1 / 10
Multi-Modular-Development-Board-Enclosure (MMDBE) — image 1
1 / 10

Multi-Modular-Development-Board-Enclosure (MMDBE)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Modular Enclosure with USB-PSU and FAN for Development Boards or SBCs like Raspberrys or CoralBoard SL. Optional LEDs

Rating
0 / 5
Likes
1
Downloads
0
Makes
0
Views
20
Reviews
0

Updated at source:

Model information

Category
Computers
License
Creative Commons — Attribution — Noncommercial

Hey Folks,

let me introduce the MMDBE (Multi-Modular-Dev-Board-Enclosure)... Yeah, I know but I couldn’t find a better name for this. If you have something better, write it in the comments pleeeeeeeease....

Currently, I have uploaded two variants of the case, and one additional variant is in development.

  1. Case without LEDs – Optional internal LED lighting that shines through the fan and creates a glow underneath the case. Printable on any printer, as long as the case fits on the print bed.

  2. Case with LEDs at the front – You will need a multi-material printer for this version.

The third variant, which is currently in development, is intended to be printed on a single-material printer and adds LEDs to the front, integrated into the angled sides. It will take me a few more weeks to finish the model, so stay tuned if you want to print this version.

Please note: Some of you might have noticed that the black/white LED version of the case looks slightly different at the front feet compared to the white/green version. This is due to a design improvement.

I had some warping issues with the continuous front foot and the very small feet at the back of the case. So I changed the design in Version 2 (the white case without LEDs). It now has bigger feet at the back and two separate feet at the front instead of one large one.

So don't be surprised if your printed case looks a little different from the black one. I didn't want to print the whole thing again because it generally works fine for me and to be honest it needs some more filament to get printed, but I still wanted to improve the design for you.

TL;DR

Case for 5 development boards (like Raspberry Pi or CoralBoard SL) with a 120mm fan, integrated power supply and optional LED hardware status indicator. Modular, very stylish, unique, super useful, blah blah blah....

You should read the following chapters (in order of appearance):

Features (optional)
Print Settings
Case Assembly
Shopping List

Have fun :)

Introduction

This summer was very hot in Germany and my Raspberry Pis called it a day due to overheating from time to time.

The easy way to solve this would be to mount an ugly small fan on them but I found an unused 120mm fan lying around and furthermore I had packed the Raspberry Pis in separate cases which also turned out not to be that good at keeping them cool. They were located in the same place and each had its own power supply.

I decided to centralize things a little bit and created a case for all of my Raspberry Pis and added some additional space for more Dev-Boards with only one power supply for all of them.  

I know the summer is over now, but I didn’t had time before, and as the days are getting colder, I found some time to start this project and when I noticed this Printables CoralBoard SL contest, I decided to speed the development up a little bit to take part in this contest.  

Maybe it is not the best moment to make a Development Board Project especially for Raspberrys as they have become way too expensive and are also mostly unavailable but yeah I could also argue that this improves the lifetime of your existing Development Board with better cooling. However I hope you will have fun with this Project. 

Design process

The whole design of this project is more or less simply "form follows function".

The 120mm fan is the starting point here. I needed some additional space for an inner skeleton to mount it on, plus some more space for the outer walls.

Then there's the power supply, which shouldn't be in the fan's airflow as it would block the airflow through the DevBoards. So I decided to place it at the front of the case.

Now I have an unstylish functional Block which measures 140x180x170 (w/h/d) in which everything will fit.

The next question was, what would be a good orientation for the DevBoards and well that’s an easy one, vertically to not block the Airflow too much and I also wanted the Case to be modular, making it possible to use other DevBoards in the Case, not only Raspberry Pis. So I decided to design it as a Bay Layout and I have 130mm in width and a 6 port USB Power supply so I could divide the 130mm to 5 Bays and one USB Port for the Fan. As I have Bays with a kind of guide or rail system I mounted the DevBoards on Trays which then can be slid into the case.

