Counting matching models…
A kettlebell inspired keychain. Prints pretty good without supports. Hot tip: Pause the print while the handle is printing and put the keyring in place. Originally published in 2019: https://www.thingiverse.com/thing:3989772 Category:…
THIS IS THE OLD VERSION! Check out the improved version here: https://www.printables.com/model/584327-dollhouse-bathroom-set-v2 (Better 3D model integrity, visual improvements) -------- Scale is 1:12, you can scale up or down in you…
A modern style bathroom set for your dollhouse These are designed to be easily printed without supports, and with large enough bottom surfaces for good balance. Scale is 1:12, you can scale up or down in you slicer. For example, scale up…
A ball jointed printable tripod. This is a new version with the following updates: Now supports both landscape and portrait! Legs are slightly longer for better stability The tripod base is more streamlined with less sharp edges Improved…
This is an adjustable print-in-place spool for filament samples. No assembly needed, just remove from build plate, snap off the built-in supports and you're good to go. How to use: Adjust the arms inwards until you can fit the sample roll…
A ball jointed printable tripod. Check out the new version of this! https://www.printables.com/model/177685-phone-tripod-v2 Measure the width of your phone (or google for its specs), and select the closest size Phone Clamp. If you use a…
A simple wall mount for snowboards. Should fit most boards up to around 12 mm in thickness. Make sure to use a strong material and adjust your print settings for maximum strength. Don't use in a place where someone could get hurt if the…
Dual color diamond earrings. I used Polymaker PolyWood for the lower section and regular white PLA for the top surface. A variant with a sidewards facing fastening hole is also included, note that it has the same thickness as the rest of…
A floor stand for tower cases. Good for minimizing dust entering your computer and allowing for easier access. Computer maximum width: 17 cm (6.7"). Width on build plate: 23 cm Originally published in 2019:…
A handy strainer for pouring out the water after cooking pasta, rice or vegetables. Easy to just rinse after use, keep on a hook near the kitchen sink. It comes in three different sizes: a small version for pots up to a diameter of 18.7…
A rad radius gauge for measuring radii of around 40 mm and bigger. Use the free web app calculator to calculate the result, it's super easy! UPDATE 2: Added versions without the shelf in the hole. Now it should be able to take calipers…
Instructions: Drill a 20 mm hole through the wall Choose the "long" part according to the thickness of your wall Insert the "short" part on one side, and the long part on the other Fasten with a 3 mm wood screw that's long enough to reach…
A sleek stand that should fit most tablets. Tilt angle adjustable with screw. Prints without supports. Make sure you print it lying on its side, like it is in the file. The "Low edge" version is for minimizing screen obstruction on…
Finger Skateboard Quarter Pipe Ramp A nice quarter pipe with included storage for your decks and other accessories. Instructions: Any filament is OK really, no supports needed Optionally put in a color change at 110.2 mm if you want a…
Gingerbread Wine Glass Markers A set of 12 cozy wine charms to help your guests keep track of their glasses! If you need more than twelve, just print another set using different colors. Print using the Color Change feature of PrusaSlicer,…
A set of model kettlebells for dollhouse, Barbie etc. Prints without supports Smaller set (dollhouse): heights 16, 18, 20 and 22 mm (around 0.6 to 0.8 inches) Larger set (barbie): heights 24, 26, 28 and 30 mm (around 0.9 to 1.2 inches)…
A tilted platform to keep underneath your mouse pad. I find this much more comfortable for my wrist, and a cheaper option than buying an asymmetrical gaming mouse. Fits a mouse pads sized 20 x 25 cm, you can always cut an old mouse pad…
A sink for outdoor use. This is for a cabin that lacks running water. The plumbing consists of a manual-refill wall mounted bucket and some garden hose. Required build plate size 24 x 18 cm Drain hole with 1/2 inch BSP plumbing thread…
The Cynel spool is 66 mm in diameter, 20 mm center hole and 22 mm wide. Prints without supports. It has an M5 threaded hole through the spindle in case you want to reinforce it with a screw. EDIT: I didn't like the slot design, it was too…
