Counting matching models…
Does NOT work with the Scimitar RGB as it has different layout for the main buttons and screws. Unfortunately, without buying one I cannot make a model specifically for that one. It works with Scimitar RGB Elite, and should work with…
Hi after purchasing an orange bobiba for prusament, I was struck by the beautiful honeycomb pattern perforated on the sides. As I could not find a solution to comfortably store the filament with the third-party clips protruding from the…
Diameter and weight 2wall loops 15% infil- Star1 small 118mm, 11g Star1 big 153mm, 20g Star2 small118mm, 10g Star2 big 153mm, 20g HolderA 19mm, 9g HolderB 32mm, 12g HolderC 42mm, 20g
I added holes for some tungsten weights to keep it from sliding around as much.
A modified left mount that fits the BLTouch/probe on the inside of the mount. This reduces the distance from the nozzle, decreasing the x/y runoff needed to probe the whole bed. x_offset: -20 y_offset: -17
Adjusted X Carriage to work with Rapido UHF and the HGX Lite V2 Extruder mounting holes.
Easy ruler for reading how much weight is on the Eisenlink Adjustable Dumbbell (https://www.amazon.co.uk/dp/B0BZHHCSFD) The left side of the ruler measures when only the 2kg plates, are used. Read the right hand side when 2 x 1kg plates…
The elements allow you to attach guy lines to a light antenna mast. The ability to rotate the mast has been retained. The model is adapted to a foldable "flag" mast with a diameter of 51 mm. I printed with Pet G, 25% infill. Elementy…
Introduction Weightlifting disc with 50mm hole for Olympic Weightlifting and Powerlifting Bars. Fits every normal barbell you find in gyms. How to assemble Print the two parts with the desired infill and add the rest as rapid concrete to…
This 3D-printed battery holder is designed to securely hold six 21700 lithium-ion cells in a 3S2P configuration . Delivering 11.1V nominal output, it’s perfect for compact and lightweight battery builds, whether you're working on RC…
I bought a stylus to enter directions on my phone while biking with gloves on. This is mostly useful in the winter. I didn’t like the original double-sided tape mount, so I designed a simple 3D-printed handlebar mount instead. It snaps…
Make for 3d Nozzle only its not short stroke shoot faster less recoil less consume gas My setting wall 5 ,infill 20 ,ABS ABS lightweight than PLA+ but ABS weaker than PLA+
I printed out the Rift laptop stand and liked it but wished it was heavier. So I modeled up an adjustable laptop stand that can be filled with whatever you want, I chose lead shot because it was much heavier than sand or concrete and…
3 parts print(total 5), Drawer storage scalable to accommodate various items. easy to assemble and mount on any overhang surface. Print compatible with minimum support printing.
Using little stones, marbles or similar, you can adjust the weight and sinking speed of this diving ring. There are three options available: Magnetic: Everything is held in place using 6x2 mm magnets. Depending on the magnets strength,…
After successfully releasing my 2-in-1 printhead and receiving many requests for a single-extruder version compatible with Trianglelab-mount hotends , I decided to design and share this upgraded printhead with you. This lightweight,…
This simple yet effective container is designed to fit perfectly in any standard bike bottle cage. The lightweight PETG construction combined with a flexible TPU lid makes it ideal for carrying small essentials on your rides. What You…
Experience the joy of pure driving with this 3D printable STL model of the Mazda Miata MX-5. This iconic lightweight sports car model is perfect for automotive enthusiasts and roadster fans looking to display the legendary handling and…
This design is optimised to use in the sportsman 150g class, needs a flex frame printed in TPU while all the other files tagged as RIGID can be any material of your choice, we suggest PLA-ST for use in the full combat class. designed to…
Here's a universal lens support bridge for the Arri LWS / Lightweight 15mm standard (60mm spacing on centre). You can use it flipped up or down depending on your needs and your lens diameter. Making this saved me about $400, maybe it'll…
Edit 15/2/2026 Added Back V2.1, with a bigger 7mm rear skate land and a much improved side button(s) holder Added a V2 for the front. USE 1 WALL THICK TREE SUPPORTS Added a scroll wheel support with larger screw holes. Forcing screws into…
Full Image Catalog The complete gallery of my works can be found at www.marjers.com . You can search by the file’s reference number or simply click the preview image to open it directly. This is a high-quality 3D design optimized for…
Explore a new VaseMode technique with dual-wall construction for greatly improved strength and rigidity compared to standard single-wall prints. The two walls are stitched together by a fine textured seam, which makes the dual-wall…
Keep your fishing gear neat and accessible with this 3D printable dropshot weight organizer, custom-designed to fit inside the Plano 3700 tackle box . It may fit the Plano 3750, but I haven't tried it. No more digging through a tangled…
UPDATES 11/16/25 Added versions of both cooling ducts for the smaller 4.1-4.5mm wide heat inserts. This is a lightweight fan duct based off of my original cooling duct design for the Qidi Q2. The duct with both heat inserts and bolts…
