Counting matching models…
Design This is a lightweight(under 14 grams) twist lock PTFE disconnect which uses (2) 6mmx3mm rare earth magnets(see below regarding actual thickness) to hold a locking position and (2) PC4M10 or (2) PC4M6 pneumatic connectors. I kept…
5/7/24 - added a 2nd larger version at 130mm wide while the original is 100mm wide. Incense stick holder. 3mm hole is 40mm tall to ensure stick does not lean too far and ashes are caught. The 100mm works decently but the 130 will…
Pegboard plier rack. Mounts using screws.
Designed for: LM2596 buck converter (see image)
Post a make if you print this! :) Seeing our creations out in the wild is inspirational knowing it's helping other folks and encourages creators to put more out there. Needed a velcro anchor. Designed these and mount with 1/2" #6 wood…
This is a remixed version of an airbrush holder. Base was shortened to allow brush to sit in holder, cup resting fully against front edge, with a rigid hose that drops off edge of table surface. Added curved edges on main body. Opened…
Remixed @third-dimension-labs clean WASD keyswitch/cap fidget. Opened up the string hole so it can hold 3/32 paracord. Added a chamfer to the bottom edge. Add your own switches and caps. There are 3d printed caps on this site.
tl;dr - use this altered BSPT(British Standard Pipe Thread) to design openings to accept a PC4M10 connector with threads that correctly accept said PC4M10 connector, seat correctly and don't cross-thread a few threads in and cut their own…
Needed some fishing weight sliders so made some up. Hole is filleted to avoid abrasion on fishing line. Print with as many perimeters as needed to make solid. Print at high end of temp range in PETG or ASA for a solid piece. I'm using…
Please post a make if you make this! :) Demo of print status screens: https://imgur.com/a/yX2dhjJ Compact Case for Wemos D1 mini wifi ESP8266 with 0.96 Inch Yellow and Blue I2C IIC Serial 128X64 OLED Display . Uses (1) 10mm M3 screw for…
Needed a ¼ and ½ tsp for my Miracle Gro for my garden so designed this. No support, print with PETG. Long reach but short enough to fit in a canning jar for storage with fertilizer.
Apple Watch stand that fits a gen 6 charger cable. Small friction fit extrusions on the side of the charger opening secure the charger in the holder. Press in to place. I redesigned this from scratch using the old mesh to measure/trace…
Remixed the R17 Ultimulti version of the idler to remove rattling sound when idler moves. Remix of the original Prusa standard idler version here . Print as oriented. This remix adds a .5mm bearing spacer to each wall of the bearing slots…
Not mine but found the old stl file and didn't see it on Thingiverse so uploading here. For use with hex tiles. Compatible with Heroscape. Category: Buildings & Structures
Another grab handle. Print on it's side with supports enabled everywhere and block supports except the top bolt opening. I am using this outdoors and wanted the water to be able to drain away from the bolt vs a hole for the bolt that…
Remixed the standard R4 version of the idler to remove rattling sound when idler moves. Remix of the Ultimulti version here: https://www.printables.com/model/893656/ Print as oriented. This remix adds a .5mm bearing spacer to each wall of…
Post a make if you make this! :) I liked the Fortnite sign and idea of a light box and wanted to change a few things so I remixed this. Built a new box and diffuser and remixed the faceplate. This uses (4) 20mm M3 screws. There's a…
This is a cap to install over the opening of the backup alarm on the 14th gen Ford F150. This installs with small dabs of silicone adhesive if you want to remove later. I two small drops of super glue which will keep this in place but I…
This may strip out the 3/8" socket (it did with mine) due to the torque required in the small hole. The hand-grip style may be more successful. This is an oil filter removal tool for the Motorcraft FL-500S filter which comes in two…
This is a fidget toy that uses 608(typical skate 8mm x 22mm x 7mm) bearings. You can buy the cheap ones for this application. This is not load bearing like a skateboard or scooter. There are cheap bearings on Amazon for down to 20 cents…
Open back switch housing for a 21mm x 15mm rocker switch . Uses (2) #6 wood screws to mount. I used ½" screws to mount this in my lack enclosure. Loop your wire in the back and secure with a blob of hot glue from a hot glue gun for strain…
Edit - I've used this for six months now and I don't have any desire to redesign stuff. It's worked out really well! My Hakko does not come out nearly as much with this solution at hand for small projects. This is a Pinecil case I…
I remixed 3d_aubs glasses to use M3x4mm bolts in the hinges (just screw them in to self-tap). Also increased the size of the hinges slightly for better durability. Print with the arms top edge down, with supports, so you get a clean…
A tool belt bracket to hold a Ryobi cordless drill. Modeled against the P208 model. Fits a 2" tool belt. The vertical tabs are actually 5mm taller than in the image. I added some height to the design but not reprinting at this time but…
Soaker hose spike to keep my soaker hoses in place. Designed a barb at the bottom to help keep in place. Printed using draft mode for .3mm layers(thicker layers are more durable), three perimeters, high end of PETG range for strength.
