Counting matching models…
My mom (and some of her friends) have trouble holding a full Bridge hand, 13 cards. This is a simple but effective tool for doing just that. Curved to keep cards private, sits nice and stable on table. Easy to print, no support needed.…
These strobe disks are for checking/adjusting the speed on your turntable, assuming it doesn't already have this feature. When using the applicable disk, viewed under fluorescent or other 50 or 60hz light (neon or similar) with your…
The Fuji X-T10, X-T20 and X-T30 are great little cameras, but the grip is a bit small for larger hands: your pinkie has no-where to go except under the camera. This newly updated grip provides full support for all of your fingers, yet…
This is designed specifically for the camera that Lightburn sells for use in Laser Engravers/Cutters. It mounts to the underside of the lid, pointing down at the bed. The swivel allows the camera to be adjusted for angle and then locked.…
This is a fully functional low profile wheel-style rotary axis for Laser Engravers/Cutters. There are a few purchased parts, but most of the interesting stuff is 3D printed. The motor is a standard NEMA17, I plug-replace my Y-Axis motor…
I like to do my own framing of printed photos, but the frames often lack a good mounting point. This 3D printed part adheres to the back of the frame. For lighter frames, I've been using high strength 3M mounting tape (3M Scotch Extreme…
The Fuji X-T3 is a great little camera, but lacks an Arca-Swiss mounting plate. Also, the grip is a tad small, would benefit from a bit more beef. This newly designed grip provides both features, yet doesn't block access to any of the…
Thanks to schindi77 for a great design. This saved me about $80 and works and feels wonderful. I am posting the stl and 3mf files for the wheel, my main contribution. I had to drill out the m2.5 holes a bit, not hard. The thumbwheel…
The Fuji FUJINON XF16-80mmF4 R OIS WR lens is a well regarded “kit” lens, known for being sharp and versatile. It normally comes with nice hood, but this often gets lost or damaged. I searched everywhere for a replacement and, other than…
This handy caddy solves a long-standing problem in our shower, too much stuff! I made two of them, see the photo. They are each adhered to the fiberglass wall with 4 pieces of high-strength 3m Automotive Tape. Enjoy, and let me know if…
This attractive case is designed to hold, cool and protect a variety of common controllers such as the MKS GEN L, MKS Gen 1.4, SKR 1.3 and possibly others. With easy access to connectors and micro SD card (SKR), this box has proved…
The Fuji X-H2 and H2S are great cameras. This new grip expansion provides full support for rapid mount Arca-Swiss tripods, yet doesn't block access to any camera features, such as battery, display etc. In case you DO want to use a…
Simple tool to aid in cutting accurate and repeatable spline grooves in the corners of picture frames. Print at 50% infill or more for greater strength. I used PLA but others will work. When using this jig I recommend using a clamp to…
This is designed to conveniently hold the 7-piece set of Bondhus balldriver Allen wrenches, my favorite tool. The size of each wrench is embossed on the side. Available through Amazon and others. Print at 50% fill or above, upside down.…
I have an extension pole with a standard threaded end, perfect for a roof rake. This is the actual rake part, ready for mounting onto a pole of any kind, as long it has the correct thread, the kind you'll find on a push-broom. It's kinda…
This simple stl file is provided as a quick way to confirm that your bed is level and properly zeroed all over, or that your autoleveling works as expected. If it is not the right size in any dimension, simply re-scale it in your slicer…
This spool holder is designed for the TAZ-6 printer, but will probably work on a variety of others. I have included the Solidworks source files for those who want to modify. To use this you make one Spool Holder and one Cap. Then cut a…
I bought a nice used Fuji X-T1 (XT-1) camera, it was missing the little plastic cover on the bottom of the camera that protects the electrical pins. These are used by a battery grip, if there is one. This is a simple part, clicks firmly…
As shown in one of the photos, the bracket for one end of our storm door closer rusted and broke. I replaced it with a work-alike 3d printed part. PLA, 80%, no support. Update: I have uploaded a new version, stronger. The first version…
This thimble is designed to help hand-sewing, used to push needles and protect the finger. It has ridges to catch the head of the needle/pin. Size it up/down as needed.
