Counting matching models…
This is an update of my original model Brush holder od autora Many24 | Stáhnou STL model zdarma | Printables.com It keeps the same simple and minimalist design, and adds double the slots for the brushes. Print instructions Printed in PLA,…
UPDATE 29/02/2024 Some people requested bigger chamfer on the mount holes to accommodate bigger screw heads. Original 2mm chamfer Updated 3mm chamfer UPDATE 31/01/2024 After first feedback it seems that the original tolerance 0,05mm is…
Update: You can check new version with more slots: Brush holder 6 slots od autora Many24 | Stáhnou STL model zdarma | Printables.com I was looking for very simple holder for just a few brushes, but none of them fit my needs, so I made my…
Cookie cutter for Christmas gingerbreads. Snowflake is raised by 4-5mm depending on your scaling to be “printed” on top of the glove. Update 11/12/2022 I uploaded another model with slightly increased height of the snowflake. Use…
UPDATE 16/02/2024 For anyone wanting to use threaded inserts instead of nuts, I created version 2.0 ___________________________________________________________________________________________________________ I liked the idea of swiss key…
Simple 2 piece holder for up to 8 wrenches, in my case for 6 - 22mm. There are 2 models, each with different hook position - offset by 20mm. This means you can put them in any column of holes on the Skadis board, depending on lenght of…
Simple 2 piece holder for hex key set, specifically made for Wera set but probably can be used with many others. This design works with 2 hooks, which is easy to install and remove, but holds very well thanks to the small bumps on the…
Hooks which I designed from scratch, inspired by “Pavel”. The original hooks didn't work as planned, they were too tight and the “one hook, one pin” design is not good, I also damaged the board in several places when removing the original…
This design works with 2 hooks, which is easy to install and remove, but holds very well thanks to the small bumps on the hooks: Print instructions I used PLA, but any material should do No supports needed 4+ perimeters for added stiffness
Remix of the great Talon knife by Hall Precision.
This is a very simple garden gate latch, easy to print, easy to install. To assembly it, you will just need hardware mentioned below. I recommend using locking glue to secure the bolt and nut over time, and to grease the “bearing”: Print…
There was no monitor stand that would match to what i wanted so I designed it myself. It's very simple yet modern design. Prints quickly and can hold quite a lot of weight. I tested it with approx. 5kg monitor with zero issues. It can be…
My previous version ( v1.0 ) of key hoder was alright, but had some design flaws and mainly, since then, I discovered the allmighty threaded inserts. So the goal was clear - make the model from scratch, more design consistent and get rid…
I really liked the idea of CouchConsole organizer, but wanted to put my Prusa Mini in use, so I designed 3D printable version. 2 sizes depending on your printer / preference: Prusa Mini: 180mm (max bed size) - I used this model Prusa i3…
Knob designed with attention to the best possible grip comfort. Turn the knob by 45°, depending on your prefered grip position. Hole for screw with included M4 thread. Print instructions I used PLA, but any material will do No supports…
I was looking for a way to hang my drill under a table, but all the available models were mounted in all kind of ways except the one I needed. So I made this holder, printed it in some transparent purple leftover PLA filament I had lying…
Pořadač na všechny mince kromě největší 50Kč. Používám ho v práci na drobné do automatu.
Collection of all parts needed to make a drybox out of the famous IKEA SAMLA This collection contains: Pneumatic air fitting holder Magnetic box for silica gel PTFE tube plug Cover clips - made by Wookbert PVC pipe mount with outside…
A funnel which you can permanently screw on a 5l canister. Funnel also have a lid so you never have to put original lid back. I tested 3 types of canisters and it fits perfectly. I use it for used frying oil, but can be used for many…
I made this hook to hang towels in bathroom, which didn't have the loop. Previous version was simpler, but didn't survive my GF's “power hanging”, so I modified it for improved holding strenght and durability. Print instructions Printed…
Matches which I kept in the garden close to a fire place had the boxes un-glued (probably due to humidity) all the time and were making match-mess all over the box I kept them in. So I made a similar size box which will hopefully last…
Had a 6 small dices laying freely around so I made a small box to store them. Print instructions The 2 halves of case are identical, each have 2 magnets. I used 5x2,5mm magnets and the holes are just tight enough to press them in with…
Keep your space organized and environmentally friendly with this battery bin! Designed to help you safely store used batteries before recycling. Opening of the cover is sized to fit even 9V battery confortably. Standard AA, AAA, button…
I could not find a well working stand, that was simple enough, would fit the charger properly and would not damage the charger when removing, so I made my own. It has very simple design, which requires a very little material, and has a…
This box was specificaly designed for Parkside PSB 6 A Forstner drill bits, but any similar size will fit. Size of bits is 15mm - 35mm. 4-point smart Quick lock mechanism ensures super fast closing of the box and secure fit. Print…
You should eat roughly 30g of nuts every day. This little bowl will give you just that, so you don't have to measure anything. Of course it will depend on many factors (size, humidity,..), but here are some examples: Pecan Walnut Cashew…
Just wanted to better organize all the types of tapes I have, so I made simple elbow for small shelf. Print instructions Can be use for many purposes, I used it with 16mm (inner diameter of elbow) wooden sticks and made small 2-tier…
I didn't want to glue a metallic disc to back of my new Pixel 6 to use it with magnetic holder in car, so I made holder which have the disc on the back, and the phone just slides in. There are 2 files: To be used with naked phone…
I wanted some simple holder for the 4 things I use the most. First version broke after some time due to weak spots, so this version is heavily reinforced to last for a long time. Print instructions Printed in PLA, but any material should…
I didn't like the original tiny handle which make the carrying of the heater nerly impossible single handed, so I made this simple handle which clicks in place a does not require any modifications to the heater itself so you don't loose…
These are all currently available results.
