1 / 8
Lian Li O11D EVO RGB Bottom Fan Floor Tray – 3 × 140 mm Fans — image 1
1 / 8

Lian Li O11D EVO RGB Bottom Fan Floor Tray – 3 × 140 mm Fans

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Drop-in floor cover for three 140 mm bottom fans. Fills the space around them and sits flush with the fan tops.

Rating
0 / 5
Likes
0
Downloads
0
Makes
0
Views
6
Reviews
0

Updated at source:

Model information

Category
Computers
License
Creative Commons — Attribution — Noncommercial — Share Alike

Fills the bare floor around three 140 mm bottom fans in the Lian Li O11 Dynamic EVO RGB and sits flush with the top of 25 mm fans, for a clean, finished look through the glass. No screws, glue or tools.

Three pieces

  1. Front Tray: L-shaped. Covers the floor between the front glass and the first fan, plus the space in front of the motherboard tray. Notched around the aluminium pillar in the glass corner.

  2. Side Tray, FRONT piece: runs along the side glass beside the fans. Its size matches your tray.

  3. Side Tray, REAR piece: locks on with a dovetail and runs to the rear panel. The same for everyone.

Built from Lian Li's CAD model

Every file was checked against the official O11D EVO RGB model. Nothing touches the glass, trim, pillar, bottom fans or side fans. Every support pad and rib lands on a flat spot, and the rim stays above the glass trim so the RGB-lit edge stays uncovered. Three 140 mm fans reach 20 mm further toward the motherboard than 120s, so this tray's arm is 20 mm narrower than the 120 mm version.

Pick your size

Measure from the inside face of the front glass straight back to the front edge of the first bottom fan's frame (the hard frame, not a rubber corner).

Sizes (mm): 25, 27, 29, 31

Three 140 mm fans fill the bracket, so the gap is always about 25–32 mm. Measure anyway; it depends on where your bracket sits. Between two sizes? Use the smaller one.

Then print three files. For a 29 mm gap, for example:

  • Front Tray_140_gap29mm.stl (Front Tray folder)

  • Side Tray_140_FRONT_gap29mm.stl (Side Tray folder)

  • Side Tray_140_REAR.stl (Side Tray folder, the same for every size)

On the 25, 27 and 29 mm trays the front edge stops at the corner pillar, because the space beside the pillar is too narrow to fill. That's expected.

Fans spaced apart, or a size that isn't listed? Open the included .scad files in OpenSCAD (free), keep fan_size = 140, type in your exact measurement, side fan thickness (0 = no side fans) and bottom fan thickness, then export the STL.

What it assumes

  • Three 140 mm fans on the stock bottom bracket, sitting on its plate.

  • 25 mm thick bottom fans. Use the .scad file for 28 mm fans.

  • Side intake fans up to 28 mm thick. The tray stops 1.5 mm short of them.

  • The standard (non-reversed) case layout.

Print settings

Setting

Value

Material

PETG or PLA (PETG if the PC sits somewhere warm)

Orientation

As exported, top face down

Supports

None

Layer height

0.2 mm

Walls

3

Infill

15–20 %

Size

Tray 188–212 × 180 mm, strip pieces up to 224 × 26 mm

Bed

250 mm or larger, or a 220 mm bed with the strips placed diagonally

Plastic

About 85 g per set in PETG

Install (about 5 minutes)

  1. Shut down, switch the PSU off and unplug the power cord.

  2. Take off the side glass (and the front glass if that's easier).

  3. Route the bottom fans' cables first.

  4. Lower the Front Tray into the front corner, around the pillar.

  5. Set the REAR strip piece along the side glass, against the rear panel.

  6. Drop the FRONT strip piece in from above so its dovetail lands in the rear piece. If it's tight, sand the tab lightly.

  7. Refit the glass and plug back in.

Images are renders on Lian Li's CAD model; some show both fan sizes. Not affiliated with Lian Li.

Tags