Counting matching models…
Print with ABS or PETG with brim and without support. Cut bowden properly at 90 degrees and insert fully (15mm, using a rag and some force; the bowden inputs are slightly conical). It will hold very well. If you have problems, you could…
Print with ABS or PETG with brim and support (only touching print bed). You need to rotate the model so that the single entry is at the bottom. After printing, remove the support by pushing filament through one of the opposite entries.…
Introducing a newly designed filament rewinder with virtually endless expansion possibilities . Main Features: Modular design for easy customization Sturdy and compact construction Minimal extra parts required: 7 × 608 bearings, 2 × 3 mm…
There are 2 gaps at the bottom of the printer housing (see picture). Filament particles may fall into these gaps and cannot easily be removed. This cover remedies the situation.
Print in light gray or silver PLA (e.g. Apple Aluminum Silver; I used FIL-ALFA GRIGIO METALLIC).
Print with ABS or PETG. Use auto rotation, no support. Don't use too much force when screwing in the PC4-M6's. Screw the small part to the printer (see picture), remove existing screw first. Remove the coupler from the printer. Screw in…
Yes, you can print on glass with the Bambu Lab X1! You need to tweak the start code in the slicer a little bit, because there is no special mouth cleaning area. Reduce the y values over 260 to over 250 in the === wipe mouth === section. I…
Print in ABS using brim and no support. Use automatic rotation beforehand. Carefully remove the four-wire cable shell, cut the red wire and attach an additional cable going to the filament run-out sensor switch to the NC pin and C pin…
This is an add-on for the Versatile Filament Rewinder. Print using the default slicer settings, ideally in PETG for durability. https://www.printables.com/model/1414113-versatile-filament-rewinder
Print with ABS or PETG with brim and no support (only touching print bed). You need to rotate the model so that the single entry is at the bottom. Don't use too much force when screwing in the PC4-M6's. Fully push the bowden tubes through…
Add-on to Versatile Filament rewinder. Print using default settings, preferably in PETG. Use normal supports for gear and ratchet part. https://www.printables.com/model/1414113-versatile-filament-rewinder
Easy to print and attach chute cover for Bambu Lab H2D.
This add-on to the Versatile Filament Rewinder powers the filament respooling. Print preferably in PETG with default settings. Use normal supports for gear and ratchet. I bought the motor/controller/power supply set from AliExpress (see…
This is a plug-in feeder for the Versatile Filament Rewinder. It is designed for 45mm spool widths, but should work for 50mm spools as well. I suggest to print it in PETG. Support is only needed for the case. Please note that the gears…
This is an add-on for the Versatile Filament Rewinder. Print using the default slicer settings, ideally in PETG for durability. You need 2 608 bearings. https://www.printables.com/model/1414113-versatile-filament-rewinder
This add-on is designed for the Versatile Filament Rewinder. It is installed in front of the donor spool holder to improve filament flow and add controlled resistance to the rewinder, resulting in more consistent layering on the receiving…
The auxiliary fan of the Bambu Lab X1 3D printer is glued to the side wall. On arrival of the printer, the fan was loose. So, I decided to design a fan holder to be screwed to the bar where the LED is attached. When installed, the fan…
This is an alternative axle for the donor spool holder for the Versatile Filament Rewinder. It improves filament rewinding by adding some resistance on the donor spool holder.…
These are all currently available results.