Then there was another thing, how to identify a Raspberry which is built into a Case with possibly four other identical or similar-looking boards. Color Coding is the answer. Each DevBoard has its own tray, so why not print them in different colors to be able to identify a Raspberry. For example, the tray for the HA Raspberry is obviously light blue. 

120mm Fan + PSU + some space for cables to connect the PSU with the DevBoards (calculated with angled USB-A Cables as I wanted to save some height). Then this Box also needs a Top Cover with some cutouts in it for the Air exhaust. That brings the Case to a height of 192mm.

Next point, how to add some design to a block and I also need some holes at the bottom as an air intake. Well the Answer is Prusa Core One. Cutting off some unused corners, which also has the benefit that I can cut some more from the block at the bottom to have an air intake for the Fan. Furthermore it is a very printable design due to the angled surfaces. I don’t know who exactly made this design at Prusa, should be one of these guys, so all my respect, appeciation and credits to the Prusa Team: Michal Fanta, Matej Supik, Petr Memory Dragoun, Mikolas Zuza, Josef Prusa, Ondrej Prusa, Vit Fendrych

The thing is that the Core One has a door at the front which makes the space at the front useful but for my design there is no need for it so I have plenty of unused space. 

So I remembered that one of the biggest problems I had was that I didn’t notice that the Pis had gone offline due to heat. I only noticed when I needed them so in my case the lights in my corridor didn’t light up as they are connected with a motion detector and controlled by Home Assistant which is running on one of the Pis. So I decided to use the space for LED Indicators with a system monitoring. 10 Indicator Bars, two for each DevBoard which could be built into the case.  On each side of the transparent printed Bars are SK6812 LED Strips each with 10 LEDs (60 LEDs / Meter). As I have already written, each DevBoard has its own Tray Color which makes it possible to identify it also with the Status Indicator.
The left LED will indicate the Board and the right side will show its status. More regarding this in the Chapter for LEDs.

Well, that is the concept, let’s go to the Features.

Features

  • Chimney-Effect Case Layout

  • 5 Bays for Dev Boards (Like Raspberry)

  • 120mm fan

  • Supports 6 Port USB Power supply

  • Optional LED Hardware Status Indicator (See Details in own Chapter)

  • Modular Bay Tray Design - If you want, you can design your own tray if you can't find a tray for your dev-board. You can color code them to identify the Board.

  • Supports DevBoards with the following dimensions 125x75x24 (height can be more if you leave bays empty. for example, if you mount a HAT or other additional stuff)

  • Dimensions of the Case 140x192x170 (w/h/d)

Supported Hardware
  • 120mm Fan with a thickness of up to 25mm

  • USB Power Supply - I used the Anker 6 Port USB 60w Power supply. You can find a Link to the Product in the Linklist.

Currently supported Dev Boards
  • Raspberry Pi 3*/5

  • Untested Raspberry Pi 4 (the Ethernet Port and USB Block are switched in comparison to the other Raspberrys so I used the Design for the Raspberry 3*/5 and switched the cutouts but I don't have a 4 here so I can't test it.

  • Untested Coralboard SL (due to the Printables competition)

  • Supports DevBoards with the following dimensions 125x75x24 (height can be more if you leave bays empty. for example, if you mount a HAT or other additional stuff)

THE CASE

I have uploaded two versions of this Case, one with LED-Indicator Bars and one without.

MMDBE with LED Status Indicator

It is not possible to print this Model without a printer that can change the filament and looking at the print time I highly recommend a printer with a tool changer. You would additionally need to install SBOC. which is the software for monitoring the hardware (Running Linux/Debian or Homeassistant OS) and to control the LEDs. More on this in a separate Chapter.

MMDBE without LED Status Indicator

It should be printable on any printer.
There is also a picture of this version available. I printed it in two colors. For this, you have to add a break at layer 81 and then just change the filament manually. Then print the Top cover in the same color as the feet or do whatever you want to get this thing cool. I’m very curious about your makes. Please share them.

You could also install SBOC. to monitor your hardware (Running Linux/Debian or Homeassistant OS). The Software can also notify via email in case something is critical. 

