Glow Grid 16x16 LED panel case (frame, grid, diffuser cover, ESP32-C3 holder, desk cradle)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Case for a 16x16 WS2812B LED matrix: frame, cell grid, diffuser cover, ESP32-C3 holder and desk cradle
- Rating
- 0 / 5
- Likes
- 2
- Downloads
- 0
- Makes
- 0
- Views
- 21
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Electronics
- License
- Creative Commons — Attribution
Pixel art on an LED matrix looks harsh with bare LEDs. This case adds a black grid to the panel so each LED gets its own square, plus a thin white cover over the grid that diffuses each LED into a soft pixel. A frame holds the stack, a small tray holds an ESP32-C3 board inside the back, and a cradle tips the whole thing back 12 degrees on a desk.
It is the enclosure for the open-source Glow Grid project: a browser pixel editor plus a player for this panel. The ESP32-C3 build is self-contained: the board stores about 100 sprites, serves its own editor over your home Wi-Fi, and shows a one-time 8-digit password on the panel when you set up Wi-Fi. A Raspberry Pi 5 can also drive the panel from outside the case.
Code, editor, and example sprites (MIT): https://github.com/dwooods/glow-grid
Editor in your browser: https://dwooods.github.io/glow-grid/
Status
I printed and fitted everything in this package: frame v8, grid, cover, ESP32-C3 holder and cap, and cradle v15. The finished panel runs the Glow Grid firmware from the C3.
Files
File | What it is | Print orientation |
|---|---|---|
glow-grid_frame_v8 | 166 x 166 x 35.6 mm, open front, four spring fingers, 3 mm lip, 12.3 mm back-plate holes for a DC jack and two buttons, brackets for the C3 holder, USB-C slot | Back plate down |
glow-grid_grid_16x16_v2 | 161 x 161 x 8 mm, 10 mm pitch, 1 mm walls, no floor | Flat |
glow-grid_cover_0.6mm_v2 | 168.7 x 168.7 x 3.6 mm, 0.6 mm diffuser plate with a 3 mm lip | Plate down |
glow-grid_c3_holder_and_cap_v3 | Pins-up tray for an ESP32-C3 SuperMini and the cap that slides on and stops the board from lifting | Flat; cap plate face down |
glow-grid_desk_cradle_v15 and glow-grid_desk_cradle_v15_plain | 12-degree cradle with two back posts and a low front hook. One has raised "PIXEL ART" lettering on the bar; one is plain | Feet down |
What you need (not printed)
16x16 WS2812B flexible LED matrix, 256 pixels, 10 mm pitch (I used a "DC5V WS2812 Digital Flexible RGB Matrix Screen Module Light, 16x16"). Measure yours: the frame pocket is 162 mm square.
5 V supply rated for addressable LEDs, 6 A, 5.5 x 2.5 mm barrel plug, center positive, with a UL or ETL mark.
Panel-mount DC jack for a 12 mm hole.
ESP32-C3 SuperMini (24 x 18 mm, USB-C, u.FL) and its stick-on Wi-Fi antenna.
Two panel-mount push buttons for 12.3 mm holes (check body length; frame v8 has 3 mm of extra room).
1N5819 Schottky diode, 18 AWG wire for panel power, 22 AWG for the C3.
For the cradle: 4 x M3 x 8 mm screws (not M3 x 10) and about 1 mm double-sided tape.
Assembly
Order, back to front: frame back plate, C3 holder with the board and wiring, spring fingers, LED panel, grid, white cover.
Flash the C3 on the bench first. Its BOOT and RST buttons face the panel and can't be reached once the case is closed. Flashing steps are in
c3/README.mdin the repo.Solder wires to the C3's pin tips. Drop the board into the holder, components down and pins up, with the antenna plugged in, then slide the cap on from the far end.
Glue the holder into the three brackets on the back of the frame.
Fit the DC jack and two push buttons. The 12.3 mm holes are slightly loose for a 10.8 mm jack body, but the nut tightened from inside holds it fine. Stick the antenna in its recess and route the cable away from the power wires.
Wire as in the wiring diagram image (summary below).
Lay the panel in the frame (its wire tail leaves through the gap in the left lip), then the grid, so each LED sits in its own square.
Press the cover on. Its lip fits over the outside of the frame with 0.15 mm clearance, and four small bumps hold it by friction. The spring fingers press the stack forward against the cover.
Cradle: tape in the post recesses, rest the frame on the shoulder, and drive the M3 x 8 screws from the back of the posts into the frame's back plate. They cut their own threads, so the frame needs no pre-made holes (a 2.5 mm pilot hole is advised).
Wiring (summary)
Supply plug to the panel-mount jack. Jack +5V and GND go to the panel's 5V and GND leads on heavy wire (18 AWG or thicker, short). All LED current runs only on those two wires.
The C3 takes a thin branch from the same jack through the Schottky diode (bar toward the C3). Never run the panel's current through the C3's 5V pin. Use USB only for flashing, not power.
