P
Printablesgeeky.gent
Broadhead Case (SKB iSeries Dimensions)
A tiny bit larger than the SKB case to improve the fit in the SKB bowcases. The original SKB box slides out pretty much every time, mine doesn't.
- Downloads
- 418
- Likes
- 64
- Rating
- 5
All models
Counting matching models…
P
Printablesgeeky.gent
Fender Stratocaster Gotoh Tuner Drill Jig
As a side-note: Be careful if you are working with roasted maple! While tightening the screws my headstock cracked. Nothing that wasn't fixable with glue and a jig, but still a word of caution. My designs are released under a public…
- Downloads
- 128
- Likes
- 38
- Rating
- 0
P
Printablesgeeky.gent
Leatherman Sidekick Thumb Buttons
The knife is 2mm strong, the saw 0.8mm. I wanted the additional height of the thumb buttons to be subtle and not super thick. I opted for one millimeter. You can adjust the parametrized Fusion 360 file in case you would want more…
- Downloads
- 122
- Likes
- 18
- Rating
- 4.5
P
Printablesgeeky.gent
Smart Tag 2 Rigid Case
Designed for PETG. Don't forget to rescale if you change material to TPU 95A (I recommend to start with a factor of x1.02) Design allows for more temper-proof installation, because the screws can be contained Case Dimensions: 80.8mm X…
- Downloads
- 97
- Likes
- 17
- Rating
- 0
P
Printablesgeeky.gent
CZ 457 Varmint MTR Buttstock
To attach this stock start by compressing the bottom part of the rubber stock and slide it over the top. Stays in position well without any glue. My designs are released under a public domain license: You can do whatever you want with…
- Downloads
- 90
- Likes
- 7
- Rating
- 0
P
Printablesgeeky.gent
Hollyland Lark M2 Microphone Holder
Included a parametrized Fusion360 file in case you want to adjust thickness or length of the grip. You will need a 10mm diameter magnet with a depth of 2mm. My designs are released under a public domain license: You can do whatever you…
- Downloads
- 64
- Likes
- 8
- Rating
- 0
P
Printablesgeeky.gent
Ikea Kallax Cable Routing
Cleanly route cables behind your Kallax. You'll need support for this print unless you find a way to split it elegantly. Keep in mind that those cable routing pins are not too rigid when they are printed perpendicular to the layer lines.…
- Downloads
- 44
- Likes
- 10
- Rating
- 0
P
Printablesgeeky.gent
Magnetic DE Razor Blade holder (straight & angled version)
Disclaimer: Blades are magnetic; be extra careful when you change them. Use at your own risk. Don't be stupid. Designed with ease of use and ergonomics in mind; NOT with heavy-duty use. I use it to score self made bread and buns before…
- Downloads
- 42
- Likes
- 8
- Rating
- 5
P
Printablesgeeky.gent
HX Stomp Backplate
Disclaimer: I ended up not printing it because I found a different solution to what I had planned. I attached the Fusion file with all the parameters so you can edit it to your needs. I am certain the dimensions are correct. I would be…
- Downloads
- 40
- Likes
- 5
- Rating
- 0
P
Printablesgeeky.gent
Drywall fix for failed drywall anchor (1/2in)
I hit a stud with a drywall anchor and cleanly chewed a 1/2in hole into the wall. This print fills the hole and allows you to screw a 4mm diameter woodscrew directly into the stud. My designs are released under a public domain license:…
- Downloads
- 39
- Likes
- 7
- Rating
- 0
P
Printablesgeeky.gent
Ergonomischer Pelmeni Stecher
Print in food-safe filament and add fuzzy skin on the outside. If the dough sticks to the inside, polish the layer rings with some sandpaper. You may adjust the size by using the attached Fusion360 file. My designs are released under a…
- Downloads
- 35
- Likes
- 2
- Rating
- 0
P
Printablesgeeky.gent
Attractive Fan Duct
Connect four 120mm fans to any opening that fits two. I used fans that I had lying around, but I would recommend going for pressure optimized fans if you have the choice. I use this to get additional circulation for a walk-in closet. All…
- Downloads
- 35
- Likes
- 15
- Rating
- 0
P
Printablesgeeky.gent
Yeti Lid Holder
My designs are released under a public domain license: You can do whatever you want with them. I put as much care and attention to detail into them as if they were commercial products. If my design solved a problem for you, I'd like to…
- Downloads
- 33
- Likes
- 7
- Rating
- 0
P
Printablesgeeky.gent
Ikea Lack Rack Mount (45mm unit height)
I recommend PETG and a high infill percentage. Don't forget to clone and mirror both parts before printing. Additional Requirements: 8x4mm wood screws Sidenote: If you have kids around I would recommend to round off the sharp edges. I had…
