Motorola Edge 40 Pro Case/Cover/Bumper (Moto X40)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Case/Cover and Bumper for Motorola Edge 40 Pro (Moto X40) with possibility to insert magsafe.
- Rating
- 0 / 5
- Likes
- 6
- Downloads
- 142
- Makes
- 1
- Views
- 563
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Portable Devices
- License
- Creative Commons — Attribution
If this model meets your highest expectations consider to donate. It took around 20 hours of work to perfect and make all the variants.
Important: print settings
Disclaimer, this is a really hard print (steep overhangs with flexible material, especially in the first layer. If you've never printed a flex material calibrate your printer properly or this won't print well at all. By printing tests I've gathered some insights on some important settings you should consider.
I'm using orcaslicer so you'll find the corrisponding setting if you use that. Similar options are present in all slicers.
Nozzle size
This print is generally optimized for 0.4mm nozzles, especially using 0.44 line width on all lines.
Quality
Layer height: 0.2 mm (everything in the design is tuned to this)
Line width: 110% or 0.44mm
Wall generator: arachne (makes for better printing especially in the button portion as it's an odd line width)
Walls printing order: Inner/Outer (slightly worse finish but better overhangs, essential for this print)
Avoid crossing walls (limits stringing)
Only one wall on top/bottom surface: off (this will make your first layer worse, can be turned on for the last but i wouldn't recommend
Detect overhang walls: true
Extra perimeter on overhangs: true (again, helps with overhangs)
Strenght
Wall loops: 3 at least
Ensure vertical shell thickness: true
Speed
Your calibration should work, but I'll state it here, you're probably going faster tha you should. Consider also max volumetric speed, mine is set to 3. By going slower you're going to get much better quality, I was printing at 40mm/s with pretty bad results, the following settings helped:


Supports
With these settings, supports will come off by pulling hard, if your overhangs are tight nothing will come off with them.
Type: tree
Threshold angle: 30 (I i usually do 25 but this seemed to help better with first layers overhang)
On buildplate only: false (you want some trees in the most critical part. comes off pretty easy with needle nose pliers)
Remove small overhangs: false (interferes with the design)
Top Z distance: 0 (tpu sags a lot so tighter is better)
Top interface layers: 0 (interface layers don't work well with tpu, and the thin bridges nature of this cover makes the tree pointy tip much better)
Don't support bridges: false
Design variants:
Slim with camera guard (suggested)
1.76mm all around thickness. Back side has 1.4mm thickness to perfectly fit a magsafe shape (bought 5 for 2 euros on aliexpress .5mm thickness, i used a .6 slot to insert them, leaving 2 layers on bottom and on top).
This thickness is great in the borders and optimized in the back of the case to use as less material as possible. The guard has to be printed separately and clips in place (I've printed it of a harder material such as pla and petg, it's also an accent piece that makes for cool color combinations as seen in iphone cases here on Printables).


Case (simple)
2.64 thickness all around, bottom thickness 2.6. Camera doesn't touch flat surface. Extra protection from the added thickness
Bumper
Same as the Simple Case version but minimal backing. Saves filament, print time, and feels great in the hand, similar to the feeling of not having a cover.
Magsafe insertion
Insert this model as a negative shape in the center of the case (doesn't work for the bumper for obvious reasons). My recommendation is not to go below .4mm from the bottom surface so it has proper padding to be embedded and still work.
Design features:
Ridged power button

Clicky side buttons
Comparable to 80% feeback compared when without cover

No supports for side buttons

