Snap-fit case for 16S balance lead adapter PCB from NKON (16S, 80×60 mm, LUNA2000 → BMS)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Snap-fit case for 16S balance lead adapter PCB from NKON (16S, 80×60 mm). No screws, parametric OpenSCAD.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 0
- Makes
- 0
- Views
- 8
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Electronics
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
If you bought the LUNA2000-5-E0 modules from NKON and are converting them to a JK inverter BMS, this is the case for the balance adapter PCB that comes with them (80 × 60 mm, 16S pads, 2.54/2 mm headers, JST-XH and 2×9 side-entry connectors).
The adapter PCB has no mounting holes, and after soldering the balance harness it is usually covered in hot glue. This case is designed around that reality:
Nothing touches the board edges. The lid is a cap whose skirt fits outside a thin rim on the base, so no part of the lid reaches inside the base cavity. Hot glue right up to the board edge is fine.
Snap-fit, no screws. A ridge on the outside of the base rim snaps into a matching groove inside the lid skirt. Both faces are printed at 30°/45° so they come out clean without supports.
Board held by four corner ledges underneath and four small 3 mm posts from the lid.
Cable slots: a 70 mm wide slot for the balance harness on the pad side, and a stepped opening on the connector side shaped for the two side-entry plugs (JST-XH with latch, 2×9 header) that stay plugged in.
Engraved label on the lid (editable or removable in the OpenSCAD source).
Fits a PCB of 80 × 60 × 1.6 mm with up to 5 mm of components/glue underneath and 10.5 mm above. Outer size 88.5 × 68.5 × 20.3 mm. About 40 g of PETG for both parts.
Fully parametric. The .scad source is included. Board size, clearances, heights, slot positions, snap strength, wall thickness and the label text are all variables at the top of the file, so it is easy to adapt to a different board.
Files
pcb_case_base.stl— base (tray)pcb_case_lid.stl— lid, already oriented for printing (label side down)pcb_case.stl— both parts side by side in one filepcb_case.scad— OpenSCAD source
Print settings
Material: PETG (tested on Bambu Lab P2S, textured PEI plate)
Layer height: 0.2 mm (keep 0.2 — the snap ridge is only ~1.3 mm tall)
Walls: 3, infill irrelevant (the model is all walls)
Supports: none. Both parts print flat side down as exported.
Brim: not needed on textured PEI
Assembly
Drop the board onto the four corner ledges with the balance pads toward the wide slot. Route the harness through the wide slot and the plugs through the stepped opening (the taller side is for the JST-XH plug). Press the lid on at the middle of the short sides until it clicks.
Tuning the snap
If the lid is too tight or too loose, change snap_d in the .scad (0.8 default): 0.7 for a softer snap, 0.9 for a stronger one. lip_clr (0.15) is the skirt-to-rim clearance.
Tags
pcb case, enclosure, snap fit, bms, jk bms, luna2000, nkon, huawei, battery, balance leads, openscad, parametric, petg
Category
Hobby & Makers → Electronics → Enclosures
The design is original; the LUNA2000, JK-BMS and NKON names are used only to describe compatibility and where the board comes from.
