Upgrade your Samla 22 L Box to 4 !! Plusament 1Kg Spool with 7,6 cm !! width
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Es gibt fast immer Vorlagen mit nur 3 Spulen und die Vorlagen für 4 Spulen sind keine Spulen mit 7,6 cm Breite
- Rating
- 0 / 5
- Likes
- 7
- Downloads
- 47
- Makes
- 0
- Views
- 1,059
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Accessories
- License
- Creative Commons — Attribution — Share Alike
Upgrade your Samla 22 L Box to 4 Plusament 1Kg Spool with 7,6 cm width
A description in English is given below
Eine Ikea Samla 22 L Box für wirkliche vier 1Kg 7,6 cm breite Filament Spulen.
Es gibt fast immer Vorlagen mit nur 3 Spulen und die Vorlagen für 4 Spulen sind aber keine (Prusa -) Spulen mit 7,6 cm Breite sondern es ist immer ein Mix aus Spulen.
Es hat mich „etwas“ geärgert nachdem ich jetzt wieder eine Vorlage für 4 Prusa-Spulen gedruckt habe und doch keine 7,6 cm breiten Prusament Spulen passten. Sie sind nur ETWAS zu breit. Wenn man sich nun aber die Box genau anschaut stellt man fest das die Wände der Box nicht senkrecht sind! Unten also schmaler als oben.
Diese Differenz sollte doch ausreichen ? !
Ich habe also aus mehreren Vorlagen eine „neue“ Vorlage entwickelt in der ich wirklich 4 Spulen mit je 7,6 cm Breite in eine Samla 22 L Box bringe.
Einige Teilen habe ich erst selber gemacht ……
aber warum das Rad neu erfinden ? Ich habe Teile aus folgenden Vorlagen verwendet:
und später aber gesehen das es diese bei vielen Dry Boxen aus dem Netz schon gibt. Also habe ich diese, falls jemand seine Box erweitern möchte, übernommen.
Ich habe dafür die folgenden Vorlagen verwendet:
„1“: Auf die Idee es zu probieren brachte mich https://www.printables.com/de/model/176635-filament-dry-box-ikea-samla-22l-base-tower-20-25-m
mit dem Update V3 22.6.2022:
25mm version to save material, weight and print time
Er hat die Achshöhe mit einem
„2“: remake von https://www.printables.com/de/model/116955-filament-dry-box-4x-ikea-samla-22l verändert um mehr Platz für seine SilicaBox zu bekommen.
Ich habe den Vorschlag von „1“ für „2“ probiert und damit wieder etwas mehr Platz erhalten -- aber zu wenig. Von „2“ habe ich die Base-Plate sowie die Thumb Screw_x16-9x verwendet.
„3“: https://www.thingiverse.com/thing:5274996
Allerdings habe ich in „3“ noch die „Bearing-Disc.stl“ gefunden und verwendet.
Die Verwendung von 8 „Bearing Housing 16x.3mf“ von „2“ je Seite benötigt zuviel Platz .
Ich habe also 8 Kugellager je Seite mit 8 Scheiben von „3“ als Seitenbegrenzung verwendet und damit wieder etwas Platz gewonnen.
Die Thumb Screw_x16.3mf von „2“ habe ich original übernommen.
Die „End Cap for Threaded Rod_4x“ sind im Durchmesser zu groß für die schrägen Wände
Nicht probiert:
Fünf dieser „Bearing Housing 16x.3mf“ je Seite ( in der Mitte liegen also jeweils 2 Kanten der Spulen auf einer „Bearing Housing 16x.3mf“ gehen auch. ABER
1): Achtung: meine Body Unterlagen müssen damit aber in der Höhe um 3 mm reduziert werden. Die Unterlagen habe ich noch nicht mit geringerer Höhe getestet sie sind aber leicht im Slicer mit Z zu ändern.
2:) Ich habe aber die „Bearing Housing 16x.3mf“ nicht verwendet weil ich befürchte das die volle Spule evtl. die fast leere Spule über die Reibung bei nur einem Kugellager abwickelt. ( habe ich nicht getestet ! Danke für jede Rückmeldung.)
Die Erkenntnis aus diesen Versuchen war nun einfach. Die Achse muss höher gelagert werden! Also habe ich diese durch Unterlagen auf 17mm erhöht bis gerade 4 Spulen a’ 7,6 cm passten.
