Counting matching models…
Insert box for 400x300 Eurobox. Stackable for 2 layers of 4 insert boxes in a 220mm height Eurobox. Can be combined with other, larger insert boxes. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: No…
Inlay for the lid of the Wera Tool Check Plus Rugged Box that holds a Knipex Cobra Water Pump Pliers (87 03 125) and a Knipex Mini-Pliers Wrench (86 03 125), the 152mm bit holder of the Tool Rebels Edition of the Tool Check Plus and 8…
I enlarged the design from @moononournation to 30 rows and added dovetail slots to connect the Vcc and GND rails from a standard 400 pin breadboard. Category: Electronics
Modified mounting hole pattern to match a 43.4 x 23.3 mm version of the XL6009 DC/DC converter board. See pictures for dimensions of the converter board this was made for. Category: Electronics
The blow mold box that Mitutoyo Digital Calipers ship in has no space to store the paperwork for the caliper out of harms way. This rugged box has a space for the paperwork under a removable tray that holds the caliper and optionally…
This is a key to open the battery compartment of a Mares Icon HD scuba diving computer. If you need to replace the Li-Po battery of your Mares Icon HD, this tool will help you to open the battery compartment screw without scratching it.…
Clip to attach scuba regulator, octopus or finimeter hoses to a bolt snap.
Abdeckkappe und Standfuss für einen Stand-Ventilator. Category: Replacement Parts
Rack mount for a UniFi USW-16-Lite-POE switch that integrates in the modular 1U rack mount system. Due to the width of the USW-16-Lite-POE, I had to merge the middle section of the modular 1U rack mount system into the switch mount and…
Modified versions for mounting the Brennenstuhl ST BM 0619 Secure-Tec power strip under a tabletop.flush with the outside of the tabletop. Only works for Secure-Tec power strips, not for Eco Line. Category: Organization
After using the 6 partition divider ( https://www.thingiverse.com/thing:3366249 ) and the 9 partition divider ( https://www.thingiverse.com/thing:2562803 ) successfully for a while, I had the need to divide some of the drawers of my Aldi…
This is a remix of the low profile version of https://www.thingiverse.com/thing:2153437 by @bobtidey. I created a cap for the power button, extended the lid 1mm to center it better over the I/O pins and added a little hole over the reset…
Blank section for the 1U modular rack mount - in case you only need one switch. Can be used as a left or right section. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: No Resolution: 0.2 mm Infill: 25%…
Divider to partition the drawers of an Aldi / Allit VarioPlus Hobby 33 lengthwise. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: No Resolution: 0.2 mm Infill: 100% Filament: DasFilament PLA Black…
Remix of https://www.thingiverse.com/thing:1747635 for mounting on System 32 shelf pin hole rows (5mm holes at 32mm distance) as used in a lot of commercial furniture (e.g. IKEA). Category: Organization
I really liked the snug fit of @ethanca's original design but had two SYB-46 type 270-hole breadboards laying around here that I also wanted to use, so I modified the design for this type of breadboard. Print Settings Printer Brand:…
This is a spool holder base for the Ultimaker 2 and similar printers that can be used to mount the Creality Digital Spool holder.
Based on Part1 from https://www.thingiverse.com/thing:2268079 I created this version that can be used for smaller 5cc flux syringes. Use Part1 from the original and then use Part2b from here and a M3x10mm countersunk bolt and a M3 nut to…
Print with 0.16 mm layer height or better.
Halter für eine 3-fach Steckdosenleiste Brennenstuhl Eco-Line ohne Schalter. Die Halterung kann mit Senkkopfschrauben 3,5mm entweder auf einer waagrechten oder einer senkrechten Fläche befestigt werden. Ich habe je eine Version mit…
Modified version of the front cover for mounting a HDMI panel mount extension cable. The mounting holes of the HDMI panel mount are M3 and are 29mm apart. I used the left angled version from here:…
Box for an Adjustable Tap Wrench (176mm length), die stock for 20x5mm dies (186mm length), two 20x5mm dies and six taps (max. 55mm length). The bottom has holes for 6x3mm neodymium magnets and the lid has spaces to embed M3 washers as…
This adapter allows the use of one (protected) 18650 cell instead of 2 C-cells.
This front panel for the SCM SCR335 USB smart card reader fits in standard 5.25" PC slots. The smart card reader is mounted using the original case screw holes of the reader and two self-tapping screws DIN7982, 2,2 x 8mm counter sunk.…
Mount for the Banana Pi M1 with an additional 2,5" hard disk or SSD in a modular system 1u frame for 19" racks. It is designed to be on the left side. Use the middle and right section from https://www.thingiverse.com/thing:3690500 or any…
I store my Flipper Zero with the accessories in a zipper carrying case. As the case is plain black and easily gets mixed up with other similar cases, I wanted to mark the case with a badge.
