1 / 2
Kemono Fursuit Head Upgrade Parts – Fans, LEDs & Magnetic Eyes — image 1
1 / 2

Kemono Fursuit Head Upgrade Parts – Fans, LEDs & Magnetic Eyes

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Upgrade parts for a Kemono fursuit head: cooling fans, WS2812B LEDs, magnetic eye mesh and eyelids.

Rating
0 / 5
Likes
1
Downloads
2
Makes
0
Views
50
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

Kemono Fursuit Head Upgrade Parts

This is a collection of custom parts I designed while building my Kemono-style fursuit head.
They are intended to be used with the Kemono Fursuit Headbase by furns, which is linked as the original model for this remix.

The original headbase geometry is not modified. These files are additional components designed to improve cooling, lighting, eye assembly and general serviceability of the head.

Scale disclaimer:
These parts were designed to fit the original headbase scaled to 124.84%, resulting in an overall width of approximately 300 mm (30 cm). If you print the original headbase at a different scale, these parts will need to be scaled accordingly.

Included parts

Mouth / LED assembly

  • Custom upper mouth insert designed to fit a 4020 blower fan.

  • Integrated ventilation grille.

  • Mounting locations for two WS2812B LED modules.

  • Separate LED lens frames that can hold thin translucent or diffusing plastic.

Cooling system

  • Additional fan holders designed to be installed near the ears for increased airflow inside the head.

  • Separate fan grille.

  • Dust-filter stencil/frame for making a simple fan filter if desired.

Eyes

  • Slim eye socket/eyeblank version with space for WS2812B LED modules.

  • Alternative eye part without the LED mounting features.

  • Removable eye-mesh frame with small magnet pockets.

  • Magnetic eyelid frame that can be installed around the eye socket, allowing different eyelids to be attached or swapped.

Magnetic eye system

The eye-mesh frame was designed so the printed mesh can be removed instead of being permanently glued into the head. This makes it easier to:

  • clean the eye mesh;

  • replace damaged mesh;

  • experiment with different eye designs;

  • swap between multiple eye meshes.

Small neodymium magnets are installed in the corresponding holes in the frame.

The eyelid system uses the same idea, allowing removable or interchangeable eyelids.

LED system

The parts were designed around individual WS2812B addressable RGB LED modules cut from a standard strip.

My complete setup uses approximately 10 LEDs, although the exact number depends on which parts you decide to install.

For the LED diffusers I reused thin plastic layers from an old LCD backlight, but approximately 0.5 mm translucent plastic sheet or another suitable diffuser should also work.

Hardware / materials

Depending on which parts you use, you may need:

  1. 5 × 2 mm neodymium magnets

  2. CA glue (superglue) or epoxy

  3. Thin translucent/diffusing plastic sheet, approximately 0.5–0.8 mm

  4. M3 × 25 mm screws – 3 pcs

  5. M3/M4 × 20 mm screws – approximately 8 pcs

  6. Matching nuts

  7. WS2812B addressable RGB LED strip/modules

  8. 4020 blower fan

  9. Additional small fans if using the ear cooling mounts

Printing

Most of the parts are relatively small and were designed to be easy to print. Orientation may depend on your printer and material, so check the preview before slicing.

PLA should work for most of the components, although PETG may be preferable for parts exposed to higher temperatures or mechanical stress.

Assembly notes

Before permanently gluing anything to the headbase, I strongly recommend test-fitting every component.

Fursuit heads and prints can vary slightly depending on printer calibration, material shrinkage and assembly, so minor sanding or adjustment may occasionally be required.

When installing magnets, check their polarity before gluing them in place. This is especially important for the removable eye mesh and eyelid system.

Original model

These components were designed for the Kemono Fursuit Headbase by furns.
Full credit for the original headbase goes to the original creator.

If you build a head using these parts, I’d love to see the result!

Tags