Prusa CORE One Belt Mother Plucker
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A tool for consistently plucking the CORE One belts for repeatable frequency measurements with the Prusa Belt Tuner.
- Rating
- 0 / 5
- Likes
- 3
- Downloads
- 10
- Makes
- 0
- Views
- 72
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Accessories
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Prusa CORE One Belt Mother Plucker
Because your belt deserves a consistent pluck.
The Belt Mother Plucker is a simple tool designed to make plucking the XY belts on the Prusa CORE One more consistent when checking belt frequency with the Prusa Belt Tuner.
Instead of relying on your finger to pluck the belt in exactly the same way and place each time, the Mother Plucker provides a consistent mechanical pluck. This can make it easier to obtain repeatable frequency measurements when checking or adjusting belt tension.
This tool is intended to standardize the way the belt is plucked so it is easier to set belt tension correctly.
Inspiration
I wanted something that was useful for obtaining consistent resonant frequency of the belts and my finger isn't calibrated enough to do that. I found other printable gauge solutions. However, relying on someone else's gauge wasn't enough to alleviate the "are my belt's tension set correctly?" that kept creeping into my mind. I came to the conclusion that resonant frequency analysis must be the best way to tell if a belt has the correct tension, based on some online research and Prusa publishing the correct Hz values.
Printing
Printed using Prusament PETG with 0.2mm layer height, 15% infill, structural Prusa Slicer settings.
Supports are not needed for both parts.
The tool base can be oriented on a side or the top/bottom face. I prefer the side printing results much more than the top/bottom face orientation. The thin walls result in inconsistent shrinking when printed on the top/bottom face. However, the thin walls work best for installing and removing the tool on the linear rail assembly.
PETG printing on the side should work perfect with an outside brim as the thin walls are under stress, and might warp or lift without a brim or brim ears. Regardless, the print should remain functional with any warping or lifting.
Brim ears can be added in Prusa Slicer by right clicking the part and selecting Add part -> Cylinder. The cylinder X, Y size should be 10-15mm. I had to make the z-position for the cylinders 0.2mm and the size 0.2mm for 1 layer brim ear or 0.4mm for 2 layers. I did 1 layer brim ears in the image below and ended up with a slight amount of lift off, almost perfect.

The image below is the amount of lift off/warping when printing with no brims.

How to use
Familiarize yourself with the parts. The tool base is designed to fit on the linear rail one way, when installing on top of the linear rail or the bottom of the linear rail. There are 2 linear rail screw hole guides printed on one of the tool base walls. This wall should always be facing towards the printer door so the guides lock into the linear rail screw holes. You might have to move the tool base left or right so they lock into the holes.

Install the base on the linear rail as shown in the image below and insert the plucker with the protrusion (plucker mechanism "pointy" part) pointing down for the upper belt (rail top installation) or pointing up for the lower belt (rail bottom installation).

The plucker mechanism should be behind the belt and touching the base like below:

You are now ready to either pull (preferred) or push the plucker at an even steady pace to make the belt vibrate. You don't have to pull or push super fast or super slow, just an even steady pace.

Go to the Prusa Belt Tuner website on your device and, when ready, hold the microphone close to the belt.
Pull the plucker when ready and DO NOT move the device until after you get the reading. The belt tuner app is very sensitive to device movement so moving the device might cause either a bad reading or wipe out a good reading. You should be able to move the belt and insert the plucker with one hand while holding the device close to the belt with the other hand once you get comfortable with the process. My readings have only been off by plus or minus 1Hz so far.

Repeat as necessary when adjusting belt tension.
Step 1-7 are shown for the upper belt installation. Remove the base, rotate 180 degrees left or right, and install under the linear rail for the lower belt. Remember to switch to the lower belt on the Prusa Belt Tuner Wizard!
Compatibility
Designed specifically for the Prusa CORE One/+/L XY belt assembly arrangement.