File this under "stupidly simple tools that solve a niche problem". I use the small Elmer's Glue-All to assemble my various laser-cut wood projects. Just like a ketchup bottle, the glue settles to the bottom, away from the nozzle. With…
Owners of the Precision Matthews PM25-MV Milling Machine quickly discover how difficult it is to change tools in the absence of a spindle lock for the R8 spindle. This simple 3d printed part solves that need by making it easy to…
This miter slide is inspired by a product made by Rockler, and by a similar design by Neil Ramsay (https://www.printables.com/model/452577-45-degree-miter-sled). This is NON-COMMERCIAL, make for yourself or a friend only. A few notes…
If you own a Laser cutter/engraver you owe it to yourself to monitor the current to the tube and keep it within manufacturer-provided safe operating limits. Failure to do so will cause early death of the VERY expensive tube. For some…
This little tool has been a help when I don't have enough “dogs” for my woodworking bench. Be sure to print on its side (for strength). In practice this has been plenty strong for clamping about anything. Best to use 50% fill or higher.
This is a DIY lens hood and cap for the very capable TTArtisan 27mm F2.8 lens. This has been tested on my Fuji X-T5, no vignetting has been detected. It is friction mount, grabs onto the periphery of the little lens hood that comes with…
This is a Z-Axis way cover for the Precision Matthews PM25-MV milling machine. Instead of the factory-original bellows type (which takes up about an inch of precious y-axis motion) this takes up essentially no room and works flawlessly.…
I have a riding mower, a Greenworks 42 Inch Zero Turn Electric. The hose attachment is fairly useless for cleaning the underside from grass and debris. I saw a product that is essentially a spinning sprinkler that you can slide under the…
This Fuji X-Mount “lens” is just for fun. Using your 3d printer you create what acts like thousands of little light-pipes projecting a nearby object's image directly onto your camera sensor. Not intended as a real lens – no focus, no…
For fans of the old "Skibble" game, here's a 3d printable puck or "shooter". Enjoy! Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.16 Infill: 80% Filament: Any PLA Any Notes: This is an…
These two cases are part of my newly developed DASH printer (design soon to be uploaded). I use the MKS 1.4 controller due to its nice integration and support for 24v operation. This is the full size board, NOT the "base" version. The LCD…
This bracket and firmware provides support for the BLTouch in the Lulzbot Workhorse 3D printer when used with the ITWorks print head: https://itworks3d.com/product/e3d-titan-aero-pro-toolhead-for-mini-2-taz-workhorse/ Edited source files…
Each late spring the little sugar ants invade our kitchen, searching for little bits of food scraps. To them a crumb of food looks like a feast for hundreds. Once they find food, they leave scent trails and before you know it there are…
Important note: This project is fairly out of date now. The Taz 6 is no longer being sold, the BLTouch is at version 3 (not compatible with firmware for version 2), and Marlin itself has moved way beyond this version. If you want to view…
Here are two versions of the same lens hood, one with a magnetic cap, the other with a snap-action cap. These have been tested on both the Fujifilm 35mm F2.0 and the Fujifilm 23mm F2.0 lenses. No vignetting has been detected. They are…
These stiffeners may be used liberally around the frame of a 3d printer or other CNC device, they help to reduce flexing. The sizing is appropriate for OpenBuilds-style extrusions, with M5 hardware and t-nuts.
I drive a 2013 Subaru with an automatic dimming mirror. Most of the time it's great, but there have been a number of instances where I want it to dim but it just won't. There's no manual over-ride. This usually happens at dawn or dusk.…
This AnyCubic Linear Plus mod is in response to the very poor operational properties of the supplied linear glide rails that they provide. I have replaced the vertical member with true V-Rail from Openbuilds.com, and used the wheels and…
Trav-A-Dial bracket for PM1228LB-VF lathe, Solidworks file available on request. Two machine nuts are inserted in the grooves, one for tightening the dovetail (I used a thumb screw) and one for pushing the Trav-A-Dial forward to engage…
These .3mf files are for temporary use by those interested in the XRP robot, soon to be replaced by the more complete Open Stem Initiative site. I will pull this down when the “real thing” is available.
I recently purchased the Logan 450-1 Mat Cutter, and generally speaking it's really great. However they apparently decided (for marketing reasons?) to reduce its convenience, providing only a small and poorly placed edge guide. This makes…
Here's a lens hood for that Viltrox 9 or 14 mm Air Lens. This is a simple part to make, and serves a useful purpose. I've not noticed any vignetting due to the petal design. Bayonet mount, place it on the lens and turn about 1/4 turn to…
These are all currently available results.
