Gecko Futures Jig Completion Kit – 12 mm Makita Base, Timmy 3D Tool & Alignment Target
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Gecko Futures Jig Completion Kit This project includes three independently designed accessories: 1. Makita Router Base –
- Rating
- 0 / 5
- Likes
- 1
- Downloads
- 2
- Makes
- 0
- Views
- 14
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Tools
- License
- Creative Commons — Attribution — Share Alike
Gecko Futures Jig Completion Kit
This kit completes the Gecko Surfboards 8 mm two-pass router jigs for Futures-compatible surfboard fin boxes.
The original Gecko jigs provide the two routing templates, but they do not include a positioning target, a depth and levelling gauge, or a metric router-base setup for a large 12 mm cutter.
This upload contains three accessories:
Makita router base for a 12 mm cutter
Timmy 3D Tool for jig levelling and cutter-depth setting
Removable alignment target for accurate fin-box placement
The original Gecko router jigs are not included.
1. Makita Router Base – 12 mm Cutter
This router base is designed around a Bosch Ø12 × L31.5 × S8 straight router cutter.
Dimensions
Cutter diameter: 12.00 mm
Cutting length: 31.5 mm
Shank diameter: 8 mm
Guide-bushing outside diameter: 21.65 mm
Guide-bushing inside diameter: 14.00 mm
Radial clearance around the cutter: 1.00 mm
Guide wall thickness: 3.825 mm per side
The 21.65 mm outside diameter maintains the same routing compensation as the original Gecko setup using a 1/4-inch cutter and a 16 mm guide bushing.
The compensation is calculated as follows:
Original cutter: 6.35 mm
Original guide: 16.00 mm
Original radial offset: 4.825 mm
New cutter: 12.00 mm
Required new guide: 21.65 mm
This allows the original Gecko templates to produce the same final cavity dimensions with the larger 12 mm cutter.
Routing Performance
The deep insert cavity produced by this system is approximately 13.35 mm wide.
Because the cutter is 12 mm wide, it removes almost the entire insert width in one longitudinal movement.
Move the guide gently against both sides of the template to remove the remaining approximately 0.675 mm on each side.
The 12 mm cutter removes significantly more material per movement than a 6 mm cutter and has enough cutting length for the deeper side fin boxes.
This is still a two-stage routing system:
Deep insert cavity
Shallow flange cavity
The two Gecko templates are still required.
2. Timmy 3D Tool – Depth Setting and Jig Levelling
The Timmy 3D Tool has two separate functions.
Function 1: Levelling the Gecko Jig
The 8.00 mm reference is used to check that the Gecko jig is correctly positioned and level above the surfboard surface.
Place the 8 mm levelling shoulder against the jig.
When the jig is correctly levelled, the lower edge of the tool should just touch or lightly graze the surfboard foam.
If one side does not touch the foam, use EVA shims under the jig until it is level and correctly supported.
The purpose of this reference is to maintain the correct 8 mm distance between the upper routing surface of the jig and the surfboard surface.
Function 2: Setting the Router-Cutter Depth
The other three references are used to set the cutter projection for each routing operation:
FLANGE — 9.60 mm: shallow flange cavity
CENTER — 20.70 mm: 1/2-inch center fin box
SIDE — 27.05 mm: 3/4-inch side fin boxes
The cutter projection is measured from the flat underside of the router base—the surface that slides on top of the Gecko jig—to the tip of the cutter.
The top or bottom of the guide bushing is not the depth reference.
The guide bushing controls only the lateral movement of the router.
Nominal Depth Calculations
Flange
Gecko jig thickness: 8.00 mm
Nominal flange depth: approximately 1.60 mm
Cutter projection: 9.60 mm
Center Fin Box
Gecko jig thickness: 8.00 mm
Nominal center box depth: 12.70 mm
Cutter projection: 20.70 mm
Side Fin Boxes
Gecko jig thickness: 8.00 mm
Nominal side box depth: 19.05 mm
Cutter projection: 27.05 mm
Always measure the actual fin boxes before routing because manufacturing dimensions may vary.