This is a set of sorting trays I made for my maker space. I found myself needing small containers often and decided to design a few small trays. Exported from Fusion360 CAD in high resolution(smooth curves). Internal curve is for smooth…
Uploading to make sure this legendary offline Rex bling lives on here. Print as oriented. Scale as needed. 100% is 225mm x 83mm x 20mm(same in pic).
Remixed Xlnt3D's nicely designed rear TT-02B shock tower ( https://www.thingiverse.com/thing:4494409 ) so I could use my stock screws. This is a great replacement to add rigidity to the rear shock tower so your shocks can do their job.…
Remixed the MK3s+ fan shroud to add a few partitions to ensure air splits up to flow out the side vents. Not sure the impact of this but it doesn't seem to hurt. :)
This is a remix of an easy to print sample spool. This is one of the spools out there with threads that have a bit of a steep overhang but still print cleanly. Changes include: thickened sides as they felt thin/breakable widened spool to…
This is a wire shelf sleeve to be used in pairs to support wire shelves which have posts that measure 17.77mm in diameter. This sleeve has a single ridge. This piece will work with existing sleeves that came with the shelf. For your own…
Falcon2 Pro Collection This is a holder for a 5V 5mW laser crosshair pointer for the Creality 22w/40w/60w laser module used to line up material on the bed for cutting accurately and set back far enough so as to not collide with the front…
This is a wall mount bracket to hold a macbook pro or other thin laptop. Mounts on screws on a board or wall surface. I put a small piece of double sided tape on the back surface, toward the bottom as well so I slide the bracket onto the…
Plastic hardware for hanging wire shelves. Two bracket sizes depending on shelf design(face height). Rod gaps are 7mm. Measured wire size on my shelving was 6mm. Print in PETG with 10 perimeters and 90% infill for nearly solid hardware at…
My son wanted a solid version of https://www.thingiverse.com/thing:3447951 so I cleaned it up in Fusion 360 to make it solid (non-flexi). Print Settings Rafts: No Supports: Yes Notes: Supports for the ears. Print on it's side. Category:…
This is a bar end plug for a BMX handlebar. Note render of .3mf looks odd since there's a cylindrical ‘print setting’ modifier in there as well(see below). Plug has 18mm outer diameter with a wedge that can secure into a 19mm opening.…
This is a duct to cool an RTL SDR device. This uses: (4) FYSETC stepper motor heatsinks (4) 10mm M3 bolts (self threads into duct) (1) 30mm Raspberry Pi fan Print as stl is oriented, fan opening down. Prints without supports. Install heat…
4/27/25 - Added an easy load tray. Insert this in place between the top and bottom and you can then load your filament by pushing into the PTFE tube to reach the MMU without removing the top of the buffer. Once all filament is loaded,…
Square incence holder. Angled to drop ash in to tray and minimize foot print. No supports needed.
