1 / 2
6S 6700mAh LiFePO4 Field Battery Pack (No Spot-Welder Needed) — image 1
1 / 2

6S 6700mAh LiFePO4 Field Battery Pack (No Spot-Welder Needed)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

This is a high-capacity 6S1P battery pack designed to provide portable power for FPV sessions and outdoor electronics.

Rating
0 / 5
Likes
1
Downloads
8
Makes
0
Views
74
Reviews
0

Updated at source:

Model information

Category
Electronics
License
Creative Commons — Attribution

Context

Lithium Iron Phosphate (LiFePO4) technology is evolving rapidly. While the energy density is slightly lower than traditional Li-Ion, LiFePO4 cells offer a significantly better price-per-kWh and a much longer lifespan (often 2000+ cycles). This makes them the perfect choice for field charging and portable power.

The Project

This is a high-capacity 6S1P (19.2V nominal) battery pack designed to provide portable power for FPV sessions and outdoor electronics.

Specifications:

  • Capacity: 6700mAh / 126Wh

  • Chemistry: LiFePO4 (LFP)

  • Budget: ~€15-€20

  • Design Goal: A "no-spot-welder" build using bolted terminals, accessible to anyone with a 3D printer and basic tools.

Note: This is a raw battery pack intended for use with portable DC chargers (like the SkyRC B6neo) and a battery buzzer. It does not include an internal BMS. The 32700 cells are usually rated for about 1C to 3C (approx 6A to 20A) continuous discharge (In my experience the voltage sags a lot above 1C. This is perfect for charging small 4S/6S flight packs at the field but not an e-bike or a massive inverter.

Bill of Materials (BOM)

  • Cells: 6x 32700 6700mAh LiFePO4 (e.g., from nkon.nl)

  • Busbars: 0.5mm Copper plate (DIY cut)

  • Hardware: 12x M4 stainless steel nuts & 24-36 M4 stainless steel washers

  • Case Hardware: 4x M3x30mm machine screws and nuts

  • Wiring: 12 AWG silicone wire, XT60 connector, 6S JST-XH balance lead

  • Safety: Battery Voltage Tester / Low Voltage Buzzer

  • Filament: PLA (Case/Internal frames) and TPU 95A (Protective bumper)

⚠ Disclaimer & Safety Warning

Lithium batteries are dangerous. Short-circuiting or mishandling these cells can lead to fire or injury. This guide documents my personal build process; if you choose to follow it, you do so at your own risk. Ensure you understand battery safety and polarity before beginning.


Assembly Instructions

1. Cell Preparation

Check all cells with a multimeter. Balance them individually to a storage voltage (approx. 3.2V) before assembly. Connecting cells with a potential difference higher than 50-100mV can cause dangerous current rushes during connection.

2. 3D Printing

  • Print the outer case and the internal battery rings in PLA.

  • Print the protective bumper in TPU.

  • Note: Pause the print or use the hex-recesses to insert the 4x M3 nuts into the bottom case during/after printing.

3. Fabricating the Copper Busbars

Cut your 0.5mm copper plate into 7 bridges:

  • 2x Small: For the main XT60 positive/negative terminals.

  • 4x Medium: To bridge the cells in series.

  • 1x Long: For the middle-end connection.

  • Tip: Drill/punch oval holes in the plates to allow for slight alignment adjustments. Busbars_A4.pdf can help cutting the correct dimensions.

4. Wiring & Soldering (Pre-Assembly)

It is much safer to solder your wires to the copper plates before they are bolted to the batteries to avoid heat transfer to the cells.

  • Clean the copper with an abrasive (sandpaper) to remove the oxide layer.

  • Apply plenty of flux.

  • Use a high-wattage iron with a large tip (approx. 400°C).

  • Pre-tin the plate until the solder flows smoothly.

  • Solder your 12AWG main leads and your 6S balancing wires to the respective plates. Ensure you can pull on the wire firmly without it detaching.

5. Battery Layout

Place the cells into the PLA holders. Double-check the orientation of the polarities to ensure a serial connection (Positive to Negative).

Pro-tip: Cover all terminals with electrical tape during assembly, uncovering only the two you are currently working on. This prevents accidental shorts with tools.

6. Final Bolting

Connect the copper busbars to the threaded cell terminals.

  • Use stainless steel hardware only. Galvanized steel can react poorly with copper over time.

  • Use washers to ensure the plates sit level and have maximum surface contact.

  • Before tightening, ensure the surfaces are clean and de-greased.

  • Safety: Once a busbar is installed, cover it with electrical tape or Kapton tape before moving to the next one.

7. Final Integration

  1. Route the XT60 and balance leads through the holes in the outer case.

  2. Slide the battery assembly into the box. A sheet of TPU is provided in the files to add some cushioning at the bottom but it may not fit depending on how much electrical tape was used.

  3. Solder the XT60 connector to the main leads (if not already done). I used 2 connectors to be able to power my googles and charge at the same time.

  4. Secure the lid using the 4x M3 screws.

  5. Slide the TPU bumper over the case. It should be a friction fit, but a small amount of adhesive can be used for extra security.

Quality Control & Use

  • Use a multimeter to check the total voltage at the XT60 and the individual cell voltages at the balance lead.

  • Charge carefully: Use a charger with a dedicated LiFePO4 mode.

  • Discharge: Since there is no BMS, you must use a low-voltage buzzer connected to the balance lead during use to prevent over-discharging a cell.

Happy flying!

Tags