Updated 01.25.26: Increased tolerances to accommodate different materials. This is an 8 point shuriken ninja throwing start that allows you to add a US quarter in the center for weight. The cap can be removed using tabs to retrieve the…
Full Image Catalog The complete gallery of my works can be found at www.marjers.com. You can search by the file’s reference number or simply click the preview image to open it directly. This is a high-quality 3D design optimized for…
Full Image Catalog The complete gallery of my works can be found at www.marjers.com. You can search by the file’s reference number or simply click the preview image to open it directly. This is a high-quality 3D design optimized for…
As seen at CFT, BPOC, Rag and NSNW in 2025, my take on a minimalistic Lynx shroud. Compatible with the excellent Remnant pump geometry by Chance, this shroud is designed to be as light as possible while still providing the necessary…
Trays for either (1) or (2) Samsung Remotes. The lower tray that holds (1) remote is designed to have a cavity for adding weight; rocks, sand, nuts/bolts, etc. Then you can glue it shut. My remote models are BN59-01480A (black) and…
Since Hubmotors are very usefull for combat robots, but only existed for 450g weightclasses and up, I created one that can be built from a 2202 brushless motor and only weighs around 35g (including mounting screws). You can get it down to…
No you are able to fill those pesky holes while using less filament. Also, the bottom layer looks better than the top layer. Print upside down for best results 5 percent infill, no strength is needed.
The original design idea came from needing to suspend a specific amount of weight from another object.
A paint brush stand that does not fall over easily. The bottom part is hollow and can be filled with sand, the lid snaps shut but a few drops of glue does not hurt. Prints in separate pieces and glues together. The stalk comes in 2…
Holder for Xdeep's horrible drop weight design. They dry fit fine but haven't dove with them yet. will update once I do.
Hier geht es um eine sehr kompakte 2,8 Zoll Drohnen Frame das spontan entstanden ist. Das Frame gibt es dann in den Größen 2,5 / 2,8 / 3 Zoll. Ich habe auch noch zwei 3,6 Zoll Version erstellt um dann auch noch meine 3,6 Zoll Drohne…
Update: Model updated for a cleaner exterior surface. No functional changes. These oversized, functional bookends are designed to solve one of the biggest problems with 3D-printed bookends: they’re usually too light to actually work. This…
Threw this together in TinkerCAD super fast because I have no clue how to design with real CAD programs. Wanted something without magnets as I'm not a fan. The stock screws work well now, just make sure you screw them in and out a couple…
Variants of the parts by Ilyas Sofian. - Lighter baseplate with cutouts - Comfort groove on the mouse clicks. Also 1mm extended for more travel clearance. https://www.printables.com/model/811624-logitech-g1008-mod-g703-shell-g305-pcb
This 53g record player weight is a must have for record collectors. It prevents vinyl from warping and vibrating when it is being played. Simplistic yet effective design.
The RatRig VCore 3.2H XY Joiner comes with the VSlots on the model - I have a lightweight gantry that doesn't have VSlots - so I've remixed the official model from RatRig and removed the VSlots - fits most Lightweight Gantries. My gantry…
Manfrotto Handle for the 3.4 Kg black weight with M8 screw and bold
Features: 10 by 10 inches (scale down in slicer for smaller sizes) Flies 35 to 50 feet 20 grams of PLA One part No supports needed! Usage: Pinch behind wings Adjustable flaps for optimal preformance Bend front wing flaps down and back…
I liked the concept of the "Olympic Barbell Vertical Wall Mount" so much that I wanted to modify it to fit some of my training weight bars. It was scaled down in size as the bar only weighs 7kg and modified it to fit M6 screws I wanted to…
This design was made for Canberra Combat Robotics and the starter kit we sell, if you are finding this design yourself you should still be able to make it work with general antweight parts. The weapon is intened to be a foam spinner, i…
This model replaces a standard shopping cart coin — no more digging through your pockets. It prints in just 13 minutes and uses only 1.29 g of filament . ✔ No supports required ✔ Very easy to print ✔ Lightweight and practical ✔ Can be…
To hold down sewing patterns while cutting the garment, I am using large-size washers for M16 and bigger screws. This is a simple design to stack them on top of each other. Simple and fast print. Print as shown in the 3MF in PLA or any…
This design was made for Canberra Combat Robotics and the starter kit we sell, if you are finding this design yourself you should still be able to make it work with general antweight parts. I have attached the Fusion 360 project file for…
Introduction If you use your Hario Polaris scale for pour-over coffee, you might have noticed the weight reading "drifting" or changing slightly even when nothing is being added. This is a common issue caused by the high heat of the…
A nice little visual representation of your personal record(personal best) in lifting.