An impact resistant case for Lenovo Tab A9 Use flexible filament only, won't fit if printed in hard plastic! Cut out the designed-in supports (see pic) after printing with a sharp knife. Easy to remove and re-attach when needed Perfect…
Screw tray for 8x3mm neodymium magnets. Magnets can be pushed in place after printing, and stay put nicely. They can also be removed if needed. The dimensions of the tray are 80 x 40 x 12 mm To install magnets: Push the magnet into the…
A stackable coaster to celebrate the successful launch of the JWST! - Comes in both stackable and plain versions (with and without knobs) - Comes in two sizes (max cup base 76 mm and 90 mm) - Print with color change at > 1 mm
A hook buckle replacing the ordinary side-release buckle clip on my messenger bag. The original one broke pretty easily, and has been replaced a few times. Also, I wanted a buckle that's easy to operate one-handed while riding a bike.…
Extendable Drink Cooler A threaded design that fits cans of most sizes. Engineered for insulation while still being slim and comfortable to use. Show your appreciation for Ukraine, Open Source Hardware, Linux (Tux), or the sun! Plain…
Attaches to barbells up to 29 mm and has two settings, 5 cm (2") and 7 cm (2.75"). Use 10 mm double sided velcro to attach. Inspired by mickeshobby 's design: https://www.thingiverse.com/thing:1642913 Originally published in 2019:…
Old purge lines and filament change leftovers always seem to end up under and around the printer. This is an attempt to solve that problem. Important : This part snaps to the M10 rods of the older (pre Mk3) frame. It is not compatible…
Printing and Assembly Instructions Print the bristle (5 copies) with TPU. Use the "thin" version for harder TPU and the "medium" for softer. I haven't made a thick version, as I don't think it will work with extremely flexible filament…
Print with high-flex TPU, I used ColorFabb VarioShore.
A chessboard sized 20x20 cm (roughly 8x8"), so it should be printable on a wide range of build plates. Print the chessboard base in one color, and 32 copies of the inner square in another. The inner square is 0.05 mm smaller than the…
A centered light holder for threadless (A-head) stems. Small print and an extremely simple attachment system. The holder is attached with a single piece of bungee cord that keeps both the light and the holder in place. The grooved version…
I wanted bindings with the newer model toe strap that goes over the toe cap instead of the old-school over the foot type. Have been using these for two winters now, haven't failed me yet! Printed in A95 shore TPU.
A table stand for Taranis X9D Plus. This stand has room for the USB cable when playing simulators. Easy to print without supports. Originally published in 2018: https://www.thingiverse.com/thing:2981532 Please post a Make if you make…
This thing completes the otherwise awesome Ascaso i-mini coffee grinder. I use some Blue Tack to keep it in place. Originally published in 2018: https://www.thingiverse.com/thing:2808554 Category: Kitchen & Dining
A nice led strip fixture for Prusa i3 Original MK2S._ Does not restrict extruder movement This lighting solutions uses a popular self adhesive 12V LED strip (see image). Can be installed to use the printer's own 12V supply. UPDATE…
The same idea as the inserts traditionally made of cork, the honeycomb pattern increases airflow. Put one or two of these under the sweatband of any hat of traditional design. Must be printed with a flexible material like TPU! Two sizes:…
A housing for ESP32 C3 with built-in OLED Perfect for projects like Temperature/hunidity sensors, or anything else with a small display Features Three variants, one with no buttons, one with both buttons, and one with only the…
Decorative snowflakes Ideal for decorating your printer, computer, walls, ceilings… Use blue-tack, hot glue, double sided tape or similar to attach Warnings and tips This is a difficult print! You need good bed adhesion and a well…
Quick design but works pretty well, some notes: Fits roughly 530 BBs, the smaller one fits 460. Works with 20 mm wide mags, and the distance between loading hole and mag base plate 20 mm. The pressure relief plate may help with shaking…
Features: Auto-latching - you won't have to remember to close it. Can be easily opened from both sides by adults and older kids (depending on install height). Very strong when printed in TPU using thick walls and dense infill (I recommend…
These are all currently available results.
