1 / 12
Qidi Q2 — Cooling Duct (v5.1 & v6.0 Dual-Flow) — image 1
1 / 12

Qidi Q2 — Cooling Duct (v5.1 & v6.0 Dual-Flow)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

CFD-optimized cooling duct for superior overhangs and bridging on the Qidi Q2.

Rating
4.769 / 5
Likes
468
Downloads
2,226
Makes
46
Views
10,237
Reviews
39

Updated at source:

Model information

License
Creative Commons — Attribution — Share Alike

Qidi Q2 — Performance Cooling Duct (v5.1 & v6.0 Dual-Flow)

Summary

A high-efficiency part cooling shroud for the Qidi Q2.

This duct was precision-engineered using CFD (Computational Fluid Dynamics) to reduce turbulence and provide a focused airflow exactly around the nozzle area, improving overhang performance and cooling consistency during high-speed printing.


🌪 CHOOSE YOUR VARIANT: v5.1 vs v6.0

  • Option A: v5.1 — Classic High-Flow
    Single unobstructed internal airflow path, optimized for maximum raw air volume. This is the original proven design.

  • Option B: v6.0 — Balanced Flow Redesign

    • Redesigned Inlet: The fan intake position has been shifted and optimized to feed the internal splitter.

    • Internal Splitter: An aerodynamic divider splits the airflow directly at the inlet.

    • Balanced Static Pressure: The redesigned internal geometry provides more balanced pressure between the left and right ducts.

    • Result: More symmetrical cooling, especially useful for models where consistent overhang quality is required on all sides.

Note on Spacers for v6.0:
The v6.0 duct remains backwards compatible with the original v5.1 spacers.

However, new “V2 for V6” spacers are included with a refined design that better matches the updated inlet geometry. I recommend using the new version for the best fit and appearance.


🚀 KEY FEATURES

  • CFD Optimized: Internal geometry was refined to reduce dead zones and improve airflow through both channels.

  • High-Temperature Clearance: Increased clearance from the hotend compared with earlier prototypes to reduce direct thermal exposure.

  • Pre-designed Supports: The new v5.1 raw.stl includes integrated, easy-to-remove supports.

  • Lightweight & Rigid: Optimized for fast toolhead movements without unnecessary mass.

  • Dual-Flow Splitter (v6.0): Internal aerodynamic divider improves airflow balance between the left and right channels.

  • CFD Verified Pathlines: Simulation data is included in the gallery to demonstrate airflow behavior and pressure distribution.


🌡 MATERIAL SELECTION

This cooling duct was developed primarily to improve part cooling for PLA, PETG and similar materials, where stronger and more even airflow is useful.

When printing high-temperature engineering materials, part cooling is often reduced or disabled depending on the filament and print profile. In these conditions, the main requirement for the duct itself is simply to survive the thermal load near the hotend without losing its geometry.

There is no single “correct” material for every user and every printing condition.

Choose the material according to its actual heat resistance and the way you use your printer.

  • Below ~80 °C heat resistance:
    Not recommended for this duct.
    Typical examples include PLA and many PETG grades.

  • ~80–110 °C:
    Suitable for normal use, especially when the printer is mainly used for PLA/PETG and similar materials.
    Typical examples: ABS, ASA, depending on the specific grade.

  • ~110–130 °C:
    Provides a better thermal margin and may be suitable for occasional high-temperature printing.
    Examples may include PP-GF and other reinforced materials, depending on their actual specifications.

  • Above ~130 °C:
    Preferred when the printer is frequently used for long high-temperature prints.
    Examples include PA-GF/CF, PC-based materials, PPS and other high-temperature engineering polymers.

Important:
The nozzle temperature is not the same as the temperature of the cooling duct.

A nozzle operating at 300–370 °C does not mean that the duct itself reaches the same temperature. Actual thermal load depends on hotend geometry, clearance, silicone sock condition, chamber temperature, print duration and other factors.

Tested example:
An earlier version of this duct printed from PA6-GF30 was tested during printing at approximately 315 °C nozzle temperature.

Local scorching/discoloration occurred near the hotend, but the duct retained its geometry and remained functional.

The current v5.1 and v6.0 versions have increased clearance from the hotend compared with that early prototype.

Always check the manufacturer’s HDT / service-temperature specifications for your exact filament. Different grades of the same polymer may have significantly different thermal properties.


🛠 PRINT SETTINGS

  • Material: See the Material Selection section above. Choose the material according to your real printing conditions and required heat resistance.

  • Layer Height: 0.12–0.16 mm — highly recommended for smoother internal airflow surfaces.

  • Walls: 2 perimeters — optimized to reduce unnecessary weight.

  • Infill: 20–40% — Gyroid or Grid recommended. Avoid 100% infill to keep the duct lightweight.


🔩 HARDWARE & ASSEMBLY

To ensure proper fit and safe clearance, use the following hardware:

  • 1× M3 × 22 mm screw — Main duct mount.

  • 1× M3 × 20 mm screw — Fan mount.

  • Custom Spacers: Included in the files and specifically designed for mounting the front cladding / external cover.

  • Washer / Shim: Included for the fan mounting to ensure a secure and vibration-free fit.

  • Stock Magnets: Transfer the original magnets from the factory front cladding.

⚠ IMPORTANT ASSEMBLY TIP

Use only Low-Profile (Button Head) or suitable Flat Head (Countersunk) M3 screws.

Standard high-profile socket cap heads, typically around 3–4 mm tall, may interfere with parts of the printer frame because clearances around the toolhead are limited.

Do not judge clearance only by whether the screw head is above the nozzle tip — the nozzle is not the only reference point for the toolhead’s mechanical clearance.

For a detailed step-by-step installation guide with 15 photos, check out the excellent Make by Semtexos.


🌡 IMPORTANT: PID CALIBRATION

After installing the new duct, airflow around the nozzle and heater block changes compared with the stock configuration.

To maintain stable hotend temperatures and reduce the possibility of thermal errors, it is strongly recommended to perform a new PID Tuning after installation.

For Qidi Klipper-based printers:

  1. Open the Fluidd/Mainsail console.

  2. Run:

PID_CALIBRATE HEATER=extruder TARGET=220

Adjust the target temperature to match the material you use most often.

  1. After calibration is complete, run:

SAVE_CONFIG

This saves the new PID parameters.


📂 FILES INCLUDED

  • Duct Bodies: v5.1 Classic High-Flow and v6.0 Balanced Dual-Flow.

  • Spacers V2 for v6.0: Recommended for the updated v6.0 inlet geometry.

  • Legacy Spacers: Compatible with both versions if you already have them printed.

  • Washer / Shim: For fan mounting.

  • STEP Files: Included for ducts, spacers and washers for users who want to inspect or modify the geometry.


⚠ A NOTE ON DESIGN & PRINTABILITY

Further aerodynamic improvements are technically possible, but increasingly complex internal geometry creates significant disadvantages for FDM printing.

More complicated internal channels may result in:

  • Higher risk of print failure due to extreme overhangs.

  • Difficult support removal, with a greater risk of damaging internal channels or mounting points.

  • Higher requirements for printer calibration and material quality.

  • More difficult reproduction for the average user.

The current v5.1 and v6.0 designs represent the practical “sweet spot” between aerodynamic performance, mechanical reliability and printability.

The goal is not simply to create the most complicated airflow geometry possible, but to provide a design that delivers strong real-world cooling performance while remaining reliable and reasonably easy to print and install.

Tags