I also modified one of the parts inside of the case to be able to mount LEDs. This should make a glow shining through the Fan to make a kind of underbody lighting. So it could light up when a critical situation appears.

Available Trays for the Bays
  • Tray for Raspberry Pi 3* / 5

  • Tray for Raspberry Pi 3*/ 5 reverse orientation - to have the connection ports of the PIs inside the case for a possible NAS configuration

  • Tray for Raspberry 4 (untested)

  • Tray for Raspberry Pi 4 reverse orientation - to have the connection ports of the PIs inside the case for a possible NAS configuration

  • Tray for Coral Board SL

  • Tray Utility Cable - for getting USB Cables from the outside to the inside of the Case

  • Tray Utility SONOFF Zigbee 3.0 USB Dongle Plus MG24 - with cutouts to get the USB extension cable from the Raspberry to the Stick 

  • Tray Blanko - Make your own Tray. This tray has no cutouts and screw/nut holes. You can do whatever you want with it. Would be cool if you shared your model on Printables as a remix then.

Print Settings

  • 0.4mm nozzle

  • 0.2mm layer height

  • 3 Perimeter/Walls this will improve the quality of the angled Surfaces.

  • Material: I used PLA to print this, I can’t imagine that the temperature in this case could be that high that something will melt. Furthermore, if something warps during printing, it could cause parts to no longer fit as I used some Rails to slide the Top Cover on the Case and also for the Top Holder for the Trays.

  • MMDBE without LED Status Indicator - should be printable with each printer

    • You could add a break in your slicer at Layer 81 to have an accent color at the feet. I used black in my example Version and you could repeat that printing the top cover in the same color as the feet.

  •  MMDBE with LED Status Indicator 

    • Use Transparent PLA for the LED Bars. 

    • Use Dark and solid PLA Filaments as Main Color for the Case like Black, Grey, Dark Red or Dark Blue. Otherwise the LED will shine through the Case. Could be intended but if not, I want to make you aware of it.

    • To define the LED Bars as transparent you have to cut the model in parts so you would have separate entries for the body itself and the Transparent Bars (Right click on the Model in the inspector then choose Split and then "to Parts"). Define the Transparent Bars with 100% infill and Aligned rectilinear infill type. I have aligned the case with the front to the door of the printer so I have set the angle of the aligned rectilinear infill to 0 degrees. Which means from left to right. This should help that the light of the LED will find its way in the right direction. Problem is, that I had to shorten the depth of the bars so they could fit in the front. That caused an unlucky angle for the light but well, it is fine for me. Furthermore, set the perimeter for the Transparent parts to 0 as you can see on the screenshot, as 0 is not possible it will print one outline so you could also choose 1 instead. Will not make a difference. I will also add an 3MF for this Model but Im not sure if this will work. Please double check it before print.

  • Parts to be printed

    • MMDBE Main Body Base (LED or without LED as described above)

    • MMDBE Top Cover - Print it Upside down so no supports are needed also 3 Perimeter/Walls

    • Skeleton Base Plate

    • Skeleton buttom Tray holder

    • Skeleton top Tray holder

    • Print the needed Trays

    • ONLY LED: LED Holder left - Use Brim to print it otherwise it could warp

    • ONLY LED: LED Holder right - Use Brim to print it otherwise it could warp

  • Supports: 

Main Body both versions - yes, you have to support the spaces between the feet and the bar above the DevBoard Bays. You can directly print the supports on the model. I had no problems to get rid of them.  Please see the Pictures for details

  • Top Cover - No, print it upside down

  • Skeleton_Base_Plate - Maybe.... I have supported the part on the screenshot. Should work without but well... why not

  • Skeleton_Buttom_TrayHolder - No

  • Skeleton_Top_TrayHolder - No

  • Trays for Raspberrys - No

  • Tray for CoralBoard SL - Yes - You have to Support the Cutouts

  • Tray Utility Board Cable - No

  • Tray Utility Board SONOFF Zigbee 3.0 USB Dongle Plus MG24 - Yes you have to Support the Inside of the USB Stick holder

Part

Filament in Gram (Slicer calculation, supports included, 
with suggested Print settings)