7/26/25 - update - added a version with stand-off feet so you can orient this facing upwards. Need intake area. Print with supports. everywhere on build plate. Organic remove nicely via Prusa Slicer. Uses these bumpers for feet (buy the…
This is a lightweight(under 15 grams) PTFE disconnect which uses (2) 6mmx3mm rare earth magnets(some measure 2.7 mm thick while others measure 3mm thick - measure your magnets - two designs are available below)and (2) PC4M10 neumatic…
Air tool quick release holder rack. Two and four count. Mounts with screws. No supports required. Print in PETG at the high end of the temperature scale (250C) for good layer adhesion with four perimeters for durability.
Edit - mine has been replaced with a new design to use current COB LED strips with a PWM dimmer: https://www.printables.com/model/870280-cob-led-strip-housing-use-for-lack-or-other-enclos Post a make if you make a set! :) I needed to…
Remixed GerryPB's metric radius gauges with larger font labels. Print in two color layers for labels to stand out better.
This is a servo controlled duct I use for my printer exhaust (120mm fan to 4" flex duct) which goes in to an attic space. The hot/cold air from the attic gets pulled into my enclsoure and my home from time to time with air pressure…
Found this GCODE a few years back and found it very useful for cleaning/lubricating my smooth rods. Demo: I use this stuff: https://www.amazon.com/Super-Lube-21030-Synthetic-Grease/dp/B000XBH9HI/ Blurred out in pic as I'm not advertising…
This is a holder for a ½" schedule 40 PVC pipe. There is a flange in the bottom. This secures with (6) construction screws. Using this to hold a shade screen up for my vegetable / flower starters in the Spring. Two .stl versions - one…
Falcon2 Pro Collection A TPU brace to hold your slats in place so they don't shift around when putting material on the bed to cut precisely. Print two sets to fully cover the slats in any orientation. Print as oriented. Default FLEX…
This is a rounded larger knurled rotary knob for the MK4(s) LCD panel. Supports on bed only - easy to remove with needle nose pliers Seam - random - else they align and are visible on the smooth face of the knob Print at .15 layer height.…
This is a razor blade handle with a face that enables you help release prints from your bed. The angle of the razor is perfect to not cut the bed or print which makes it very effective at getting under prints to start the release of them.…
Print with supports in PETG. You can forego supports and test your printer's bridging. :) Mounts using a few smaller wood screws.
Remixed the strongest pegboard clip I've seen to make it a bit more sturdy and added removal openings
This is a splice to repair a soaker hose. The inner diameter of my soaker hose was roughly 15 mm. This pushed in to place and did not leak. Time will tell. Also created an end cap. Printed in PETG with three perimeters on the higher end…
You can get these online but why not print your own. Print both the clip and weight at 90% gyroid infill in PETG yeilded roughly 5 grams each. The weights mount using double sided tape. If you need to color match, craft stores carry cheap…
LED diffuser strip for UltiMulti MMU remix printed in black/clear. You can print in a single color for sure(clear) but thought maybe the black between the lenses would help isolate light to each position.
I build this qi charger so I could charge while viewing on my night stand but also found I could print the body/back pieces, glue them together with super glue and mount it on a vertical surface using double sided tape. I also wanted…
A spring base came off my son's TT-02B car somehow so I designed and printed this replacement and it works great. Print as stl is oriented with supports for the inside. This way the spring perch area is sharpest. Print Settings Rafts: No…
This is a keeper for loose ends of webbing on a backpack so they're not flopping around. This is made for (2) pieces of 20mm webbing. If it's tight, you can scale it's width in the X axis in your slicer. This is firm on an Osprey pack I…
Remixed the base to include flat head screw mount tabs. the hole is 4mm. The tapered area diameter is 8mm.