C3 GPIO6 to the panel's DIN. If your panel flickers, add a 74AHCT125 level shifter.
Next button on GPIO5, on/off button on GPIO7, each to GND. Hold the on/off button for 5 seconds to open Wi-Fi setup.
Keep brightness around 0.3 on a 6 A supply: a fully white frame at 0.3 draws about 4.7 A.
What I did, and what to upgrade: this is a hobby build. Some joints on my unit, including parts of the power path, use Dupont-style jumper connectors for convenience. Those pins are typically good for only 1 to 3 A, well under the panel's peak draw, which is why I run the panel at brightness 0.3 and why you should not copy this part. For a unit you leave running, make the 5V and GND runs from the jack to the panel with soldered joints and heat shrink, or screw terminals or lever connectors rated 10 A or more, and keep Dupont connectors for the C3's thin signal wires and buttons only. My panel's connector is held with hot glue; use a cable tie or clip for strain relief instead.
Print settings
ELEGOO Neptune 4 Pro (Klipper, 0.4 mm nozzle), OrcaSlicer, generic PLA, no supports needed. Your slicer will probably warn that the frame has "floating regions" and suggest supports (the spring-finger tips, the USB slot top, and the lip underside). Ignore it: I printed the frame with no supports at all, in this orientation, and it came out fine. The same goes for the other parts.
Frame: 0.24 mm layers, 4 walls, 15% infill, back plate down, 4 mm brim, bed 55 C first layer then 60 C, fan 80%.
Grid: black, 2 walls, no infill, brim, fan 80%.
Cover: white, 0.20 mm layers, plate down, 3 solid bottom layers.
Holder and cap: 0.20 mm, 3 to 4 loops. Print these first (about 10 to 15 minutes) and check the slide before the frame.
Cradle: 0.24 mm, 3 loops, 15% infill.
My OrcaSlicer profile (copy it if you have a similar printer)
Printer: ELEGOO Neptune 4 Pro (Klipper, 0.4 mm nozzle), OrcaSlicer, generic PLA. Values below are from my exported profile; treat them as a starting point, not a guarantee on other printers.
Setting | Value |
|---|---|
Nozzle / bed | 215 C (225 C first layer); bed 55 C first layer, 60 C other layers |
Layer height | 0.24 mm for the frame and the 0.24 mm profile; 0.20 mm for the cover, holder, and cap |
Walls / shells | 4 wall loops; 5 bottom and 3 top layers |
Infill | Tri-hexagon pattern; 15% on frame and cradle, none on the grid |
Speeds | Inner walls and infill 250 mm/s; top surface 200; first-layer infill 150; travel 500; acceleration 10000 |
Max volumetric speed | 16 mm3/s |
Fan | 80% on every layer, including the first |
Brim | Outer brim, 4 mm, on the frame and grid |
Elephant foot compensation | 0.2 mm over 2 layers (stops the first layers bulging at the bed) |
Retraction | 0.4 mm at 60 mm/s; Z-hop spiral lift 0.4 mm on all parts, retract on layer change |
Supports | None |
Times from the slicer (estimates): frame about 2 h 40 min and 125 g, grid about 2 h 30 min and 45 g (most of the time is travel between cells), desk cradle about 1 h 39 min and 72 g, diffuser cover about 31 min and 27 g, C3 holder about 8 min and 3.6 g.
Not verified
The panel's true outer size and whether its back has components where the fingers press. Measure your panel.
The spring fingers are 2.0 mm PLA cantilevers (I thickened them in v8 because the longer v7 fingers were too soft); their force is not measured. PLA can creep; if the stack loosens, raise
FING_PRELOADin the script or use foam pads.The cover's friction fit may need the bumps resized for your printer.
The cradle's tape and self-tapping screws into PLA are untested over time. A screw through a 3 mm plate can split it, so test on a scrap.
C3 board dimensions are close but were not caliper-measured. SuperMini clones vary, so print the holder first.
Wi-Fi setup was tested from Windows 11 and an iPhone, not Android.
Edit or regenerate
The parts are generated by a Python script (enclosure/build.py in the repo). Sizes are at the top of the script. pip install numpy trimesh manifold3d shapely, then python3 build.py out.
Credits and license
Case design descends from three CC BY designs on Thingiverse: "16x16 RGB Matrix" by The_Wrench_DIY (https://www.thingiverse.com/thing:4127683), its remix by chummer (https://www.thingiverse.com/thing:4459985), and the one-part-frame remix by makeitworktech / Make It Work (https://www.thingiverse.com/thing:5737371; video: https://www.youtube.com/watch?v=WSex5f1qzH8). This version is a script-generated redesign (enclosure/build.py) with new dimensions for the 16x16 panel, a separate holder and cap, and a desk cradle. Licensed under CC BY 4.0. I used only the 10 mm pitch and 1 mm grid walls from the earlier designs; I didn't use any mesh from them.
The code, editor and example sprites are MIT. The example sprites are all original; I'd ask that remixes keep them that way if they are shared.