„4“: https://www.thingiverse.com/thing:2798409
„5“: https://www.thingiverse.com/thing:2110134
Der Deckel der Box hat - bei mir mit einer Dichtung im Deckel !!!- nur noch ca 1-2 mm Abstand. Ich verwende Klammern am Deckel nach „4“ oder „5“ die etwas zur Stabilität der Box beitragen.
Die Klammern nach „5“ halten aber wohl fester für mich.
„6“: https://www.printables.com/de/model/47745-silica-gel-boxes-with-snap-on-lid-parametric
Die SlicaBox aus „6“ habe ich auf 10x18x1,5 cm mit der beiliegenden Freecad Datei geändert.
Auch habe ich eine Anleitung zur Regeneration von Silica Gel von meinem Shop beigelegt.
Für die Filament Durchführungen ( M6 and M10 PTFE push fitings ) habe ich mir schnell Schrauben mit Feingewinde M6 bzw. M10 gemacht und eine Mutter mit kleinem Ansatz.
Einfacher war es aber diese Teile einfach zu übernehmen von
„7“: https://www.thingiverse.com/thing:6597616
modified Bowden_Clip_v3-0_Threaded-for 8mm rod - 6597616
„8“: Samla PC4-M6 sidewall Adapter by malk0000 – Thingiverse.pdf
Der Link scheint tot zu sein deshalb lege ich die Dateien hier hin
„9“: https://www.printables.com/de/model/465787-samla-drybox-pc4-m10-ptfe-fitting-passthrough
Weiterhin habe ich von „3“ noch die „Bearing-Disc.stl“ einfach aufgesägt um sie über die eingebaute Gewindestange schieben zu können. Hierfür könnte PETG aber besser geeignet sein als PLA das ich für alle anderen Drucke verwendet habe.
Die Clips nach „7“ werden benötigt um Spulen mit weniger als 76 mm nachträglich einsetzen zu können ohne alle Schrauben vorher zu demontieren.
Die 2 Kugellager kann man nun trennen und dennoch eine Seitenführung für andere Spulen haben. Die Clips nach „7“ werden dann stark an die Seiten gedrückt und statt der Thump nuts zur Befestigung verwendet. Die Kugellager dürfen nicht wackeln. see picture.
Alle Teile mit Gewinde sollten besser mit 0,15 statt 0,2mm gedruckt werden.
Auf einen Kommentar, Make und Remix von Euch freue ich mich.
Meine alte Box habe ich montiert / geändert mit:
a:) Die Base besteht aus dem „Base Tower 25mm hoch“ , original „Base Body“ und meine „Body Unterlage 17 mm“ hoch. „Base Body“und meine „Body Unterlage 17 mm“ kann man zusammen kleben -- habe ich aber nicht.
b:) zwei längeren M8 Gewindestange ( bitte genau 345 !! mm ).
c:) am Ende der Stangen verwende ich die „Thumb screw“ mit je einem Spacer von 3mm zur „Bearing-Disc.stl am Kugellager .
Die erste Thumb srew wird bündig zur Gewindestange ausgerichtet. Der Rand der Spule auf dem Kugellage sollte jetzt mit ca 1mm Abstand zur Box laufen können. Danach werden alle anderen Einzelteile aufgesetzt und zur ersten Thumb screw ausgerichtet.
mit der zweiten „Thumb screw“ und dem Spacer die Gewindestange nur lose einspannen. Die Box darf sich nicht verformen! Die andere Gewindestange von der gleichen Richtung montieren falls die Stangen nicht genau ( gleich ) waagerecht im Base Tower liegen, auch um die Oberflächen der Lager wirklich parallel zu haben.
Die „End Cubs“ aus „2“ können wegen der schrägen Wände und der größere Durchmesser nicht verwendet werden.
Die Einteilung der mittleren Kugellager ( Anzahl der Rollen zusammen mit den Möglichkeiten der Seitenbefestigungen ) sind in den (nicht immer aktuellen) Bildern zu sehen.
Die Ränder der Spulen zur Box sollten nur einen kleinen Spalt haben.
Die Ränder der Spulen sollten (bei 76mmSpulen) möglichst genau über den Berührungsschlitzen der 2 Kugellager liegen. Jetzt sollten alle 4 Spulen „fast“ (1mm?) ohne Berührung leicht drehbar in der Box liegen und zum Deckel mit der Dichtung !!! und den Klammern ca. 1-2 mm Luft haben.
Wenn man nun auf den Deckel leicht über den Rändern der Spulen drückt merkt man den kleinen Abstand. ( siehe MP4 Video ) Von der Seite sieht man den kleinen Spalt zwischen den Spulen.