These arrow fins are designed to simplify fletching by eliminating the need for precise alignment and messy glue. The model consists of a thin cylindrical sleeve that slides over the back of the arrow shaft, with three integrated fins…
It will require supports near the bottom of the main part and the little cap could use them as well. I made this because when I feed filament out of my dryers the spools lifts off the rollers when they get light and this usually causes…
This truck/bogey set can be printed out in multiple materials, snapped together without hardware or glue, and can use generic plastic or metal wheel & axle sets. There is enough side-play in the axle sets to allow it to navigate standard…
A CSM Heel Weight for approx. 500g or lead ball bearings. I also wanted something a bit more aesthetic for myself than the solutions I looked at. Print with 4 walls, 15% rectilinear infill, 5 top/bottom layers in PETG or PLA+ - examples…
Fantastic hook modelled by Tmpx64 ! Print Solid, 100% infill in PETG - Scaled in height and thickness to work with my heel forks and heel weights. 1cm thick, 2inch x 1inch. Please download the original model as well!
Two inserts with caps introduced for inserting weights used to balance car wheels
A tablet weaving frame-style loom that builds onto two two-foot sections of PVC. My preferred setup is to place the curved crossbar so the retaining screw holes are at the eighteen inch mark, leaving roughly five inches of pipe sticking…
WARNING: UNTESTED I haven't printed it as my mouse hasn't arrived yet, so I'd be happy to get some feedback in the meantime! I am by no means a designer, just a tinkerer, so this could be rough.
this model is made for a trx4m high trail if you want to sled pull or just need weight on the front of your truck or you think it looks cool (if you want a bronco/defender one leave a comment i'll make one)
Fits around a 2" pipe and holds a common barbecue grill piezoelectric igniter. For use as a lightweight trigger on a spud launcher. Category: Engineering
Keep your living space organized with this sleek and sturdy wall mount designed for two Sony remote controls. This model is optimized to be lightweigt to save filament, yet strong enough to hold your remotes securely. 2 Versions included:…
Keep your living space organized with this sleek and sturdy wall mount designed for remote controls. This model is optimized to be lightweigt to save filament, yet strong enough to hold your remotes securely. 3 Versions included: -1:…
Keep your living space organized with this sleek and sturdy wall mount designed for remote controls. This model is optimized to be lightweigt to save filament, yet strong enough to hold your remotes securely. 3 Versions included: -1:…
This is a counter weight jig for 2025-2026 Science Olympiad Machines event, useful for actively adjusting the position of a counter weight for a machine. This object does need supports. Height is 9.4 cm, width is 2.5 cm, length is 5.5 cm
Base and lid for a weight casing that can be used to slide inside of any 3" diameter tube. The amount of clay can be adjusted to create different weight blocks. These are useful to use in model rocketry to add weight to the rocket in a…
It's a sign in which is made to promote weight loss viral on TikTok
Features Weighted - if you choose that option. There is an internal cavity designed to hold 12 1/4 oz wheel weights. See links below for purchase. Offset Heights - The back holder is 2mm higher than the one close to the drip tray.…
This is a recreation of a rubber part which connects the adjustable tracking force weight to the end of the tonearm on certain Akai turntable models from the 1980's. The original rubber part is over 40 years old and is often found in a…
I find I have all kinds of straight metal, wood (rod) pieces lying around. They can be stored upright, but I hate that method, so I developed this quick wall mount system. You can see them at a glance. This could be developed way further.…
A somewhat-improved version of my earlier 3d-printed tablet-weaving loom: smaller, less blocky, packs flat, and doesn't require external clamps. Notes: Print 1 of each piece, with the exception of knurledScrew (4 pieces), support (4…
To hold the lid shut, i used the tiny magnets from Dexcom G7 Sensor applicators but you can also get a bunch of 5 x 1.5 mm magnets on AliExpress. For the hinge bolts i used the threaded ends of 2 mm bicycle spokes. I mounted them by…
What better spoils of war than a skull to keep your documents in place?