This is a minimum zip tie mount that mounts using a #6 wood screw. The opening in this bracket is for use with the mini zipties that came with the Prusa. The cross section of this zip tie is 1mm x 2.6mm. The hole is low and has raiduses…
Print all parts as oriented - no supports. This is a reusable cardboard sign holder that uses cheap PVC for a handle. You can use the included friction fit handle but bike grips work as well and can help folks who may find it…
Falcon2 Pro Collection I had smoke creeping out the crack between the exhaust hose adapter and the side of the enclosure as well as the hose connection where the wire wraps. I replaced the fan grill with this foam gasket cut from 2mm…
I remixed this awesome design by @Dustin to enable MMU3 printing on the same layer. Printed on a textured print sheet to help hide any layer lines. If printed on a PEI smooth sheet, you can touch it up with a heat gun to get rid of any…
Bungee ball bracket for patio shades. I designed this so I could have bungee ball holders at different heights. Mid height allows you to see your yard but offer privacy. Lowest height helps with weather protection. The replacement bar end…
Print as oriented. Assemble by inserting (6) 1cm pieces of filament in one half. Check fit into other side to ensure filament pieces are short enough. Then apply super glue to one face and clamp to set up. Old handle needs to be removed.…
Falcon2 Pro Collection This is a door exhaust port I use for my laser cutter/engraver which uses a 75mm/3" hose. My door is 44.5 mm thick. You will need to print this: door_exhaust_port and one of these sets exhaust_director_short or…
Falcon2 Pro Collection This is a set of half fan intake shrouds to help the laser unit not pick up particles from the surface being worked on to minimize build up in the cooling unit. Creality does provide instructions on how to pull the…
Please post a make if you make one! :) Two relay type / size boxes are available here... regular and an optocoupler relay. The optocoupler better isolates the relay control from the rest of the board is how I've read it. I've not had any…
Falcon2 Pro Collection This is a magnetic hold down for metal honeycombs for laser cutters. This accommodates 1-4mm thick material and has mm height legends on the top side for reference. Need more force to hold down a warped sheet? Place…
This is a VESA mounting adapter to adapt a 24" sceptre monitor to a 75mm vesa mount. This uses M4 threaded inserts and M4 bolts. This uses a friction fit - ensure your extrusion multiplier is dialed in or this will be too tight. Printed…
Falcon2 Pro Colletion This is a bracket that can be used to build a shelf that sits on top of your Creality Falcon2 Pro enclosure to provide some extra room for a laptop or the like. Two files - one with holes for rubber feet , one…
Github - complete build guide with .stl files - https://github.com/jurassic73/split89 All build details are at the URL above. ( github is easier to maintain vs a build guide on prusaprinters ) This keyboard build was inspired by the…
5/26/23 - redesigned perch to install with a single screw - created template to mark hole to remove material with a dremel - added an installation brace which makes building the tube easier - added a chamfer to the top for easier tube…
PWM controller enclosure for this device: https://www.aliexpress.us/item/3256801762069684.html Print as oriented. No supports required. Two enclosure options. One has tabs to accomodate a #6 wood screw. Use 10mm M3 bolts to secure cable…
Post a make if you make one! :) Remixed SG-O's mount to mount on the wall. There are some other versions of this wall mounted Vive controller holder/charger, however they are not as durable/sturdy as I'd like. These mount with two screws…
Used PETG. Print with (3) perimeters. Standard infill. High end of PETG temps to ensure solid layer adhesion. Press your keyswitch down and the top will release. This design is much more sturdy and less prone to breaking vs the original…
This is an umbrella holder with a removable tube for when not in use. This is for a 9 degree back. Base is 80mm wide and 140mm tall. Base .3mf has a small base layer added to ensure bed adhesion. Printed with six perimeters on the base…
This is a flared PTFE guide that goes on the end of a PTFE tube to help with insertion of filament into said tube. If I don't have my reading glasses on, this is a nice helper. If you want to do two color pieces, add a filament change in…
This is a compact DC power supply that is powered with AC power. Wanted a lower power and adjustable compact supply to use on my desktop with spring terminals to quickly use with bare wire. No more searching for wall warts of the right…