Wenn unterschiedlich breite Spulen verwendet werden sollen können zur leichten Verstellung ein mix der Thumb Screws ODER Clips mit den schmalen „Bearing-Disc“ genutzt werden die aber vorher mit einem Schlitz 2mm versehen werden. Ich habe dies einfach mit einer Schere für Metall gemacht. Der Clip kann dann durch drehen fest gegen die „Bearing-Disc“ gedrückt werden! Das Kugellager darf nicht wackeln.
d:) die nicht genutzten (4 alten) Filamentzuführungen habe ich mit kleinen Schlauchabschnitten, deren Loch verklebt wurde, verschlossen.
e:) Die auch die offenen Filamentrückführungen „8“ habe ich mit kleinen Schlauchabschnitten, deren Loch verklebt wurde, verschlossen. Für die 4te Filamentrückführung habe ich unten, zwischen den vorhandenen, ein 10mm Loch gebohrt.
Die Schläuche gehen bei mir bis zum Drucker deshalb muss das Filament nur wenig in die Rückführung eingeschoben werden. Ich habe von „8“ die PTFE 10mm Schrauben eingebaut.
f:) der Deckel benötigt eine selbstklebende Dichtung um auch mehr Platz zu den Spulen zu bekommen !!!!
G:) Als Klammern für den Deckel habe ich die von „5“ verwendet
h:) die Silica Box habe ich auf 100x180x15mm geändert. Sie kann lose an die Rückwand gestellt werden. Sie kann so leichter gewechselt werden.
I:) für Temperatur und Hydro ist ein Rahmen beigefügt.
Ich hoffe die beiliegenden Fotos (nicht immer aktuell) erklären den Aufbau auch.
Alle Teile mit Gewinde sollten besser mit 0,15 statt 0,2mm gedruckt werden.
Über einen Kommentar, ein Make, ein like oder ein Remix von Euch freue ich mich.
Und: don't hesitate to contact me
________________________________________________________________________________
An Ikea Samla 22 L box for four 1 kg 7.6 cm wide filament spools.
There are almost always templates with only 3 bobbins and the templates for 4 bobbins are not (Prusa -) bobbins with 7.6 cm width, but it is always a mix of bobbins.
I was "a little" annoyed after I printed another template for 4 Prusa bobbins and still no 7.6 cm wide Prusament bobbins fit. They are just a LITTLE too wide. But if you take a closer look at the box, you will notice that the walls of the box are not vertical! So they are narrower at the bottom than at the top.
This difference should be enough? !
So I developed a "new" pattern from several templates, in which I actually put 4 bobbins, each 7.6 cm wide, into a Samla 22 L box.
I made some parts myself first, but why reinvent the wheel? I used parts from the following patterns:
"1": I got the idea to try it at https://www.printables.com/de/model/176635-filament-dry-box-ikea-samla-22l-base-tower-20-25-mm
with the update V3 22.6.2022:
- 25mm version to save material, weight and printing time
- He changed the axle height with a
"2": Remake of https://www.printables.com/de/model/116955-filament-dry-box-4x-ikea-samla-22l to get more space for his SilicaBox.
I tried the "1" for "2" suggestion and got a little more space -- but not enough. I used the base plate and thumb screw_x16-9x from "2" and the Base-Tower 25mm from „1“.
"3": https://www.thingiverse.com/thing:5274996
However, I found the "Bearing-Disc.stl" in "3" and used it.
Using 8 "Bearing Housing 16x.3mf" from "2" per side takes too much space.
So I used 8 bearings per side with 8 disks from "3" as side limits and gained some space again.
I used the original thumbscrew_x16.3mf from "2".
The "End Cap for Threaded Rod_4x" are too large in diameter for the sloped walls.
Not tried:
Five of these "Bearing Housing 16x.3mf" per side (in the middle there are 2 edges of the coils on each "Bearing Housing 16x.3mf") also work. BUT
1): Attention: The height of my body mounts has to be reduced by 3mm. I have not tested the lower height supports yet, but they are easy to change in the slicer with Z.
2:) I did not use the "Bearing Housing 16x.3mf" because I am afraid that the full spool might unwind the almost empty spool due to friction with only one ball bearing. (I did not test this! Thanks for any feedback).
The realization from these tests was now simple. The axle has to be mounted higher! So I raised it to 17mm with supports until 4 coils a' 7.6 cm fit.