In the early model A1, A2 and A3 platform VW Rabbit, Scirocco, Jetta, Convertible and Pickup/Caddy models with the 020 transaxle, adding weight to the longer sift rod can help improve shifting feel. In fact, so much so, that in the A3…
Finally, a training butterfly knife that actually lets you adjust the balance and weight to match your skill level and preferences. Unlike standard practice balisongs, this print-in-place model features M5 screw ports in the handles and…
This is a universal 75x75mm stability mount designed to add a solid foundation to top-heavy decorative prints. While it works for various models, it was specifically custom-fitted for the Rose Decor by 29flo to prevent it from tipping…
🔋 Ultra Lightweight 18650 2S2P / 4S Battery Holder This is a lightweight 18650 cell holder designed for high performance applications such as: • RC jets • FPV drones • Electric airplanes • Robotics • Compact high current battery packs The…
🔋 Ultra Lightweight 18650 6S Battery Holder This 6S 18650 holder was designed specifically for high performance applications where weight and rigidity matter: • RC EDF jets • Long range FPV aircraft • High voltage drone builds • Robotics…
There are two versions of the rack: with a "MAX 65°C" reminder text embossed in the wall (intended to be printed in PETG) and a version without any text. Line width: 0.5 mm (the walls of the model are exactly 1 mm thick). Layer thickness:…
None of the different counterweights tell you what diameter of bar thaty are intended for, I bought a Sky-Watcher 11-Pound Counterweight for AZ-EQ6 for my AM3 because ZWO doesn't sell a counterweight, turns out it has a different diameter…
This model consists of 3 parts. Please download .3mf file for getting separated parts Body with Base Plate Player Head Weight Bar If you wish to print this in single piece, please download STL file. Supported should be given. Use Bambu…
Elevate your coffee game with this Adjustable Coffee Leveling Distributor . Easily set the depth for perfect, even grounds before tamping, ensuring consistent, rich espresso shots. Adjustable Depth: Customize from 5-10mm. Even Grounds…
I created this CrossFit model as the ones I saw online were all in kilograms and my friend wanted one with weight plates in pounds that matched the colors used in her gym. The bars are made from a 3/16" dowel (sharpied black), which costs…
Printed in PLA on Prusa Core One. Should fit regardless of printer type, as long as dimensional accuracy is decent. Tolerances are a bit tight on the rail for a good snug fit. Cad files are at…
Add sand or lead shot to turn this into a weighted dryfire mag insert. I used #8 shot for about 150 grams. An average 9mm round is between 10 and 12 grams so I can emulate a 10 to 12 round magazine. Should work on any double stack mag.…
A lightweight Base Plate for Mega Bloks, perfect for building a play table! Includes countersunk holes for mounting with #6 Screws. Layer: 0.28mm Infill: 10% gyroid Bottom Layers: 2 Top Layers 3
A fully 3d-printed lightweight package opener.
I needed extra weight on a gas-cylinder based monitor mount to prevent it from drifting upward. So I whipped this up in CAD and sent it off to Send-cut-Send to be water-jetted in mild-steel or whatever was the cheapest and densest…
A spool that uses universal mesurments to be able to use refils, print the 2 sides and then the 3 middle parts, screw in the first 3 parts with one side then place the refill inside then add the second spool part and screw in 3 more…
Truth Or Dare Dice Weighted: This dice has a 60% chance of landing on “dare,” so people who always pick truth will get many more dares. No supports. 60% chance on landing on dare. Print time: around 1 hour. Thanks for all of the support!…
A simple lightweight putty knife to fill holes and more! About <30min print-time.
Upgrade your walls with this ultra-strong, single-screw PETG wall hook – designed from the ground up for real-world heavy use! Printed in durable PETG, this hook laughs at weight that would snap lesser prints. It securely holds towels,…
Weight Spring Clip Cover Flashforge AD5M(0.4 Nozzle), Overture PETG Print Time= 25mins Total Filament= 8.38g, 2.74m Print Instructions Layer Height = 0.2mm Wall Loops = 3 Infill = 50%, Gyroid Any and all feedback is welcome and appreciated.
Saves ~3,8g compared to og base, my one is about 2,9g after messing with the print settings. The screw placements and other are not exactly right but the pcb will fit U can use the design however you want but no selling
![VESA weight for monitor arm [700g or 1.5 pound]](https://media.printables.com/media/prints/d8cddf67-c6a9-49f5-a026-a546be8043d8/images/12343032_706cffb2-eb20-4a86-adcd-549ef83888e3_6e546d1a-505d-40a8-869e-ff0aa1d03560/img_20260318_142914583_hdr_ae.jpg)
