Counting matching models…
The orange Gyro 7 in the pictures is printed in 0.20mm layer height Printing Material: PETG (PLA makes the joints too loose when using the normal skeleton and too tight for the tight Skeleton . Assembly is also more difficult in PLA.)…
Print approx. €1.63–€1.99 excl. taxPreliminary estimate for PETGSource material: PET
the dispenser itself holds 7 cups with the short extension it holds 10. A dispenser with 2 normal extensions it can hold 20 cups. But you can shuffle it deepening on your needs 2 different cups can also be put in the same "lane" so you…
Print approx. €1.60–€1.96 excl. taxPreliminary estimate for PETGSource material: PET
I added lego motor on the side for the animaton, it was designed to be hand driven Printing all parts are already orientated correctly. Material: PETG the last letter on the model names indicate what color i used. Orange parts: 10% cubic…
A scan of my hand that's modified. There are also a six holes to mount it to a wall using a flat head screw or equivalent. (Don't use all screws at once they're there to mount it in one of 6 directions.) Printing the included .3mf file…
When trying to repair joy-cons I as do many people, striped one or more Y-screws and had to damage the shell remove the screw and repair the joy-con. So I needed a new shell but why buy something small and made of plastic when you have a…
Suet balls normally come in green nets that are not great for the environment The lid has holes to hang it from a rope or chain. When it needs to be refilled it can be unscrewed and filled. Printing I recommend to print the 3 parts…
The lid has two latches on the top to keep the lid from bending outward. The cards keep the lid closed. I have been using it daily sinds July 2023. I tend to not leave my home with coins in the compartment because it rattles a lot, but it…
layer height: 0.20mm or lower. material : tested with PLA and PETG. requires 10mm bridging and decent bed adhesion.
Printing Material: PETG for a more reliable snap latch and its better for outdoor use. Seam: exclude the seam away from the front, looks better. Assembly Its uses a filament hinge that can be pressed in and use Flush wire cutters to cut…
Print the “Engine block” at 0.3mm, if printing lower make sure the bearing is not connected to itself (right click model/Split/To objects) the “Finger Drive” can be used to hold the engine at a displaying angle (see second picture) the…
A bowtie 128.8mm wide 51.47mm high with two gears and a spring that connects them. the spring has a ∅ 10 mm hole to hold onto a button. In case you want a different size; use the bow tie without spring and bow tie spring models import…
It has a little give juist like the real chair! not as comfy though… Also check out Elitail version. Printing Material PLA Nozzle 0.4 (basic) Generate support On Overhand threshold 35º Support Style Organic Support on build plate only On…
Printing infill: 15% 3D honeycomb Material: PLA Layer height :0.2mm top fill pattern :Concentric (purely esthetic) Assembly the gray piece should be glued in place with super glue after making sure it can fit close to a 90° angle. Also…
I got the idea after printing this . I modeled new linkages to make it lighter. Fully assembled it weighs about 80g (depending on length). Requirements A ∅3mm x 1m rope 3*8mm round magnets (at least 12, add 3 for every additional printed…
The waffle pattern is the same as the original Printing I used: Material: PETG Box 0.30mm DRAFT profile modified with Vertical shells - perimeter: 1 Horizontal shells - Solid layers top: 3 Infill - Fill density: 10% The waffle 0.20mm…
Printing Layer Height 0.20mm or lower No supports needed Material: TPU and PLA (I used a mat PLA but most types should work) Perimeters: The TPU part 4 or more others can be juist 2 Assembly/Installation begin by pushing in the TPU part…
Heads up The black parts are big, (over 90big). I put hols in de model the combat warping. However it might slightly warp after printing souldn't be a big problem The white boxes can be arranged however you want, or you can design your…
The spacing of the pegboard was similar so it worked out pretty well. There are 4 sizes in case you want to cover the entire case.
the knobs have a M4 thread. if printed in one piece with a color print, it might be possible to glue it on something. But i would recommend using a M4 bolt. Printing layer height 0.20mm infill 20% grid perimeters 3 The Wrench G-code is a…
-Assembly- The links can be pushed in the middle of a tray but it is easier to slide them on. The end pieces are mostly useful when you arrange the trays in a way that leaves it open on one side. It may be a bit “floppy” when picked up…
This is a corsair AIO cap with a Moiré Illusion. powered by the PWM meant for pc case fans, meaning you can control the speed just like a pc fan in your bios, your motherboard's software or with iCUE. I made this for the Corsair Titan AIO…
Printing Material : PETG (PLA will work too but snapfit features may wear quicker) Layer height : 0.20mm is fine Bed adhesion : you need decent adhesion capability like with most 3D printable fabrics All other settings can be the default.…
This is a arm for a Magsafe charger or a stand which can be moved and held in a wide variety of positions. It can be mounted right side up or upside down. The clamp is 50mm so should be able to mount to most furniture -When changing the…
These are all currently available results.
