Counting matching models…
This allows adding a second 2.5 inch dust port onto my Rigid sander. This better matches the airflow requirements for my 4 inch dust collector. If you see my 4 inch PVC dust collector project I have a splitter to go from 4 inch to two 2.5…
Customized version of http://www.thingiverse.com/thing:2187167 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=2187167 Instructions Using the following options: enable_auto_pin_size = 1 resolution = 128…
I printed gears and mount in ABS and it seems to work fine. I printed a second set with the gears made from armadillo filament. Time will tell if there is any real world difference. Travel will cover a 4 inch blast gate and all three…
Adapter to plug a hose into the dewalt orbital sander. Don't buy the 'univeral' adapter from dewalt it doesn't work with this hose size. Why does everything have different dust ports ??? Category: Tools
MAKE SURE TO PRINT THE TEST OBJECTS INCLUDED FIRST. Test to make sure your bits fit in them the way you want. I made it fit snug on my printer so the bits don't fall out even turned upside down. You may need to scale up to get it to fit…
This fixes an issue I had where there was very little plastic between the inset nut holder and the outside of the model causing it to be weak. I also thickened the pieces attaching the cylinder to the main model by 1mm. I made the clip…
Customized version of https://www.thingiverse.com/thing:951308 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=951308 Instructions Using the following options: base = 0.7 magnets = 2 magnet_height = 3…
You would think that eventually someone would make two tools with the same size dust port by accident, but nope.. they are all different. Category: Tools
Long and short clip to clip together a layer of cork, glass, printer bed and PEI all together. The little tooth goes on the bottom side and digs into the cork. You may need to adjust thickness of the clip based on how thick your cork is.…
**Update - 2019-08-02 - Added another version without the guides since I use grooves mounted in my table to keep the wheels accurate and don't need them anymore. Also has bumpers for endstops to contact (see my other project for endstop…
Here is an enclosure I built for a 3d analog joystick to control marlin (In my case a lowrider CNC but should work for any marlin machine). You can find a discussion of the mod here:…
Some hold down clamps made for 3/8" bolts. The quick release works by simply sliding between the thin side and thick side under the bolt washer. The two clamps in the photos are the most useful but I have needed the others sometimes. You…
This is a pen holder that snaps into the dewalt router plate that is standard for the low rider V2. Just pull out the router (or retract it if you have a short pen) and snap in the disc from underneath. Compatible with my Z-Probe so it…
I didn't happen to have a prototyping shield board so I put together my project on a perma proto board I had lying around and made this case. Everything snaps together. Optional button lines up with a pushbutton mounted on the proto…
Original model scaled to 65% to fit my 15" 2016 MacBook Pro with Touchbar. Laptop fits with my case either way up but more snugly if you put the fat end down. Models also include some rubbery feet I printed in Ninjaflex (seen in grey in…
Update 2021-10-22 - Added fake nozzle for 1/4" mills Update 2019-09-17 - Added a fake nozzle that slips on my 1/8" fluted mills. I find it easier to pop on and off. I cobbled together a working bed probe for my low rider.. there are two…
This allows a 4 inch dust collector hose to be attached to a low rider 2. I had originally intended to drill a couple holes in the 'wings' and bolt some velcro strap on, but it seems to friction fit on the machine fine for me without the…
Low Rider Homing Sequence Video: https://youtu.be/DmiqzhqKCRY Updated 2019-06-17 - Added belt retainer with integrated endstop bumper, and matching endstop mount that screws onto outside of Y carriage. Added part for belt retainer to give…
I found the stock belt stops caused binding since the belts were not paralell. With a 1/4" gap from the table to the vertical pipe you want the 6 or 8mm clip.. put it on the belt like the photo Category: DIY
This clips on the vertical pipes and holds the low rider near maximum height even after the steppers are disabled. You can scale Z height to make it hold at any height you want. Category: DIY
After building a torsion box for my lowrider CNC router I discovered I didn't install enough threaded inserts for hold downs.. these are 3d printable ones threaded for 3/8" -16 bolts (I recommend nylon bolts if you can find them). These…
This fits over the 2mm end caps on the rolling pin to give you 3mm.. this is for the new design that doesn't have the flat discs and bolt but has the caps that slip on the end. Print Settings Rafts: No Supports: No Resolution: 0.2mm…
Update 2019-04-03: Had to reprint part in PC+ filament since PLA was warping. Added V3 version with tighter tolerances and more supports to prevent warping. Update 2019-04-01 : Added V2 version with a spot for the nut in the small piece…
I had issues when cutting circles.. they were squashed in the X direction since the belt didn't have enough tension. I found the tension hard to adjust with zip ties.. so I made this. Edit - Added version with 4mm bolt hole I think this…
Case for the moderndevice AC current sensor from here: https://moderndevice.com/current Just print, snap the board into the case and slide the lid in (use a drop of lube). Scale the height of the tab piece to tightly hold the cable.…
These are replacement arms for the BenQ 3d glasses that take the batteries (not the rechargeable ones). The original glasses seem to have a bad design where the arms break really easy. I included two versions.. one with pins like the…
You can just print the arm which is compatible with the Koss KSC75 and use it with the part this is remixed from. You can also try the clip included which I adjusted to fit my head (and the oculus band) better for me. Category: Toy & Game…
Replacement pad for bighorn fence clamps so they don't damage the aluminum fence on my table saw... they also extend farther in since my fence was below the minimum width. Makes the clamps able to clamp up to 1 inch smaller and makes the…
This is a case that lets you mount the new Viki panel on the front along with mounts inside for a Rambo 1.3 board and a raspberry pi with enough room left over for the wires. Ventilation is provided by the ATX fan. Includes spaces for…
All the acrylic parts seem to get brittle and break over time. Attached is a scale drawing of the Z plate the lead screw bushings are mounted on. Just print the PDF (make sure to set scale to 100%) then cut out, stick to some 3mm sheet…
This is a remixed version of the camera mount that fits the wider tabs on my aftermarket aluminum composite carriage. I also made it rise up a bit as I found the camera kind of low. You will also need the camera enclosure from the…
I printed this with ABS.. you may need some tweaking to get it to fit with other filaments. Category: 3D Printer Accessories
Vertical Mount for full Rambo board. Lid snaps on. Category: Electronics
Just print it and use two or three bolts to attach to your magnetic clip on accessory for this mount. It will push the endstop before the accessory crashes when homing to the right.
These are all currently available results.
