Desk work lamp

Precision made desk lamp for finest work, but also as ambient light or bed lamp.

Precizně zpracovaná stolní lampa pro práci, ale také jako ambientí světlo nebo k posteli.

Specifications / Specifikace:

------------------------

Assembly / Sestavení

Materials and Tools:

• 1x Philips Light Bulb, EXACTLY this model
  EAN: 8720169324190
  Specs: 9.5W; 1055lm; EEL - E; A60; E27
  Any other model is not tested and Lamp Shade may need some modifications
• 4m 2x0.75Cu Cable
• 15x21mm Rocker switch
• Europlug (non-polarised)
• Alu pipe ø10x1mm - 2600mm
• Faston 4.8mm - 3x female; 1x male
• Shrink wrap ⁓4.8mm - 4x 20mm
• Cable ties 100x2.5mm - 9x
• Rubber pad 1mm - cut out 1x ø26mm; 1x 35x35mm
• M3x15 Philips - 2x
• M4x25 Philips - 6x
• M4x30 Philips - 1x
• M4x50 Philips - 2x
• M6x40 Hex - 1x
• M6x50 Philips - 1x
• M10x60 Hex - 1x
• M3 Nut - 2x
• M4 Nut - 9x
• M6 Nut - 1x
• M6 Wings nut - 1x
• M10 Nut - 1x
   
• Philips Screw driver
• (Cordless) Drill
• 10, 6, 4 and 3mm HSS drill bits
• Pliers (Cutting, Universal, Crimping)
• Tweezers
• Lighter
• Knife
• Small flat Screw driver
• Super Glue
• Permanent marker

Assembly Guide:

Preparation

1.  Print instuctions:
    - Material: PETG, ASA, ABS, but Definitely NOT PLA
    - Infill: 50%
    - Clip parts separately, Hinges parts separately, Shade separately
    - Supports only on the Lamp Shade (import as project)
2. Redrill all holes on all hinges parts
3. Cut alu pipe: 2x 500mm; 2x 800mm
4. Put all parts with screw holes on pipes ends
   - 800mm is upper arm
   - 500mm is lower arm
5. Mark Screw holes and drill all of them with 4mm drill bit

Clip and lamp base

1. Take Clip, and glue M10 nut in the designated hole.
2. Now take M6x40 Hex bolt and put it into designated hole on the opposite end
3. Cut the rubber pad (1x ø26mm; 1x 35x35mm)
4. Glue the square piece over the M6 bolt (from the Clip's inside)
5. Glue the round piece onto Screw end
6. Glue the Handle onto M10 bolt
7. Screw the M10 bolt into the Clip
8. Take Screw end base and glue it onto the M10 bolt
9. Put Screw end into its glued base

Lower arm

1. Take the lamp base and put it on the M6 bolt on the clip
2. Put M6 nut onto the bolt, tighten it to your liking
   - To prevent it moving with the base, glue the nut on the bolt
3. Put 500mm pipes into designated holes and align the screw holes
4. On the opposite end, put a Lower arm hinge
5. Now use M4x30 bolts on base and M4x25 bolts on hinge and tighten them

Upper arm

1. On one end of 800mm pipes, put a Upper arm end
2. Now slide Telescopic hinges on both pipes
3. On the opposite end, put Upper arm hinges on both pipes
4. Now use M4x50 bolt and tighen it up

Lamp shade

1. First, take the Light Bulb and open it carefully
2. Take small flat screw driver and take out the LED base (as shown on image bellow)
3. Drill 3mm holes into the square holes on the LED base
4. Take the Lamp Shade and its hinge, M4x30 bolt and put them together
5. Take the Cable and pull it trough hole on the Lamp shade
6. Crimp female fasto connectors on both wires and put the shrink wrap over both of them
7. Crimp the female faston onto hot wire on LED base and male onto the neutral
   - Don't shrink the whole wrap on the male one, leave the connector itself unshrinked
8. Plug the neutral fastons into each other
9. Take M3 screws and carefully put them into small holes inside of the shade, use tweesers
10. Now put the LED base into the shade and tighten the M3 screws
11. Plug hot wire fastons into the switch (through the switch hole) and put it in.

Final assembly

1. Take the M6 Philips bolt + wings nut and tighten Lower and Upper arm together
2. Take the M4x50 bolt, allign screw holes ofLamp shade fixture and lamp itself and tighten them together.
3. Take cable ties and set telescopic range with them to your liking
4. With the rest of them, attach the cable to the lamp itself, leave enough cable next to the shade and between the arm hinges, so it can move freely.
   - Next to the lamp shade 1x
   -Next to the telescopic range limit 1x
   - On both ends of the bottom arm 2x
   - On the lamp base 1x
5. Wire the europlug