- Downloads
- 26
- Likes
- 6
- Rating
- 0
P
Printablesgeeky.gent
STM 32 Bluepill Case
DISCLAIMER: 1. I am not affiliated with the FreeDMO project , but it is awesome and this is my case for the STM32 board. 2. In its current version the case does not fit into the Dymo550 because of its height. I attached a Fusion360 file…
- Downloads
- 22
- Likes
- 4
- Rating
- 0
P
Printablesgeeky.gent
Dymo Printer Spool
Use it either as an replacement part, or attach an RFID chip to feed your jailbroken dymo information about off-brand label sizes. I also added a Fusion360 file in case you need to make changes. My designs are released under a public…
- Downloads
- 19
- Likes
- 2
- Rating
- 0
P
Printablesgeeky.gent
Ikea Bror Shelve Foot
Printed in TPU95A with 100% infill 2 models: One closely modeled after the original and one with additional support area to reduce footprint on floor Comes with parametrized Fusion 360 file in-case you want to edit it. My designs are…
- Downloads
- 19
- Likes
- 5
- Rating
- 0
P
Printablesgeeky.gent
D'Addario Guitar String Organizer
The fusion file is attached, but the count parameter has not been tested and you would have to add additional step heights. You should be able to figure it out relatively quickly, though. My designs are released under a public domain…
- Downloads
- 16
- Likes
- 3
- Rating
- 0
P
Printablesgeeky.gent
Curtain Holder (Sew-in)
The packages these are sold in have 2-3 items too little to finish a curtain. We didn't want to purchase another package, so I recreated them. Printed with Bambu Basic PLA on its side and working well. My designs are released under a…
- Downloads
- 13
- Likes
- 2
- Rating
- 0
P
Printablesgeeky.gent
Spark Go USB Dust Protector
Printed in PLA. Scale up if you print in PETG / TPU. My designs are released under a public domain license: You can do whatever you want with them. I put as much care and attention to detail into them as if they were commercial products.…
- Downloads
- 11
- Likes
- 3
- Rating
- 0
P
Printablesgeeky.gent
Strymon- / Keeley-Pedal Divider
While the model is 1mm thick, I would suggest just printing the first layer to have a super thin and flexible divider. I also added the Fusion360 file in case you'd like to make some edits. My designs are released under a public domain…
- Downloads
- 10
- Likes
- 3
- Rating
- 0
P
Printablesgeeky.gent
Tweezers (guided- / unguided version)
As you can imagine from the summary text this is a very quickly thrown together design. No other tweezers here on Printables looked like I wanted to use them on my eyeball… This did the job. I am not responsible for what you do with it.…
- Downloads
- 8
- Likes
- 3
- Rating
- 0
P
Printablesgeeky.gent
Canakit NF-A4x10 Raspberry Pi 5
The model is not 100% finished: The corner rails of the lid don't fit the case at the moment, but you can easily clip them off and then the case works fine. It fit well enough for my usecase so I didn't go back to touch it up. If you want…
- Downloads
- 8
- Likes
- 2
- Rating
- 0
P
Printablesgeeky.gent
VZ-Rock VariZoom Remote Clamp Replacement
My designs are released under a public domain license: You can do whatever you want with them. I put as much care and attention to detail into them as if they were commercial products. If my design solved a problem for you, I'd like to…
- Downloads
- 6
- Likes
- 2
- Rating
- 0
P
Printablesgeeky.gent
Art Pro Audio Magnetic Mount
Print in either PETG or TPU. Use 100% infill. PLA will break don't bother. 2x6 ø10mm x 2mm depth magnets needed. You could get away with just using 6 magnets if you want to stick it do a magnetic surface like seen in the pictures. I…
- Downloads
- 4
- Likes
- 2
- Rating
- 0
P
Printablesgeeky.gent
Art Pro Audio X-Connector
I would recommend to NOT print this from PLA because it would be too brittle. I tried both PETG and TPU and they are stable enough. TPU dampens impacts a bit more. My designs are released under a public domain license: You can do whatever…
- Downloads
- 3
- Likes
- 2
- Rating
- 0
P
Printablesgeeky.gent
Aluminum Profile Ladder Feet (Parametric Fusion file included)
The 2 models included are for a ladder with following profile dimensions: Profile Thickness: 1.7mm Profile Corner Radius: 4mm Outer Profile Width: 20.7mm Outer Profile Height: 33.7mm You can use the fusion file to adjust anything on the…
- Downloads
- 3
- Likes
- 0
- Rating
- 0
These are all currently available results.