"4": https://www.thingiverse.com/thing:2798409
"5": https://www.thingiverse.com/thing:2110134
The lid of the box - in my case with a seal in the lid !!! - has only a gap of about 1-2 mm. I use clamps on the lid after "4" or "5", which contribute to the stability of the box.
However, the clips after "5" probably hold better for me.
"6": https://www.printables.com/de/model/47745-silica-gel-boxes-with-snap-on-lid-parametric
I have modified the SlicaBox from "6" to 10x18x1.5 cm using the attached Freecad file.
I also added instructions for regenerating the silica gel from my shop.
For the filament feedthroughs (M6 and M10 PTFE connectors) I quickly made screws with a fine M6 or M10 thread and a nut with a small shoulder.
However, it was easier to just take these parts from
„7“: https://www.thingiverse.com/thing:6597616
modified Bowden_Clip_v3-0_Threaded-for 8mm rod - 6597616
"8": Samla PC4-M6 Sidewall Adapter by malk0000 – Thingiverse.pdf
The link seems to be dead, so I'll put the files here
"9": https://www.printables.com/de/model/465787-samla-drybox-pc4-m10-ptfe-fitting-passthrough
I also sawed open the "Bearing-Disc.stl" from "3" to be able to slide it over the built-in threaded rod. PETG might be better for this than PLA, which I used for all the other prints.
The clamps after "7" are needed to be able to insert spools with less than 76 mm without having to remove all screws first.
You can now separate the 2 ball bearings and still have a side guide for other reels. The clips after "7" are then pressed firmly against the sides and used instead of the nuts to secure them. The ball bearings must not wobble, see picture.
All parts with threads should be printed with 0.15 instead of 0.2mm.
I look forward to your feedback, makes and remixes.
I have mounted / modified my old box with:
a:) The base consists of the "Base Tower 25mm high" original "Base Body" and my "Body Underlay 17 mm" high.
"Base Body" and my "Body Underlay 17 mm" can be glued together -- but I didn't.
b:) two longer M8 threaded rods (exactly 345 !! mm please).
c:) at the end of the rods I use the "Thumb-Nut" with a spacer of 3mm each to the "Bearing-Disc.stl on the ball bearing.
The first thumbnut is flush !! with the threaded rod. The edge of the coil on the bearing should now be about 1mm from the box. All other parts are then fitted and aligned with the first thumbscrew.
Using the second thumbnut and the spacer, loosely clamp the threaded rod.
Do not deform the box!
Mount the other threaded rod from the same direction if the rods are not exactly (equally) horizontal in the base tower, also to ensure that the surfaces of the bearings are really parallel.
The "End Cubs" from "2" cannot be used because of the sloping walls and the larger diameter.
See the (not always current) pictures for the arrangement of the middle ball bearings (number of rollers together with the possibilities of side mounting).
There should be only a small gap between the edges of the coils and the box.
The edges of the bobbins (for 76mm bobbins) should be exactly over the slots of the 2 ball bearings.
Now all 4 coils should "almost" (1mm?) rotate easily in the box without touching and should have about 1 to 2 mm clearance to the cover with the seal !!! and the clamps.
If you now press the lid slightly over the edges of the coils, you will notice the small gap. From the side you can see the small gap between the coils.
If you want to use coils of different widths, you can use a mix of the knurled nuts AND / or Only Clips and the narrow "bearing disks" for easy adjustment, but you have to cut a 2mm slot in them first. I did this easily with metal scissors. The clip can then be pressed firmly against the "Bearing-Disc" by turning it! The bearing should not wobble.
d:) I sealed the unused (4 old) filament feeds with small pieces of tubing, the hole of which was glued.
e:) I also sealed the open filament returns "8" with small pieces of tubing, whose holes were glued. For the 4th filament return, I drilled a 10mm hole at the bottom between the existing ones.
The tubes go all the way to the printer, so the filament only has to be pushed a little into the return. I installed the PTFE 10mm screws from "8".
f:) the cover needs a self-adhesive seal to get more space for the spools !!!!
g:) I used the clamps from "5" for the cover.
h:) I changed the Silica quartz box to 100x180x15mm. It can be placed loosely on the back wall. This makes it easier to change.
i:) A frame for temperature and hydro is included.
I hope the enclosed photos (not always up to date) explain the assembly.
All parts with threads should be printed with 0.15 instead of 0.2mm.
I would be happy to get a comment, like, a make or a remix from you.
And: don't hesitate to contact me