1 / 9
LW-PLA Dual Egg Capsule for Model Rocketry NRC Competition — image 1
1 / 9

LW-PLA Dual Egg Capsule for Model Rocketry NRC Competition

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Estimated printing price per file

€0.11 – €0.14 net (excluding VAT)

For file: Dual_Egg_Throat_24mm_ver4_0.3mm_PLA_MK4_9m.bgcode

This is an estimate for one file. You’ll confirm the exact price before ordering.

File and estimate settings

File used for this estimate

Average indicative estimate: €0.12 excluding VAT (range midpoint).

Weight reported by the author
1 g
Print time reported by the author
9 min
Source material
PLA
Estimate material
PLA
Estimate printer
Bambu Lab P1S - 0.4 nozzle
Estimate process
0.20mm Standard

Indicative estimate for the selected file only, based on the author’s weight and print time. File variants are not added together. The final price is calculated after file analysis.

Saved on this device.

Dual Egg Capsule printed with LW-PLA which is lighter than a Vacu-formed capsule. Specifically designed for NAR NRC use.

Rating
0 / 5
Likes
1
Downloads
18
Makes
0
Views
118
Reviews
0

Updated at source:

Model information

Category
Other Ideas
License
Creative Commons — Attribution

A Dual Egg Capsule (2 eggs) for Egg Loft Altitude events, specifically designed to be printed with LW-PLA. Modeled and created to fill a need for rocketry hobbyists as no commercial Dual Egg capsule kits are available. Foaming LW-PLA can actually produce egg capsules that are lighter and just as strong as vacu-formed styrene capsules.

Base Elements:

  • The top cone is elliptical in shape and holds one egg. 
  • The bottom cone is basically the same shape but has an altimeter shoulder section built in to accept a variety of NAR or FAI approved altimeters supplied by the contestant. The second egg is placed in the bottom cone. The shoulder altimeter bay is designed for 24 mm airframes
  • 2 couplers are printed and then glued together with CA glue to form a “double bulkhead”. This joins the two major pieces of the capsule together. Tape is used to seal the two halves together
  • A coupler extension insert or plug for the altimeter shoulder bay. This adds strength and seals off the altimeter from ejection gases. 

Contestant provides:

  • Sandwich bag or plastic wrap for each egg. Highly recommended
  • Must punch altimeter air sensing holes in the bottom cone shoulder for proper operation of altimeter. See Altimeter vendor for sizing and further info.
  • Kevlar Cord and punch two holes in bottom coupler extension. Attach to extension then glue with CA into Altimeter shoulder extension.  Be careful to avoid the altimeter holes.
  • 24 mm sized booster rocket not included.

Settings for LW-PLA

I used these Prusa Slicer Settings for eSUN LW-PLA on my PRUSA MARK 4 for all the files with the exception of the coupler extension which I treated closer to regular PLA for added strength.

Extrusion Multiplier0.35
Nozzle first Layer230 C
Nozzle Other layers240 C
Perimeters2

Tips for Printing - PRUSA

Foaming Factor

The foaming that causes the filament to expand is activated by heat. The amount of heat is defined by nozzle temperature and print speed. Faster printing will need a higher printing temperature to achieve the same expansion. The maximum expansion of three times the original size is achieved around 240 - 250 C. 

Extrusion Multiplier

The extrusion multiplier depends on the foaming facto, so the range 1-0.35 can be used. The lower the extrusion multiplier, the lighter the model will be.

Oozing and Stringing

Due to the material expansions, retractions are ineffective. This causes prints to have a high amount of oozing and stringing. LW PLA is, therefore, more suitable for printing in a single pass, such as the vase mode when available.

Assembly 

A #100 lb Kevlar stranded cord or string is recommended for the coupler plug insert. A length of elastic in between the Kevlar cord and parachute is highly recommended to absorb the opening shock from the parachute.

The parachute should be strong enough to take the stress from the 110+ gram payload. See the NAR.org site for specifications in the US Sporing code for this event related to contest eggs and approved altimeters. Enjoy

Altimeter Hole Location

I found out the hard way that the altimeter air holes should be drilled almost midpoint in the shoulder extension. Glue the coupler plug insert with a medium CA gel and let it set up. Then using the 24mm Altimeter Hole jig drill the air holes almost at the midpoint right into the two layers of LW-PLA. Download the hole jig file and print in regular filament. This will help in centering and drilling the altimeter air holes. Note I do not recommend using a hobby knife to punch the holes as this often results in a tear or stress fracture across the holes, especially in warm air or sunlight.

OPTIONAL: Throat Shoulder

ADDED a small throat shoulder or extension to ADD extra support at the cone base connection for the altimeter extension. This can be inserted and either glued with CA or left as is.

Range of Eggs:

This capsule is a recreation of previous Out Of Production OOP Dual Egg Capsules. It will fit EGGS as defined by the NAR Sporting Code. 

 

 

Tags