Counting matching models…
Printable speaker grill for audio projects. Designed to fit Pride Diamond 8 V2, but they should fit many other speakers (tested also with Rockville RXM 84). I've printed mine with ABS so they won't deform under higher temperatures.
I needed some holders for 5s pack to repair my drill battery so i made this simple model. Inside diameter is 18.3mm (mine fit perfectly, but it was too small for some cell so you might need to scale it up a bit), height is 10mm but you…
Handle that can be printed without supports. Easy to sand and paint if needed. 97mm between holes Use at least 30% infill. 1:30h print time, 14g at 50% infill and 0.2mm layer height
This is 3D printed variant of https://www.instructables.com/Portable-Bluetooth-Speaker-Made-From-Scrap-Wood/. You can follow the same guide because enclosures are almost identical (i used same dimensions). Two holes on front side are for…
ANL Fuse holder blocks for one or multiple fuses with single input. One side of fuses is tied together. If you don't want inputs to be tied together, you can use negative volume in slicer and remove part that surrounds busbar and just use…
I have few devices that use 21700 batteries, but i only have one. I have ton of 18650 batteries with higher capacity so i thought about using them instead. There are two models, adapter and sleeve. If your device has longer spring (since…
This is variant of https://www.instructables.com/Portable-Bluetooth-Speaker-Made-From-Scrap-Wood/. You can follow the same guide, but instead of using battery and step up module you need step down module. This speaker is made with 5V…
I'm reusing old MGN12C rails for Z axis instead of MGN9H, Keemo already changed original models, but it's for MGN12H. Holes are spaced 15mm instead of 20mm on C carriages so I've added extra holes for those. Use "[a]_z_carriage_left" and…
Simple enclosure with holes for easy mounting. Print with something heat resistant, these can get hot when they are discharging batteries. There are two versions, one with honeycomb pattern and one that's fully closed.
Original backplate for the JCD 8898 soldering station. Printed with Ender 3, 0.3mm with supports and it fits perfectly.
Updated version of my door vent. You can put it on doors, printer enclosures, dehydrators, pretty much anywhere where you need airflow. Face is 1.5mm in height and 10mm offset, rear side is 15mm. Doors should be at least 30mm thick.…
Mount for Sofirn SP40 on 25.4mm handlebar (1 inch). Printed with PLA, 0.2mm layer height on Ender 3 Holes are for M3 nuts and bolts EDIT: Added shorter mount
Minimalistic speaker stand for small speakers (Audioengine A2, Kanto YU2). It was designed to use as little filament as possible without loosing stability. Use rubber pads on both sides to prevent speaker from moving. Printed with 10%…
Printable speaker ring for Deaf Bonce Apocalypse AP-T25 NEO tweeters. I've printed mine without bottom layers and after i filled it with resin. No issues so far. Print with PLA or ABS if you plan on using it with resin. Resin doesn't…
Holes on closet were 5mm in diameter and 12mm depth so i modeled these according to those dimensions. Printed them in ABS in orientation that they are modeled. They should be fine for static loads, don't use them for anything other than…
Just a simple enclosure with holes for easy mounting. Print with something heat resistant, these can get hot when they are discharging batteries. Honeycomb pattern for ventilation and LEDs.
Simple pressure fitted belt clip for Parkside PLEM 20 laser distance meter. I've printed mine with PETG, 100% infill and fuzzy skin to add some texture to it. It didn't fit at first so i had to heat it up a bit and slide it on.
M12 nut that i use on Yinlong LTO packs to isolate them. Don't overtighten it, it will crack due to layer orientation
These are all currently available results.
