1 / 4
Lian Li PC-8FI Internal PiKVM v2 Mounting Tray (RPi 4, HDMI-CSI, ATX Optocouplers) — image 1
1 / 4

Lian Li PC-8FI Internal PiKVM v2 Mounting Tray (RPi 4, HDMI-CSI, ATX Optocouplers)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Internal mounting tray for DIY PiKVM v2 (RPi 4, HDMI-CSI bridge, USB splitter & ATX optocouplers) inside a PC chassis.

Rating
0 / 5
Likes
0
Downloads
0
Makes
0
Views
6
Reviews
0

Updated at source:

Model information

Category
Electronics
License
Creative Commons — Attribution — NoDerivatives

Overview

This is a custom-designed internal mounting tray (modeled in Shapr3D) to install a complete DIY PiKVM v2 hardware stack directly inside a PC chassis.

Originally built for the brushed aluminum Lian Li PC-8FI mid-tower case, it mounts cleanly onto any flat interior chassis surface or drive bay frame. Keeping the PiKVM entirely internal eliminates external dongle clutter, protects all ribbon cables, and provides continuous, out-of-band IPMI remote management over the network.


Components & Hardware (Bill of Materials)

  • Compute Node: Raspberry Pi 4 Model B (2GB, 4GB, or 8GB).

  • Storage / Boot: 32GB USB 3.0 flash drive (using Pi 4 native USB boot to prevent MicroSD flash wear).

  • HDMI Capture Bridge: Waveshare HDMI-to-CSI-2 adapter board (HC100F with Toshiba TC358743 chipset).

  • Video Ribbon Cable: Standard 15-pin FPC CSI ribbon cable (routes directly from the Waveshare bridge to the Pi 4 camera port with zero twisting).

  • USB Power/Data Splitter: GODIYMODULES Type-C Power Splitter (isolates 5V power to prevent backfeeding between the host motherboard and the Pi while passing USB OTG keyboard/mouse data).

  • Internal Motherboard USB Adapter: CERRXIAN PH722 9-pin motherboard USB 2.0 header to USB-C adapter (connects to the motherboard's internal JUSB1 header).

  • ATX Motherboard Isolation: 4× 1-channel PC817 optocoupler boards (provides dry-contact switching and isolated status monitoring).

  • Fasteners:

    • 4× M2.5 × 6mm screws for Raspberry Pi 4

    • 4× M2 × 4mm screws for Waveshare HDMI-CSI bridge

    • 3M VHB heavy-duty double-sided tape (or chassis M3 screws) to mount the plate inside the case


3D Printing Recommendations

  • Recommended Filament: PETG, ABS, or ASA (recommended to withstand elevated ambient temperatures inside a running PC chassis near drives and VRMs. Standard PLA works if your case has good intake airflow).

  • Layer Height: 0.20 mm

  • Perimeters / Wall Loops: 3 or 4 walls (ensures solid threading for mounting screws)

  • Infill: 20% to 25% (Gyroid or Grid)

  • Supports: None required (the plate is designed completely flat with zero overhangs)

  • Brim: None needed


ATX Wiring Guide (Motherboard Front Panel JFP1 Header)

Connect the 4 optocoupler channels as follows:

  • Power Button Actuation:

    • Motherboard JFP1 Pins 6 & 8 → Optocoupler 1 Output (OUT & GND, leave VCC disconnected)

    • Raspberry Pi GPIO 23 (Pin 16) →Optocoupler 1 Input (+), Pi Ground → Input (-)

  • Reset Button Actuation:

    • Motherboard JFP1 Pins 5 & 7 →Optocoupler 2 Output (OUT & GND, leave VCC disconnected)

    • Raspberry Pi GPIO 27 (Pin 13) →Optocoupler 2 Input (+), Pi Ground →input (-)

  • Power LED State Detection:

    • Motherboard JFP1 Pins 2 & 4 →Optocoupler 3 Input (+ to Pin 2, - to Pin 4)

    • Raspberry Pi GPIO 24 (Pin 18) →Optocoupler 3 OUT

    • Raspberry Pi 3.3V (Pin 1) → Optocoupler 3 VCC

    • Raspberry Pi Ground (Pin 9) → Optocoupler 3 GND

  • HDD Activity LED Detection:

    • Motherboard JFP1 Pins 1 & 3 → Optocoupler 4 Input (+ to Pin 1, - to Pin 3)

    • Raspberry Pi GPIO 22 (Pin 15) → Optocoupler 4 OUT

    • Raspberry Pi 3.3V (Pin 1) →Optocoupler 4 VCC

    • Raspberry Pi Ground (Pin 9) →Optocoupler 4 GND


PiKVM Software Tip (Inverted LED Logic)

Because 1-channel PC817 modules use an active-low pull-up circuit (the output is pulled to Ground when the motherboard LED turns on), the sensor signal is inverted.

To make the PiKVM web interface display the Power and HDD indicators correctly, add these lines into /etc/kvmd/override.yaml on your PiKVM:

kvmd:
atx:
power_led_inverted: true

Then restart the daemon: systemctl restart kvmd

Tags