P
PrintablesJay Nimbus
Intel NUC Wallmount/Under Desk Full Harness Version
A variation or original minimal design.
Print approx. €1.27–€1.55 excl. taxPreliminary estimate for one variant
- Downloads
- 149
- Likes
- 11
- Rating
- 5
All models
Counting matching models…
P
PrintablesJay Nimbus
Intel NUC Wallmount/Under Desk Mount Micro
Gcode included for PLA 0.4mm. If you print correct way up no supports needed.
Print approx. €0.25–€0.31 excl. taxPreliminary estimate for one variant
- Downloads
- 79
- Likes
- 8
- Rating
- 0
P
PrintablesJay Nimbus
Intel NUC Wallmount M3 Screws
Grab yourself a couple of 6-10mm M3 Screws that fit into the bottom side of the NUC. Mount the bracket on the wall and just slot in the NUC.
- Downloads
- 287
- Likes
- 33
- Rating
- 5
P
PrintablesJay Nimbus
Inside Y-Endstop Zero G Mercury One
Move the end-stop to the inside of the frame
- Downloads
- 247
- Likes
- 55
- Rating
- 5
P
PrintablesJay Nimbus
Ender 3 Flexi Riser Feet
I tried a few other designs but none hit the spot for me. This is inspired by many others, but as minimal as I can get it. To my horror, I found the left and right side extrusion of my Ender 3v2 is dimensionally different, so these were…
- Downloads
- 144
- Likes
- 28
- Rating
- 0
P
PrintablesJay Nimbus
Inside Y-Endstop Zero G Mercury One - no brace version
Can use if no corner brace is fitted so Y axis can go all the way back.
- Downloads
- 114
- Likes
- 20
- Rating
- 5
P
PrintablesJay Nimbus
Xiaomi Mi Outdoor Camera Mounting base
For mounting on weather board. The bracket included with the camera is hopeless. This allows 45% mounting angle.
- Downloads
- 103
- Likes
- 4
- Rating
- 4.5
P
PrintablesJay Nimbus
Ender 5 ZeroG Mercury One Dual-Z
Basically, all you will need is a second matching lead screw, motor, mount and coupler. I recommend buying two leadscrews together, as I had a hard time finding one that matched the ender 5 leadscrew. I had several ideas to replace the…
- Downloads
- 94
- Likes
- 33
- Rating
- 5
P
PrintablesJay Nimbus
Tension Plate for lowered cross bar Zero G Mercury One
Two M5 bolts fasten the 2020 frame to the 2040, with a third M5x8 and an M5 roll-in T-Nut. I had to tap a thread in the 2020 extrusion center.
- Downloads
- 82
- Likes
- 24
- Rating
- 0
P
PrintablesJay Nimbus
Gear Knob (Mazda BT50)
Printed with PETG due to in-car use. Seems to work fine. USE FUZZY SKIN mode to get nice grip texture. Use adaptive layers to get nice smooth top contour. Standard supports used. The screw sometimes comes a little loose, so I'd recommend…
- Downloads
- 68
- Likes
- 4
- Rating
- 0
P
PrintablesJay Nimbus
Stepper Tower Alignment Block Zero G Mercury One
Fit the block to the back of the 2020 extrusion with an M5 bolt. You'll have to tap a thread into it first. A little nub on top will snug into the standard stepper tower and hold it in place while you bolt it down resulting in proper…
- Downloads
- 56
- Likes
- 20
- Rating
- 0
P
PrintablesJay Nimbus
Ender 3V2 Y Endstop Enclosure
I couldn't find a drawing of this. All the available models missed it out and had no detail. It will fit the factory motor housing.
- Downloads
- 46
- Likes
- 3
- Rating
- 0
P
PrintablesJay Nimbus
Belt Silencer Zero G Mercury One
I found during input shaping the belts would vibrate which ruins the results. The side and rear belt runs are long. By adding some idlers you can raise the resonance and avoid bad ADXL measurements. 1. For the side belts: I added an idler…
- Downloads
- 42
- Likes
- 9
- Rating
- 0
P
PrintablesJay Nimbus
Ender 3v2 PSU Power Cover 50mm
So… I accidently got a PSU that was this THICC boy, 50MM thick (instead of 30mm). This mod was required to cover the electrical connections. You will need to fit 15mm - 20mm risers to your feet for ventilation clearance.
- Downloads
- 27
- Likes
- 4
- Rating
- 0
P
PrintablesJay Nimbus
Samsung TV Q60R Universal soundbar adapter mount
This adapter goes in place of the factory supplied stand/feet for the TV. In my case I wanted to mount the soundbar under the TV and the hardware I had wasn't optimal. Remove the feet and bolt on these adapters. There are M8 mounting…
- Downloads
- 18
- Likes
- 4
- Rating
- 0
P
PrintablesJay Nimbus
DIN Mount Breaker Enclosure Single or Double
I had trouble finding a suitable basic single enclosure for surface mounting a smart breaker. I made this one to fit the common breakers on aliexpress. The DIN rail is a printed part of the base so no need to mess around cutting a din…
- Downloads
- 15
- Likes
- 1
- Rating
- 0
P
PrintablesJay Nimbus
Ender 3 Toothed Pulley Belt tensioner 2GT X axis
I had a few goes at making a custom tensioner and accidentally arrived at one that matched the original style nicely. This allows the use of a toothed pulley that I think makes for less transmission of belt artifacts into the skin layers.…
- Downloads
- 13
- Likes
- 3
- Rating
- 0
These are all currently available results.