Mount for the Banana Pi M1 with an additional 2,5" hard disk or SSD in a modular system 2u frame for 19" racks. USB and ethernet ports are accessible from the front via adapter cables. The front plate has built in button caps for the…
This mounting bracket can be used to mount a Mean Well ELP-75-5-C 75 Watt power supply in one slot of the 2U rack mount system described by Krapozok ( https://www.thingiverse.com/thing:1793758 ). The ELP-75-5-C is the same as the ELP-75-5…
Masterspool Adapter for BambuLab Reusable Spools with cutout for RFID tag.
Remix for an Edimax ES5500M 5-port Gigabit switch. The ES5500M has an odd plastic case and a power connector on the front. This mount is designed to replace the original plastic case completely. You can still power it from the front or…
I modified the top part of the C2C CaberQU USB-C cable tester case to work with the CaberQU A2C cable tester. The bottom part is the same as in https://www.thingiverse.com/thing:5568364 Print Settings Rafts: No Supports: Yes Resolution:…
I needed a version for five nozzles, so I changed @elmo2k3's nice design to this size. Since the overall width was very close to the width of the hot air station, I added two mounting brackets that are screwed to the nozzle holder with…
Remix of @tkramm's Rack Mount Adapter to fit a BeagleBone Black board. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: Doesn't Matter Supports: No Resolution: 0.2 mm Infill: 20% Filament: DasFilament PETG Black…
I bought a five pieces set of extra long drill bits. As they arrived in a zip lock bag, I created this nice and sturdy storage box for them.
This remix of the center box cover of https://www.thingiverse.com/thing:4377361 doesn't need any mounting hardware and can easily be removed without having to detach the left and right sections first. The door uses two printed…
I remixed this from https://www.thingiverse.com/thing:2851315 to get a shorter, more rounded version. The indentation at the back is sized for a TESA Powerstrip (Small). Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts:…
Print with TPU and use double sided adhesive tape to mount the feet.
I store my Flipper Zero with the accessories in a zipper carrying case. As the case is plain black and easily gets mixed up with other similar cases, I wanted to mark the case with a badge. Print Settings Printer Brand: Bambu Lab Printer:…
Power switch unit that fits the 19" 2U modular rack mount system. It provides 8 power switches. I used round 12mm self locking/latching push button switches like these:…
I wanted a nice, lightweight and easy to print cover for the Micro Mesh sanding pad holder from @peteryip ( https://www.thingiverse.com/thing:3754909 ) that is not completely closed so that the pads can dry properly but don't fall out of…
Alternative versions of the front USB panel with left or right ports blocked. These panels can be used to ensure that the ports are blocked if the corresponding internal USB header is used.
Print with multi color or a filament color change between layer 10 and 11. Fix with double sided tape to the L-BOXX.
I liked the look of https://www.thingiverse.com/thing:3027565 but wanted a few extra features so I created this version which includes holes for three panel-mounted 4mm safety sockets and a 3.5 mm mono jack. The tree 4mm sockets are…
Holder for three shot glasses (52mm diameter, 70mm height) Category: Organization
This is a snap-fit case for the HomeMatic WLAN Gateway developed by user amunra in the FHEM forum. For details see the forum thread: https://forum.fhem.de/index.php/topic,62651.0.html Print Settings Printer Brand: Ultimaker Printer:…
Modified version of Chucks nail and screw rack ( https://www.thingiverse.com/thing:2434113 ) that saves approx. 15% printing time. Category: Organization
Rubber Foot for HP Elitebook 8460P 8470P 2560P 2570P 2170P Print Settings Printer Brand: Bambulabs Printer: Bambu X1C **Rafts:** No Supports: No **Resolution:** 0.2 mm Filament: Bambu Lab TPU TPU-95A Black Notes: Print with TPU and mount…
Remix with rounded corners and German Text Category: 3D Printer Accessories
This plate stabilizes a DIN A5 (23x17cm) mesh bag and allows it to be screwed to the lid of a L-BOXX Classic. To mount it, use the plate to mark the screw hole location on the mesh bag. Then punch screw holes into the mesh bag with a hole…
Organizer für die Spielkarten und das übrige Zubehör für das Brettspiel "Talisman" in der 2. Ausgabe (von Schmidt Spiele). Die Boxen erlauben es, das Spielmaterial des Grundspiels und der beiden Erweiterungen Talisman II (Katakomben) und…
These are all currently available results.
