HelloRadioSky V12 – Skyzone M5 FPV Monitor Mount (lanyard hook, no mods)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Clip-on mount that holds a Skyzone M5 FPV monitor on top of the HelloRadioSky V12. Locks to the radio's lanyard hook.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 4
- Makes
- 0
- Views
- 35
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- RC & Robotics
- License
- Creative Commons — Attribution — Noncommercial
A one-piece mount that puts a Skyzone M5 FPV monitor on top of a HelloRadioSky V12, with the M5 screen facing you, so you can see the monitor and the radio's own screen at the same time.
It doesn't modify the radio at all. It hooks over the top edge, rests on the screen bezel, and is locked to the radio's lanyard hook with a single M3 screw. The M5 is held by a normal 1/4" tripod thumbscrew.
FEATURES
• No mods: uses the radio's lanyard hook and a single M3 screw.
• Whole radio screen visible: the frame's two rails sit on the dead border either side of the picture.
• Nothing blocked: DSC, USB-C, SMA and the fan vents on top stay free, and SYS / MDL aren't touched.
• Smooth, filleted one-piece design. It follows the radio's contours and was built around a 3D scan of the V12 plus caliper measurements.
• 3 lean angles for the M5: 10°, 20° or 30°.
• Optional Voron heat-set insert for the M3, if you take it on and off a lot.
• Optional lanyard loop, so you can still hang the radio from your neck strap.
WHICH FILE?
File name: hoop_mount_tilt + angle + variant
• hoop_mount_tilt10 / 20 / 30 – self-tapping M3, no loop
• hoop_mount_tilt10 / 20 / 30_insert – Voron M3 insert, no loop
• hoop_mount_tilt10 / 20 / 30_loop – self-tapping M3, with lanyard loop
• hoop_mount_tilt10 / 20 / 30_insert_loop – Voron M3 insert, with lanyard loop
• 10 / 20 / 30 is how far the M5 leans back. 20° is a good middle.
• fit_test files are a 12 mm slice through the middle of the matching variant: the lanyard fork, the top band and the M5 lip. They take about 20–30 minutes; print one first and check the fit on your radio and the screw.
HARDWARE
• 1x M3x18 socket head screw
• 1x 1/4"-20 thumbscrew, max 1/2" thread, small knob (about 12 mm). Bigger knobs can touch the band on the 20° / 30° versions. The M5's tripod insert needs to take about 7 mm of thread.
• Insert versions only: 1x Voron-style M3x5x4 heat-set insert (OD 5 mm, length 4 mm), in a 4.4 mm hole.
PRINTING
• PETG or ASA. PLA works, but it can creep in a hot car.
• Lay it on its side on one of the flat outer faces. The fork, the bend over the top edge and the M5 lip are then all in-plane with the layers, which makes them strongest.
• 0.2 mm layers, 4 walls, 40% gyroid infill, tree supports, 5 mm brim.
• About 25 g. Size 67 x 97 x 28 mm (37 mm with the loop).
ASSEMBLY
1. Self-tap versions: run the M3x18 into the fork once from below to cut the thread, then take it out.
Insert versions: press the M3x5x4 insert into the hole on top of the fork with a soldering iron, flush.
2. Push the mount onto the radio from the front. The fork slides over the lanyard-hook plate, the rails land on the screen bezel, and the band goes over the top edge.
3. Put the M3x18 in from below the fork, through the hook's hole, and tighten with a 2.5 mm hex key. Snug only; it works as a pin.
4. Stand the M5 on the lip with its screen facing you; its bottom bezel rests on the ledge. Tighten the thumbscrew from behind.
LANYARD LOOP
The loop sits on the front of the fork, where the radio's original hook was. The bar is 6.5 x 4 mm and the opening is 7 x 5 mm; the clip goes through sideways. The loop only adds material to the fork. When the radio hangs from it, the pull goes straight into the radio's own hook plate.
NOTES
• Fits the HelloRadioSky V12. The V12 MAX / CNC MAX use the same shell and should fit, but that's not checked.
• Made for the Skyzone M5 (135 x 88 x 16 mm). Any monitor with a 1/4" thread on its bottom edge and about 16 mm thickness should sit on the lip. The thumbscrew slot allows ±2 mm for where the thread sits.