Futures Alignment Target
This alignment target is designed to fit inside the Gecko Futures two-pass routing jig. It helps position the jig accurately before routing and is removed before using the router.
The target includes:
A full-length center sight line for aligning the box with the marked fin line.
A rear shaper-dot cross positioned 14.5 mm forward of the routed flange’s rear edge.
When the rear cross is placed over the shaper dot, the fin’s trailing edge should align with the selected distance from the tail.
A second cross positioned exactly 114.3 mm (4.5 in) forward for checking toe and longitudinal alignment.
Two outside reference lines positioned ±3.175 mm (±1/8 in) from the centerline.
Pass-through sight openings at the center and both 1/8-inch reference positions, allowing the pencil line underneath the target to remain visible.
Engraved outlines representing the expected insert and flange routing areas.
A nose-side finger notch for removing the target without moving the jig.
A solid 5 mm thickness to keep the target flat and rigid.
How to use
Mark the desired fin trailing-edge position on the surfboard.
Draw the fin alignment or toe line through that point.
Place the Gecko jig over the marked area.
Insert the alignment target into the jig.
Position the rear cross directly over the shaper dot.
Align the center sight line with the marked fin line.
If using a traditional 1/8-inch offset layout, use the appropriate outside sight line instead.
Secure the jig firmly.
Remove the alignment target before routing.
The 14.5 mm rear-cross position was checked using a physical Futures-compatible box and fin. Because aftermarket boxes and fins may vary slightly, users who require absolute precision should verify the trailing-edge offset with their own components before routing a finished board.
This is an independently designed accessory intended to complement the Gecko Futures jig. It is not an official Futures Fins or Gecko Surfboards product.
Compatibility
This kit is designed to complement:
Gecko Surfboards 8 mm two-pass Futures router jigs
The Makita router-base geometry used with the original Gecko jig files
Bosch Ø12 × L31.5 × S8 straight router cutter
Accurately equivalent 12 mm cutters with an 8 mm shank and sufficient cutting length
Check the mounting-hole pattern against your router before printing.
Makita router models and regional versions may have different mounting patterns.
The original Gecko router jigs can be downloaded separately from:
https://www.geckosurfboards.com/surfboard-building-router-jigs/
Recommended Print Settings
Makita Router Base
Material: PETG, ABS or ASA
Scale: 100%
Perimeters: minimum 5
Infill: minimum 40%
Print with good dimensional calibration
Check that the guide bushing is round
Check the outside and inside diameters with digital calipers
Timmy 3D Tool
Material: PETG recommended
Scale: 100%
Perimeters: minimum 4
Print flat
No supports required
Check all depth references with digital calipers
Alignment Target
Material: PETG recommended
Scale: 100%
Perimeters: minimum 4
Infill: 20–40%
Print flat
Transparent filament is optional because the alignment slots are open
Essential Checks Before Routing
Before using the system on a surfboard:
Measure the actual cutter diameter.
Confirm that the cutter rotates freely without touching the printed guide.
Confirm that the 21.65 mm guide moves freely inside both Gecko templates.
Confirm that the guide has minimal unwanted sideways play.
Measure the actual center and side fin-box depths.
Verify the Timmy 3D Tool dimensions with digital calipers.
Make a complete test cut in scrap foam or another inexpensive material.
Test-fit the real fin box in the test cavity.
Check the flange depth and fit.
Only use the system on a surfboard after completing a successful test.
Printer calibration, filament shrinkage, cutter dimensions and fin-box dimensions can vary.
Never assume that printed or manufactured parts are perfectly nominal.
Use controlled and progressive routing movements. Do not force the cutter or router against the printed guide.
Concept, functional design, measurements and testing direction:
Nada
