1 / 6
Knurled Hand Grips for the Daytona Harbor Freight Car Jack & Others — image 1
1 / 6

Knurled Hand Grips for the Daytona Harbor Freight Car Jack & Others

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

A few handle designs for the Daytona 3 Ton Long-Reach Car Jack from Harbor Freight or others ~Read Description~

Rating
0 / 5
Likes
14
Downloads
23
Makes
0
Views
152
Reviews
0

Updated at source:

Model information

Category
Automotive
License
Creative Commons — Attribution

UPDATE:  NEW INTERNAL CLAMP STYLE ARE EXTREMELY EXPERIMENTAL    NOTHING HAS NOT BEEN TESTED YET!, WHEN I TEST IT AND CONFIRM WORKING, I'LL REMOVE ALL OF THIS BETA STUFF AND WARNING. Same M10 as stated below can be used if you are feeling brave and want to give it a try, there is a test file before.  No supports are needed for this clamp.
 

This is the jack this model is designed for:
https://www.harborfreight.com/automotive/jacks-jack-stands/floor-jacks/3-ton-long-reach-low-profile-professional-floor-jack-with-rapid-pump-green-64785.html
 

Update #1:  I added a small cutout for the Inside Diameter.  This will help ensure the Seam from the print doesn't interfere with the diameter, this will give the Seam a place to go.  You can use the Preview Window in your slicer to confirm that the Seam will be located in that cutout.  If it doesn't, then you will need to adjust the Seam Position in your slicer settings.

 

A few handle grips for the handle that attaches to the car jack. 
Things that are included:

1.  Internal Clamp, (optional)
2. Bolt Cover, (optional, for the bolt that drives the internal clamp)
3. Multiple Variations

It is highly recommended to print these in TPU at 10-15%, .2 layer height, (so it can be a little squishy for grip). If you decide to use a different filament other than TPU, just note, the clamp might be mandatory due to the plastic being too slick.



I'm not sure how the tolerances are from handle to handle, so I included this little chart to help with scaling and sizing, (this will make it a lot easier to size correctly, especially if you measure your handle with mics/calipers). It is also recommended to scale only in the X and Y direction. 
If you decide to use one of the bolt covers, make sure to scale it the same amount as you did your grip.

Chart:     The size of the handles may vary from one jack to another.  Use the Test Piece included to figure out the scale you need first, then apply that same scale value to the grip to save filament. 
100%   =   33.200mm
101%   =   33.532mm
102%   =   33.864mm
103%   =   34.196mm
104%   =   34.528mm
105%   =   34.860mm
I included a photo on how to check the diameter after you scale the model, (I'm using Bambu Studio and the name of the photo is “Measuring Example”).  Where you would normally think you would check at the top of the bore, is difficult, the slicer doesn't like to select it, so you have to go further down inside the Inner Diameter and click that diameter to check it.   I recommend to go slightly smaller,  -.100 to -.150mm roughly, of what you measure with your mics/calipers to give it a sort of compression fit. 



For the Internal clamp, I used an M10 bolt and nut. My bolt was 60mm long, but if you find that your nut doesn't fit the cut out included in the bottom mount, you can use a longer bolt, and then just print the upper mount twice, flip one of them to oppose each other, and use the clamp that way.  The “Top Mount” is recommended to be printed in TPU for extra squish when clamped to help grab the walls of the handle. You can try to print the bottom mount in TPU, but it will be very difficult to remove the needed supports, (for the pocket for the nut).

Tags