Senserion Sen55 ESP32 (+Seeed Grove Multichannel Gas sensor) Case
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Case for Sen55 module, a fan, ESP32 and USB C power breakout board.
- Rating
- 0 / 5
- Likes
- 8
- Downloads
- 59
- Makes
- 0
- Views
- 1,095
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Engineering
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
A simple case design (shell + tray + cap) for a Senserion Sen55, ESP32 D1 Mini (or XIAO ESP32 C3 or S3), Seed Studio Multichannel Gas Sensor v2, USB C power breakout board and a Noctua NF-A6 PWM 5V.
I made a more in-depth blog post for this project here: Link
BOM
Sen55 only:
- Sen55 Module
- JST GH breakout cable
- Noctua NF-A6-PWM 5V
- ESP32 D1 Mini or Seeed XIAO ESP32-C3 (or S3)
- USB C breakout board (to get power to the different components without overloading the ESP)
- M3 Heat-set inserts (for Fan)
- 2x M3x8 Screws (can be longer though)
- some VHB Tape (to mount the ESP and USB C boards)
- USB C Power supply (can be as little as 1A)
Sen55 + Multichannel Gas:
- All of the above
- Seeed Grove Multichannel Gas Sensor V2
- M2 Heat-set inserts
- 2x M2x8 screws
The Build
All parts need to be printed once per build (1x Shell, Tray and Grill). This project can be done without soldering wires, but that is not how I planned it, or built it.
Why add a fan? The Sensor would be re-using its own air if there was no “powered” air stream pushing new air in, old air out. Senserion advises to use the sensor if the Air around it is traveling at less than 1m/s, which is why the fan is at 25% and not higher. Enough to move some air, not enough to blow itself around.
Before building the unit itself, I'd suggest flashing ESPHome on your ESP board and making sure it works, as the assembled Unit doesn't use the ESP's USB connector. This'll save you having to take the whole thing apart again.
- Cut the Fan plug off, wire the Positive and Negative wires to the Breakout board, and the PWM wire to the ESP32 (use any pin that isn't reserved).
- Cut the breadboard connectors off the JST cable for the Sen55 unit. Positive and Negative power leads also go to the breakout board. Wire the remaining pins to the ESP (except for the last one, that needs to be cut off, check Senserion's installation instructions)
- If you are putting a Gas Sensor in here as well, cut the wires so they aren't too short or long to fit into the case. Wire power and ground to the breakout board as well, SDA and SCL also go to the ESP. These can be separate pins with a separate I²C Bus, or they can be soldered to the same pins as the Sen55.
- Remove support material from the tray print (clean up the areas around the Sen55 mounting spot, it's a really tight fit)
- Press the heat-set inserts into the Fan (and the holes in the side wall if using the gas sensor as well)
- Install the Sen55 unit on the tray
- Install the Fan on the tray
- install the Gas Sensor on the side of the tray
- Plug in all the wires, strip them, solder everything to the ESP and USB C boards
- Put VHB Tape on the underside of the ESP and USB C boards, install in their respective locations on the Tray
- Slide the tray into the shell (if it doesn't fit, deburr the bottom edges of the tray, or the wall)
- Make sure the USB C port is visible in the hole at the back
- Add the intake Grill (optionally, this can be superglued in, I wouldn't recommend it in case you have to disassemble the Module, it should friction-fit)
- Plug everything in
- Check readouts in Home assistant. If things don't show up, check soldering/broken wires
Models
There are two versions of the project - the first one with a mounting location for the Grove Gas Sensor, the second one with only the Sen55 unit. Regardless of the version, the first iteration of the Grill wasn't as good as the second version, so I'd use that instead.
I recommend printing with supports enabled, or the overhangs above the Sen55 mounting spot will sag (making it impossible to mount the Sensor). This part of the model came from Senserion, it wasn't designed to be printed in this Orientation. On V1 (with Gas sensor), only the bottom supports need to be removed, the part above is dead space.
All parts were printed on a Prusa XL (with multicolor, the .3mf file has modifiers saved in it), 0.2 SPEED profile with supports enabled.
ESPHome and Home assistant
I designed this little thing to report sensor data back to Home assistant, but it can run Arduino code just fine, no Home assistant needed.
The configuration that I used is as follows:
(basic ESP config above)fan:
- platform: speed
output: casefan
name: "Sensor Fan"
speed_count: 100
output:
#Fan output
- platform: ledc
id: casefan
pin: GPIOXX
frequency: "25000 Hz" Fan runs at 25% by default, can be increased
min_power: 25%
max_power: 100%
#neat but not necessary
time:
- platform: homeassistant
id: homeassistant_time
button:
- platform: restart
name: "AQS - Restart"
i2c:
sda: GPIOXX
scl: GPIOXX
scan: true
sensor:
- platform: internal_temperature
name: "Internal Temperature"
- platform: sen5x
id: AQS
pm_1_0:
name: " PM <1µm Weight concentration"
id: pm_1_0
accuracy_decimals: 1
pm_2_5:
name: " PM <2.5µm Weight concentration"
id: pm_2_5
accuracy_decimals: 1
pm_4_0:
name: " PM <4µm Weight concentration"
id: pm_4_0
accuracy_decimals: 1
pm_10_0:
name: " PM <10µm Weight concentration"
id: pm_10_0
accuracy_decimals: 1
temperature:
name: "Temperature"
id: temp
accuracy_decimals: 1
humidity:
name: "Humidity"
id: humidity
accuracy_decimals: 0
voc:
name: "VOC"
id: voc
algorithm_tuning:
index_offset: 100
learning_time_offset_hours: 12
learning_time_gain_hours: 12
gating_max_duration_minutes: 180
std_initial: 50
gain_factor: 230
nox:
name: "NOX"
id: nox
algorithm_tuning:
index_offset: 1
learning_time_offset_hours: 12
learning_time_gain_hours: 12
gating_max_duration_minutes: 720
std_initial: 50
gain_factor: 230
temperature_compensation:
offset: 0
normalized_offset_slope: 0
time_constant: 0
acceleration_mode: low
store_baseline: true
#address: 0x69
update_interval: 10s
#Seeed Grove Sensor
- platform: grove_gas_mc_v2
nitrogen_dioxide:
name: "Nitrogen Dioxide*"
ethanol:
name: "Ethanol*"
carbon_monoxide:
name: "Carbon Monoxide*"
tvoc:
name: "Volatile Organic Compounds*"
#Seeed Sensors take a while to calibrate, marked with *
Omit the last block if you are not using the Gas Sensor.
Happy building!