Mainbody LED

479g

Mainbody

450g

Top Cover

84,3g

Skeleton Parts

71,85g

Tray

Should have around 18g each

LED Holder

9g

Total - NON Led Version

Calculated with 5 trays 696,15g

Total - LED Version

Calculated with 5 trays 734,15g

Case assembly

  1. Optional: Install the M2 Heat-Set inserts into the base. See below.

  2. Place the 120mm fan into the base.

  3. Plug the angled 90-degree IEC320 C8 male to C7 female adapter into the USB power supply and connect the power cable that came with the power supply to the adapter. Then place the power supply into its holder at the front. Use the cutout at the lower middle of the back of the base to route the power cable outside.

  4. Place the skeleton base plate into the base.

  5. Place the fan controller onto its holder on the skeleton base plate. There is a hole for the fan controller's rotary knob. If the plastic handle is already attached to the knob, you'll need to remove it first. It's not glued or anything, so you can just gently pull it off.

  6. Connect the angled USB-A to straight USB-C 30cm cable to the power supply and the fan controller.

  7. Connect the fan cable to the fan controller. You should test the fan now before continuing.

  8. Place the skeleton bottom tray holder into the base.

  9. Slide the skeleton top tray holder into the base.

  10. Optional: Screw the skeleton top tray holder to the base.

  11. Only for the LED version: Prepare the LED holder. There isn't much space inside the LED slot, and the tolerance between the LED holder and the slot is nearly zero. It might help to sand the small back side of the LED holder a little so that it slides smoothly into the slot. Please make sure to wear respiratory protection while sanding.

  12. Only for the LED version: Attach the LEDs to the LED holder and slide them into the LED slot.

  13. Press the M2 nuts into the holes on the back of the board trays. Make sure they don't stick out, otherwise the trays might get stuck against the neighboring trays.

  14. Screw the boards onto the trays and slide them into the base.

  15. Only for the LED Version:
    Connect the LEDs to the used board as follows 
    Left LED Strip (10 × SK6812 RGBW)

    • Red (5V): Physical Pin 2

    • Green (DIN): Physical Pin 32 (GPIO12)

    • White (GND): Physical Pin 39

    Right LED Strip (10 × SK6812 RGBW)

    • Red (5V): Physical Pin 4

    • Green (DIN): Physical Pin 33 (GPIO13)

    • White (GND): Physical Pin 34




  16. Now you can connect the cables to the boards.

  17. Optional: If you want, you can screw each tray to the upper tray holder. Make sure the trays are fully inserted into the case before tightening the screws so that the holes in the trays line up with the holes in the upper tray holder. Don't tighten the screws too much. They're just there to secure the trays in place.

  18. As the final step, slide the top cover onto the base.

CoralBoard SL

To be honest, I started with the creation of the Case a few weeks before the Coral Board SL contest was announced but I thought the Board itself could fit perfectly in this Case. Not only due to the size of the board but more because of the way it could be used.

I read the documentation of the board and found some points the board could benefit and I also found a use-case for myself where I’m not sure if it would work or not but hey, it is a development board so room for experiments.

The contest rules say that it could be part of a Project.... Take a look at the picture, it is absolutely part of it (the red and the bright green Tray).

The CoralBoard SL setup and the benefits of my Case design.

I noticed that the board does not have any network connectivity by default.
You would need additional modules to add Wi-Fi or Ethernet to it. The contest says that the use should be only the board not the modules but anyway. The idea of the designer of the CoralBoard was that it will be connected to a host system from which it will get its power supply and ethernet over USB.
My setup would be to take one of the Raspberry Pis in the same case and use it as the host system.
In theory a Raspberry with installed Raspberry Pi OS/Debian should bring everything by default to identify the CoralBoard SL as a USB network adapter.

That also means a small cluster of Coral Boards SL would be possible if you just connect them with the Raspberry. Each of them would be identified separately and it would be possible to give them their own IP addresses.... 

