Counting matching models…
This wall mount is for Dewalt drill style form factors. I've tested it with the Impact, Drill, and Heat gun. In theory it should also work for the wire stripper, larger impact, caulking gun and spotting light. However I don't have those…
Small but mighty wall hanger for the Dewalt pole saw/hedge trimmer combo. Print four to hold the pole saw, hedge trimmer, extension, and base kit. No supports are needed for this print. Petg preferred.
This wall mount pocket holds 10+ cutting wheels for the Dewalt 3" cut-off tool or any other 3 inch discs. Make sure to print it upside down and use light supports for the exposed edge. It has a recessed hold for one mounting screw. Enjoy!…
I've seen many nice printable circular saw wall mounts, however, I've not seen one that allows the saw to sit naturally out from the wall. I designed this print to contour the saws deck and take advantage of the 12mm holes in the back.…
Print on it's back, it shouldn't need supports. This mount contours to the tool and holds it against the wall for easy access.
Wall mount for a Dewalt DCS356B Oscillating Multi-Tool. Spacer included, just level and use 2 screws. Can be printed with PLA / PETG / ABS. I prefer PETG on this mount. Check out the oscillating blade wall mount holder here:…
Sturdy wall mount for the Dewalt DCH273B SDS Rotary Hammer Drill. Built in spacer. Use the spacer to level and install 2 screws. Easy to print. Also is said to work with Makita Hammer Drill DHR171
This design was inspired by hardware fashion. It's just nuts. This prints best flat with no support. Print slow, it should work with standard quarter twenty thread. Two models available, one for horizontal orientation and one for…
(UPDATE) I've added V2 versions of the mount and holster This will help with printing and strength. A Major problem with v1 is the neck of the part is very weak due to the orientation while printing. The V2 version is smaller but a lot…
I designed this adapter for use on my Specialized bike which has a MIK-HD over tire rack. Steps: Print the plate upside down (use small tree supports for overhangs) Print the spring clip on its side (for strength) Insert the Spring Clip…
This wall hanger uses 3 screws to secure the mount to the wall. It will hold the Dewalt tire inflator with or without a battery inserted.
This wall bin holds oscillating tool blades. you can fit many of them in here without issue for easy access. Print with any filament. Check out the Dewalt Oscillating Multi Tool wall mount here:…
Print with back facing build plate. This will create a tall but workable print. Use support for the inside. I printed with PETG while using brim.
This is a multi disc circular saw blade holder. It fits 7 1/4" diameter saw blades. Single recessed screw for mounting. Can use any filament type, I used epetg-hs. Make sure to print upside down with support for best finish. Check out the…
This minimalist wall mount holds a Dewalt cordless battery powered pruner. The screws go through the mount point so the tool is secure, can print with petg / pla doesnt matter as long as your screw is into something sturdy.
I made this simple print to run an Nvidia Tesla P40 outside of my rackmount server as the server doesn't have enough internal space to fit it. The print simply keeps the card upright and locked to the psu so it doesn't slide around. The…
This is another iteration of the Meshtastic Harbor Breeze off-grid solar mod. I created this bracket to support an SMA connector. I've also created an N-Type version which can be found here:…
I bought this PCB antenna https://www.aliexpress.us/item/3256806705201271.html?spm=a2g0o.order_list.order_list_main.53.17931802DPs8Qo&gatewayAdapt=glo2usa for ADSB reception. It's not weatherproof so I made a housing that should keep it…
Use PETG or other outdoor rated filament. PLA will become brittle in the sun. This case is designed to slip over a standard external fiberglass antenna and mounts right on the (mounting) portion of the antenna. There shouldn't be any way…
Redesigned lid slide mount for K1 Max. Raised back and spouted lip for easy insertion. Rounded edges for a classy look. You will need slightly longer screws, that's it!
*DO NOT PRINT WITH CONDUCTIVE FILAMENT* My first two versions of an MCC hanger didn't contain wire management, Third times a charm I guess. This is a minimalistic hanger for Olight magnetic charger bases. It should work with any light…
This case holds a B and Q Station G2 Meshtastic Node with room for a usb cord and SMA connector. There is a cover that pops over the bottom to keep bugs out. The case is water resistant and should be find in rain, snow etc. Slip it over…
This long mount is for the modified Harbor Breeze solar spotlight as seen on hackaday https://hackaday.io/project/194509-harbor-breeze-meshtastic-hack . The modification removes the solar panel from the $9 light and allows it to be…
Unscrew the nut and washer on the SMA connector. put the radio into the case, close the lid and tighten the washer/nut back on. There are two LID variations, 1 with a usr btn whole and one without.
I designed this compact case after I discovered the Lilygo T-Beam S3 Core module can operate as a standalone device outside of the T-Beam Supreme dock. This case comes in 2 parts, a top and a bottom that holds the core in place. The core…
I didn't see any stick holder prints that could hold many sticks for easy access so here goes. Just ziptie it to your kit and cut off the excess tie and your done. Just print it upside down, no supports needed. I made it for small…
I didn't see many cases for the Nano VNA H that could hold all the stuff it comes with so I made this. It has storage inside for calibration tools, pigtails and sylus. The lid friction fits and keeps everything together well enough. Enjoy!
This weather resisant case slips over the stand for an Amazon 5W solar panel. Holds a meshtastic device & battery and slips over the solar panel's mount. The mount is tapered so you can get a good tight fit. You can choose to wire the…
This stand was made for use with these holster based Meshtastic Harbor Breeze solar node designs: SMA: https://www.printables.com/model/1275240-minimalist-sma-harbor-breeze-meshtastic-off-grid-s N-Type:…
I use to balance the light on my charger and was frustrated when it would fall off by being bumped. Insert your MCC magnetic charge dock into this print and hang your Olight from the USB charger. When you print this, make sure to print…
I wanted to mount my node on the shed but had to keep unscrewing to take it down to upgrade the firmware. I made this to compliment my other model that holds a Meshtastic node, 18650, and an antenna.…
Fits the mounting brackets for antennas that take a u-clamp like this one. https://www.mouser.com/ProductDetail/Seeed-Studio/318020691?qs=sGAEpiMZZMukHu%252BjC5l7YTkdPQ2v63pB7LKnWGhzBgE%3D Designed it to make a portable Meshtastic site.…
Automatic Milk Bone Dispenser Description: This project automatically pushes a single Milk Bone from a hopper. When powered on, the dispenser initializes by pulling the rack back for 2 seconds then releasing tension. When the arcade…
I wanted to create a mount for a moto-tag (airtag) that wasn't in the frame as the metal of the frame can block signal strength. I also didn't want to place it in the obvious under the seat places as well. I decided to place it on the…
After modification to the RC1N controller, I picked up these dualband antennas from Amazon: https://www.amazon.com/dp/B07YRSPRK6?ref=ppx_yo2ov_dt_b_fed_asin_title They are large and do not stand upright. I designed this print to snap over…
These are all currently available results.
