1 / 4
Yaesu FT-817 3x18650 battery holder - alternate fuse holder — image 1
1 / 4

Yaesu FT-817 3x18650 battery holder - alternate fuse holder

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

This is a minor change to the great battery holder posted by tandro. I updated it to Accommodate a different fuse…

Rating
0 / 5
Likes
14
Downloads
99
Makes
0
Views
881
Reviews
0

Updated at source:

Model information

Category
Electronics
License
Creative Commons — Attribution

This is a minor change to the great battery holder posted by tandro. I updated it to

  • Accommodate a different fuse holder
  • Deeper wire channels between the positive and negative battery terminals that get connected to allow for the additional wire

I have included a schematic of the wiring and a picture of the backside, unfortunately the short wire lengths make it difficult to make out the details in the photo.

Print Settings

Printer Brand:

Prusa

Printer:

i3 MK2S

Rafts:

No

Supports:

No

Resolution:

0.2mm

Infill:

20%

Notes:

Printed in PETG

Post-Printing

Parts

Fuse holder: https://www.amazon.com/gp/product/B074N1NMMX/ref=oh_aui_detailpage_o08_s02?ie=UTF8&psc=1

SPDT ON-Off Miniature Slide Switch https://www.amazon.com/gp/product/B007QAJST6/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1

Silver Metal Battery Spring Plate: https://www.amazon.com/gp/product/B00GN3PN46/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1

JST-GH (5pin, 1.25mm), male + female: https://www.ebay.com/itm/401300171811

JST-XH(Balance, 4pin, 2.5mm): https://www.amazon.com/gp/product/B073ZG87DG/ref=oh_aui_detailpage_o08_s01?ie=UTF8&psc=1

balance charger: https://www.amazon.com/gp/product/B004FGWY54/ref=oh_aui_detailpage_o08_s02?ie=UTF8&psc=1

charger connector: https://www.amazon.com/gp/product/B078QNS7YL/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1

Bend the terminal contacts of the fuse holder flush with the fuse housing before inserting

Pre-solder wires to the switch before inserting, I covered the contacts with heat shrink tubing just to keep it safe

Trim the tabs off of the battery contacts before inserting, otherwise they will extend below the case and cause a short circuit.

When soldering, make sure none of the solder extends beyond the base of the case, cover any questionable solder joints with electrical tape

When soldering the battery terminals, strip a little off the wire, push the wire far enough in so there is no exposed wire near the base. Solder the wire to the terminal from the top

WARNING

Usage of Li-ion batteries is at your own risk!

Use caution when working with Li-ion cells; they are very sensitive to charging characteristics and may explode or burn if mishandled.

You must have appropriate understanding of lithium ion batteries when charging, discharging, and assembly before use.

Please perform your due diligence and make sure that this battery is compatible with the item for which you intend to use.

Battery may explode or catch fire if mistreated.

I accept no responsibility or liability for any injury, damage, or defect, permanent or temporary that may be caused by the improper use of a LI-ION battery.

Category: Electronics

Tags