The CoralBoard SL Use Case

I asked myself what could be a use case for a Coral Board SL and I had the following idea:
Coral Board supports the Models YOLOv8n / YOLOv11n, YOLO is a model for object detection and there is also a Project for Spaghetti/Print failure detection available. So I would give it access to the RTSP Stream of my Buddy-Cam to monitor my 3D print in case something goes wrong and can possibly notify me or stop the print..... well, that would depend on how accurate the detection is but yeah it is a usecase. I can’t find something like this built with this board but in theory it should work and as I said, it is a development board so let’s experiment with this thing.

What I have added to the Project in the context of the Coral Board SL, I created a dedicated tray for the CoralBoard SL with which you can slide the Board in one of the Bays.
I don’t know if it would benefit in the context of cooling but I think all Hardware will benefit from being kept a little bit cooler. 

I printed two of the boards to show the possible usage that it could benefit from the Case layout.
I broke one USB port when I tried to get the supports out of it (Sorry for that).

As they are also running Linux, it should be possible to install a SBOC. Agent on it in theory. If anyone can confirm that. Please let me know.

Well, as you can see these boards are Dead.... Status Indicator is red. I hope this will change, replacing one of these after this Contest ;)

Shopping List

You will find below a table with the additional parts I have used for the Case.


Transparency notice: I used Amazon affiliate links in this table and I will not hide that these are affiliate links. You can use them to support my work without any additional costs except your data or don't use them but it is important for me that you are aware that these are affiliate links. 
I wanted to make sure that you order parts which would fit and so you don’t have to buy them more than once (as I did several times in the context of USB Cable length).

If you want to support me more directly, you can buy me a coffee :) .... THANK YOU

In general, the best parts are parts you dont have to buy. Search in your old stuff if there is something you could recycle for this project.

You will find some Entrys which are marked as Optional. Some depend on your needs, like which Development Board you use, if it is powered with USB-C or Micro USB and the orientation of the Board in the Case and some are really Optional like screwing the upper Tray holder to the case or not. \

Part

Description

Amount

Amazon Affiliate Link

120mm FAN - Max Dimensions 120x25mm

Choose whatever you want. I used a Noctua which I’m currently not using

1

6 Port USB Power Supply - Max Dimensions 70x26x99mm

Anker - 6 Port USB 60w Power supply - A2123313

1

https://link.amazon/B03poD12N

Angled 90 Degree IEC320 C8 Male to C7 female Adapter

NOT the Vertical 90 degrees angled version

1

https://link.amazon/B02sp5rCw

Optional: Angled USB-A to Micro USB 15cm. ATTENTION:  In case you are installing your Raspberrys Reverse (Ports inside the Case) you would need 30cm Cable length

For Development Board Power Supply for example Raspberry Pi 3* Linked the Angled-Angled Cable. Cant find a Version with Angled USB-A and straight Micro USB. You should prefer this then.

Depending on Micro USB powered Boards

https://link.amazon/B0j8EyWgd

Optional: Angled USB-A to USB-C 15cm ATTENTION:  In case you are installing your Raspberrys Reverse (Ports inside the Case) you would need 30cm Cable length and you should choose the Angled/Angled Version

For Development Board Power Supply for example Raspberry Pi 5.

Depending on USB-C powered Boards

https://link.amazon/B09X45lTF

Angled USB-A to straight USB-C 30cm

For connecting the FAN Controller

1

https://link.amazon/B092t17Kb

FAN Speed Controller USB-C to 4PIN PWM (5V to 12V)

Needed to connect the Fan to the USB Power Supply

1

https://link.amazon/B02QhrQKO

Optional: USB A to USB A extender 30cm

Needed if you connect internal stuff to external ports of your boards. Like Connecting a Sonoff Zigbee Stick to a Raspberry

https://link.amazon/B010oNM6V

M2 Nuts for mounting Boards on Trays

Each tray has 4 mounting points and each will need a M2 nut

4 per Tray

Linked a Set of M* Screws and Nuts. You would need only one of this Sets ;) Nothing special here, you can take whatever you want. Just a suggestion: https://link.amazon/B02xyIxtw

