TPU can be used too. For this to work u print 2x antivibrationsupport and 4x antivibrationsupport 2. The first ones are on the frame behind motors and antivibrationsupport 2 are used always pair. One pair…
This is designed to use silicone hose to damp vibrations. It works well with 21mm OD - 12mm ID silicone hose. Both f3d files are parametric. You can easily change them to your needs. → in fusion360 → design → solid → "modify" dropdown…
Just squeeze a double-yellow dot squash ball into the mount. Use double sided tape or screw on flat portion of the pad to mount onto your speaker or equipment.
![silicone hose universal vibration damper [parametric]](https://media.printables.com/media/prints/108116/images/1073110_cc4e0a4c-3c1a-4684-a25d-92bb3ee5a9c9/unknown.png)
