Mounting case for XIAO ESP32S3 & Wio-SX1262 Kit
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Enclosure for XIAO ESP32S3 + Wio-SX1262 LoRa kit. Zip-tie or wall mount, antenna bulkhead hole, easy print.
- Rating
- 5 / 5
- Likes
- 7
- Downloads
- 59
- Makes
- 0
- Views
- 251
- Reviews
- 1
Updated at source:
Model information
- Source
- Printables
- Category
- Electronics
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
A simple, printable enclosure for the Seeed Studio XIAO ESP32S3 paired with the Wio-SX1262 LoRa Kit, built for running Meshtastic. Mount it by zip-tying to a pole/rail or screwing down through the side mounting ears, with a dedicated hole for a panel-mount SMA antenna cable so you can keep the radio's antenna outside the box (or relocate it) instead of cramming it inside.
Features
Snug internal fit for the XIAO ESP32S3 + Wio-SX1262 stack.
XIAO Mount.stlis a mounting plate with two columns of small holes down the center, matched to the pin headers that connect the stacked XIAO ESP32S3 and Wio-SX1262 boards, secured inside the case with M2 screws.XIAO Holder.stlis a small clip that helps secure the board stack against the mount — print 2.USB-C cutout for power/programming without opening the case.
Ventilated lid to help the radio stay cool.
Two elongated slots on the back of the case, sized for zip ties, for mounting the whole case to a pole, rail, or similar.
Two mounting ears on the sides of the case, each with a round hole, for screwing the case to a wall or panel as an alternative to zip-tying.
Two corner ears on
XIAO Mount.stl, each with a round hole, used to screw the mount plate down inside the case.A bulkhead hole sized for the SMA connector on a TUOLNK SMA Female to IPX/U.FL RG178 pigtail cable(4"/10cm), letting you panel-mount an external antenna cleanly through the case wall.
Four-screw lid closure using self-tapping hardware.
Print Settings
No special settings needed — prints fine at standard settings.
Minimal/normal supports — only needed for the antenna and screw holes.
Standard layer height (0.2mm) works well; any material you'd normally use for an enclosure (PETG or ASA recommended if it'll live outdoors).
Hardware Needed
Seeed Studio XIAO ESP32S3
Wio-SX1262 LoRa Kit
TUOLNK SMA Female to IPX/U.FL RG178 coaxial pigtail, 4" (10cm) — or similar U.FL-to-SMA jumper
M2 self-tapping screws (mounting the Wio-SX1262 board)
M2.5 self-tapping screws (lid closure)
Assembly Notes
Stack the XIAO ESP32S3 onto the Wio-SX1262 board via their pin headers, then seat the stack onto
XIAO Mount.stl(the header pins pass through its center holes).Fit both
XIAO Holder.stlclips in place to help clamp the stack against the mount.Screw
XIAO Mount.stldown into the case body through its two corner ears using M2 self-tapping screws.Connect the U.FL end of the pigtail cable to the Wio-SX1262's antenna connector, and route the SMA end out through the bulkhead hole in the case wall.
Close the lid with M2.5 self-tapping screws — the USB-C cutout leaves the XIAO's port accessible for plugging in a cable afterward.
Mount the finished case: zip-tie through the two slots on the back, or drive a screw through each side mounting ear.
Files
Body.stl— main enclosure with USB-C cutout, antenna bulkhead hole, zip-tie slots on the back, and side mounting earsCover.stl— ventilated lidXIAO Mount.stl— internal mounting plate with pin-header holes for the stacked boards; screws into the case body via its corner earsXIAO Holder.stl— small clip that secures the board stack in place (print 2)case.3mf— full assembly, all parts pre-arranged for printing