M2x6 Screws for mounting Boards on Trays

Each Board Tray has 4 mounting points for each you will need 4 M2x6 screws
Optional: 2 M2x6 if you want to screw the upper tray holder to the Body

4 per Tray
Optional:
2 for the upper tray holder

See Above

Really Optional: M2x10 Screw

To screw the upper Tray holder to the Base. I use it without them but it is possible

2

See Above

Really Optional: M2 Heat-set Insert (For the ones never used this inserts you need a soldering iron for this)

To screw the upper Tray holder to the Base. I use it without them but it is possible

2

https://link.amazon/B090Jdg1e

Optional for LED: Addressable LED like SK6812 or WS2812b. Important: 60 LED/Meter

I used SK6812 LEDs but only because I had them. You can also use WS2812 which will not make a difference. Same driver

1 Stripe cut in two pieces each with 10 LED

https://link.amazon/B02xWJB3V

SBOC. - Local Development Board System Monitoring Solution

Transparency Notice: This is Vibecoded Software. If you feel uncomfortable with AI-Generated Software you dont have to use it. The case on its own will work without the LEDs and System Monitoring.
If you want to know more why this is AI-Generated and my opinion about this, there is a chapter in the GitHub repository in which I explain it. 

SBOC. is the piece of Software which monitors the Development Boards and controls the LEDs and can also notify you via email in case something critical happens. 

It has a Controller/Agent architecture, so you have to install the Controller Version (it is the same install file you have to choose during the install process) on one of the Development Boards and install the small Agent Version on the other Development Boards. It has been tested with Raspberry Pi OS, so in general it should work on any device running Debian, but I haven’t tested that yet.

For the Home Assistant OS there is another solution as it is not possible to install an Agent on it. You can add a HA Long-Lived Access Token to SBOC. and install the System Monitor integration on HA which creates sensors for the HA System Parts. You can then read these sensors in SBOC..

Features:

  • CPU Temperature

  • CPU Load

  • RAM Usage

  • HDD Usage

  • Network Traffic

  • Monitor System Services (you can choose which should be monitored)

  • Monitor Container Status (untested yet but should work)

  • Define LED colors and thresholds

  • Silent Mode: LEDs only light up if something is in a bad state for the specific device.

  • Night Mode: You can choose a Time Frame in which the LEDs are turned off.

  • Mail notifications.

Please see the Git Repository for more information 
https://github.com/M3ro-3D/SBOC

Further Improvements

Currently Im working on a 3rd Version wich uses the angeled left and right sides for LED Implementation which then can be printed on Single-Material Printers. The first results are promising but it needs some further improvements for which I would need some more time and as I wrote I wanted to participate in the CoralBoard SL contest. Please come back later if you are interested in this Version. 

In general, my own usecase is currently fully covered by the case so there is no need to improve it for myself.
One idea is to add another level on top of the case for more space if you want to use it as NAS for example but there is no need for my own usage to design something like this but lets see how many of you like this Project and possibly would have a need for a NAS Top.
Let me know this in the comments also if you have other needs or ideas.

If you have further Ideas and needs write it in the comments. If there would be something which is not a single User need, I would try to implement it.

Last Words

I have printed 3 Cases and had no big problems, so I’m very confident that this will work also on your side. The uploaded design is Version 2 with some minor improvements like the possibility to screw the upper tray holder to the case. I experienced the issue that if you remove a tray you could also slide out the upper tray holder. It is not a big deal and I marked it as optional as the solution is to use Heat-Set Inserts and screw the holder to the case and if you can live with it, there is no need to buy Heat-Set Inserts. You will not remove the trays daily. So no problem in general but I wanted to offer a solution for this problem.

I hope you will have fun with the Case and everything will work as it is intended.
Please show me your makes. I’m very curious to see your results.

☕ Powered by Coffee

Some projects run on electricity. Mine run on coffee. ☕

Coffee is my fuel, and quite a few cups have already gone into building MMDBE and SBOC.

If you enjoy this project and would like to keep the caffeine flowing, I'd be happy about a little contribution to my coffee fund.

https://buymeacoffee.com/m3ro

Tags