Counting matching models…
If you, like me, have a lot of cycling shoes, then you'll probably have a problem storing them all. With this in mind, I designed this little peg that you can screw into a wooden baton to allow you to store all your shoes. One peg per…
This is a case to house a pair of reading glasses. You can customise the end with your initials should you like - I have included the Fusion 360 file. Print instructions Unassociated tags: Glasses case, Reading Glasses Category: Household…
50mm castor wheel of the type used on the bottom of cabinets. Print instructions Unassociated tags: 50mm castor, castor wheel, swivel castor Category: DIY
This is a small magnetic hook to allow things to be hung on a fridge or magnetic board. To use, you'll need either 1 or 2 neodymium magnets (2mm x 10mm). It works fine with 1 magnet in the top position. Use superglue to fix. Print…
This is a cake topper in the shape of spiderman. You'll need a fairly large printer to print it, and a clean print bed with an even temperature as it has a tendency to lift on the corners.
My 1997 Scalextric Escort Cosworth's wheels were looking a bit tired and wer loose on the axle, so I designed these 8 spoke replacements. The standard slick tyre fits straight on. NOTE: They're a tight fit. Now my Gossie is back on the…
This is a small Christmas tree decoration shaped like a tree that could be stood up on it's own or hung on a tree by a string. Originally, this tree was designed to sell at my daughter's school Christmas market to raise funds for her…
This is a Lego Ninjago topper for a cake. You'll need a reasonable sized print bed, Prusa i3 is more than big enough.
This is a hybrid Voronoi Christmas Angel, designed to sit on top of an artificial Christmas tree or as a standalone ornament. As artificial trees have little stiffness at the top due to their wire frame, I designed this angel to be as…
This is a model of a NEMA17 stepper motor with a 40mm body. Also included is a right angled motor mount.
This is a box and lid for the Cards Against Humanity game. Inside there are two receptacles, one for the white and one for the black cards. The box is square so the lid can be put on in any orientation. This design can be printed in one…
This is a entirely 3d-printed hinge that I've designed to allow an 18mm MDF door to pivot adjacent to an 18mm panel. I used 4 x 4mm x 20mm screws and the model is sized for these. Apart from screws, no additional hardware is required.…
This is a design for 'pedestaling' the aerobars on a set of Ventus II tri-bars. They fit in between the basebar and the extension clamps and adds 50mm of rise. You need two of the risers (they're not handed), two of the tops (not handed…
This is a replacement bridge side for the Brio-compatible wooden railway set sold by the Early Learning Centre. The originals were made of flimsy thin ABS that weren't up to the destructive capabilities of a 3 year old. This version is…
I wanted a musical-themed cake topper for a birthday cake. After a lot of searching, I couldn't find one with a bass clef, so designed my own. Best printed on a large(ish) format print bed. Prusa i3 is enough.
This is a hook that you clip on to your mantlepiece to allow you to hang up a stocking at Christmas. It's sized to fit a 58mm shelf, but it's possible to reduce this either by adding a spacer or adjusting the FreeCAD file. There are three…
This is a fun-little tree that can either be hung on your big Christmas tree or be free-standing anywhere. The trunk is mainly octagonal in cross-section, but I've added an angel outline to give a bit of interest. It is made of 4 parts,…
This is a hook that fits on a shelf to allow things to be hung from it. This model is sized to fit a 15mm thick shelf and it fits snugly. I've added a second STL that moves the boom and stick down and round and the bucket under the…
I wanted a stand for my TV, which has a 200 x 100 VESA mount. I trawled the internet and couldn't find one that I liked so bought a surplus Dell stand and set about making an adaptor. The adaptor fits straight on to the Dell stand via 4 x…
83mm aerobridge to fit extensions of 3T Ventus 2 tribars in order to stop them moving under load. Holes are included to allow fitment of a cable-tie. Print instructions Unassociated tags: Aero bridge, Aero extensions How I Designed This…
My car is due a service so wanted to check how much tread depth I had. I couldn't find one that I liked, so made my own. I included a hole for a keyring.
This is a remix of the Kryolan makeup case by Delfini. It is sized to take a 44mm MAC Pro Palette Refill Pan and contains a pocket for a 10mm x 2mm Neodymium magnet. Print instructions Unassociated tags: Make up Category: Containers Print…
Even Lord Vader liked to have a bit of festive fun whilst scouring the universe for Rebel traitors and planets to destroy. Here's what his tree in his office might have looked like, with a couple of strormtroopers (see:…
This is a desk tidy, to put all the random stuff that accumulates during the day. Hybrid-Voronoi style, so un to watch it print.
This is a tool that holds a 4mm rod to allow accurate cutting at 20mm and 40mm. I successfully used it to cut 4mm carbon rod with a hacksaw. Use 3.5mm x 20mm(+) countersunk screws to hold it to a bench or piece of wood to allow cutting.…
This is a cutter and a pusher in the shape of a dog paw. You need to use the cutter to cut the icing, and then use the pusher to push it on to the cake.
This is a simple hook to allow you to unhook the chain catch from a window that is jammed. Useful in emergencies! Gcode is for a Mk3 Prusa.
This is a holder for a A3 whiteboard. It's designed to fit this exactly: https://www.amazon.co.uk/gp/product/B01AG0Y7OS There are two main legs, which are handed. Other plastic parts needed are two hexagonal and two shaped nuts. Finally,…
This is a heart-shaped hook to allow the hanging of items from a 12 to 13mm thick shelf. If it's not a tight fit, then a strip of paper may be placed in the 'jaw' to not only protect the shelf finish, but to take up any slack. I used ABS…
Inspired by other designs, I bought some Dunlop squash balls to fit to my 2040 Bear-framed i3. It turns out that the Dunlop balls are bigger in diameter than most so couldn't use existing designs. I also found that my frame isn't V-slot,…
Prusa Bear Z-axis top with filament hose holder extension. This is a remix of https://www.thingiverse.com/thing:2808408 to include a clamp / holder for a filament hose. Use a 3mm nut and 10mm cap head nut for the clamp.
These are all currently available results.