This is a set of pieces to help the Hyte Y40 intake air make it out the back vs the closest exit. This helps ensure air passed past the GPU/CPU and out the back/bottom more than just the closest exit. I'm not a thermal engineer but this…
This is a shock end I had to make for my son's TT02B car. This measures 20mm total in length. Used PETG for this part. Print Settings Rafts: No Supports: Yes Resolution: n/a Infill: 100 Filament: n/a PETG Notes: I printed this laying down…
This is a tool holder for the Ego electric mower. I pull weeds when I see them while mowing so this keeps my weeding tool handy. M3 screws are self tapping into 2.6mm holes. I installed them with a drill hex bit. Print Settings Rafts: Yes…
Please post a pic if you make this! Note: I am working to create a thinner version of this. Needed bird spikes for the rain gauge on my Ambient Weather WS-2000 station however didn't purchase them. Built this ring that snaps into place.…
This is an adapter to use air compressor ¼" NTP fittings to inflate inflatables. No support required. Rigid filaments work fine. TPU even better for some bit of flex. I installed the NTP fitting with the adapter in a vice so I could fully…
USB power adapter rack for organization and accessibility. Way easier than sifting around a drawer of stuff. Wall mount version has screw recesses and an angled base so it tilts up slightly so the adapter will not fall out. There is a…
This is installed on the Traeger shelf so it doesn't chip the paint away on the legs as it rests against them. These press in to place. Secure with super glue. Print Settings Rafts: No Supports: No Filament: n/a TPU Category: Outdoor &…
Remixed this well designed cord organizer. Thanks to @curby_289762 for the great design and making the fusion files available for remix work. added a hook to hold the outer wrap pushed in inside surface .25mm to tighten on charger block…
This base set is for the Keebio 60%/65% mechanical keyboard kit: https://keeb.io/products/quefrency-60-65-split-staggered-keyboard?variant=16032980861022 7/10/20 Update: Added one piece bases so you can print the bases in one piece if…
After installing canned lighting in a few rooms, I wanted to remove the old style lights from our ceiling fans. Needed to make a cap to cover the opening. Worked out nicely and they blend in. Print Settings Rafts: No Supports: Yes…
HIGH TORQUE SERVO + BLADE CAN CUT YOUR FINGER OFF* DO NOT INSTALL BLADE WHEN TESTING POSITIONING* INSTALL BLADE DURING FINAL ASSEMBLY* I built this since I wanted to try building something using a servo controlled by arduino code. Also, I…
This is a junction box cover with various inner diameters - see stl list. Print in .15 layer height for smooth secure operation as oriented. Use five perimeters for the cover to ensure stem sturdiness. No supports needed.
Added wings to this monoject cap so it can't roll away. For 10mL MonoJect syringes. I use these for synthetic grease and glue and this cap does well to seal off the end.
Designed this to fit the side of my Covermate hot tub cover lifter that didn't have towel hooks. Mounts using the three existing screws. Snaps over bar for secure fit. If you're not sure of the make of your cover lifter, this is designed…
Charge pack rack for Anker battery packs . 4/28/26 - Updated to extend rack more and make holder walls taller. Much more secure for packs. 8/23/23 - Update to extend top of rack 20mm. This way the packs won't tip out as easily. Magnetic…
This is a locking hitch pin cover printed in TPU.
This is an adapter to fit the Ettore squeegy/washer to an extension with the standard Unger extension from Home Depot. This friction fits into the squeegy end. Printed in PETG with three perimeters for strength.
Please post a make if you print one! :) I adjusted @bocam bracket so it would fit on my x-axis motor. I didn't like the way the wire flexes right at the motor so I wanted some kind of strain relief. I had to extend the clip height 4mm if…
These are COB LED light strip mounting reflectors I use for my LACK enclosure. I want light on my printer but to minimize what flows outside the enclosure. There are three types of reflectors to use. 45 degree angle mount which I put on…
Remixed this holder to hold a 10mm wide idler pulley. Use of this idler helps minimize belt ripple in your prints. https://www.filastruder.com/collections/hardware/products/gates-2gt-idler?variant=41017736724551 Gates 2GT Idler Toothed…
EDIT - I no longer use Octoprint(PrusaConnect works great). There is a script below to just run on an Raspberry Pi. This is a two button panel I designed for the front of my IKEA LACK enclosure to control a relay for a power strip via my…
