Counting matching models…
This is a modification of thing "Rattlesnake Rattle" by trishabelly thing 70991. I had a bunch of problems printing the original because some of the parts were floating above the bed. Split is the original cut in half and the two parts…
I got tired of loose line. This simple F360 design has parameters for spool inner diameter and height so you can print to fit whatever size you have. I use retainer width of 0.6mm for 0.3 print layer and print in vase mode so it's really…
The ramrod on my muzzleloader recently went missing. This is an easy replacement with a printed 1/2" - 13 threaded hole. Category: Sport & Outdoors
These parts are used to implement a spindle encoder on a 9x20 lathe using an Omron e6b2 encoder. This is useful if you are using a CNC conversion of the lathe. The LatheSpindleGT2 print replaces both the spindle gear and spacer. (assumes…
I picked up a used BeaverTail Stealth 2000 boat off Craigslist. The custom blind is a $400 option and I figured I could print some bimini type brackets and bend some conduit and come up with something similar. Brackets should be useful…
A big windstorm blew off several post caps from my outside decking. Some were lost, others were damaged, basically I was short 6 post caps at $12/cap. I spent a little time in F360 to come up with this replacement cap. This is designed to…
Embroidery hoops that I attach to an xy table for embroidery experiments with an old sewing machine. Instructions Embroidery hoops that can be attached to an xy table to embroider designs with a sewing machine. I used and old Singer. It…
Newer knockdown sock decoys have a pivot which allows them to fold up for easier storage and transport. (see photos of Dive Bomb Snow goose decoys) I had some older Deadly Decoy Canada goose decoys that I decided to update. This was my…
We had some broken frames around the house which needed repair. I saw a similar clamping system and decided it would be an easy print. This design works and I don't intend to update. If I was starting over, I would consider designing the…
This design was inspired by Andy Pugh's videos: I am making my own tips with a 4mm thread and 3mm tip following: In my design, I added adjustment screws to the center hub for aligning concentricity of the tip. I like to 3d print designs…
The GM ignition switch on my RV has a chrome right that is difficult to grasp and tighten. I designed this tool with some lugs to make the job easier. If I had to do it again, I would make the holes larger for fingers or put a square 1/2"…
New-to-me Rockwell vertical milling machine came without a knee crank. Quick design and 3D print of a crank arm and a modified bicycle pedal to the rescue. Print Settings Printer: Jerry's MakerSlide Rafts: No Supports: No Infill: High for…
Last weekend, we had a canoe sliding around on my friend's kayak/canoe trailer. It's a really nice setup with 1 1/4" aluminum tubes but the two canoes on the top had a tendency to slide to the sides. These brackets slip on the horizontal…
I have been pondering how to attach a spindle encoder to my milling machine for rigid tapping. Older vertical mills with pulleys and quills with drawbars pose a problem as there isn't much space or a good place to add an encoder. My…
The tripod mount was getting tipped over and was difficult to precisely locate and rotate, so I printed out an adapter that grips the tripod tube (minus the tripod legs) and mounts to a ThorLabs PR01/M rotation stage. I included the F360…
I was doing an over haul of my Blue Ox towbar. (used to tow a vehicle behind a RV) There are four plastic plugs that prevent dirt/water from entering the tow bar arms. The original plug was a square going into a trapezoid mounted on a…
The factory original plastic engine cover guide cracked (after 20 years of use). I made a few measurements and created a simple design with OpenScad. I printed in red ABS to match the boat. Boat is a CorrectCraft Ski Nautique but other…
Eight years ago, I posted by first design https://www.thingiverse.com/thing:27043 which was a rack stop for a square tube. At that time, I was using sketchup and ABS. I remember it was quite the hassle to design and get the first layer to…
There are several diy board designs for adding an ethernet connection to DSO2000/3000 series oscilloscopes. One such board is available from OSHPark. This design attaches to the OSHPark board to guide and hold it in position. There is an…
Print for strength. I used 0.3mm layers with PolyCarbonate. Just about any filament should work, stronger == better.
I had some porch railings that were treated 2x4s that did not hold paint well. I slipped composite covers over the bottom posts and designed clips to attach to the porch and a custom post cover. I designed a drill guide for drilling…
This is a design for an arbor to hold a cupped grinding wheel in my mill or lathe. This is an example of how a 3D design can be printed to mock up design dimensions. DO NOT USE A 3D PRINTED ARBOR FOR GRINDING (or even spinning). A quick…
I needed to hold a thin walled 1.25" tube in my old lathe with a L00 spindle nose and internal MT4.5 taper. I designed an emergency collet that holds the tube and is compressed by the modified L00 nose protector. I printed in PETG for…
I lost my support to hold the Avian-X turkey decoy in the field. So I decided to update with a 3d printed bearing support mounted to a 1/2"x3/4" wooden stake. The print simple hold the bearings and inserts into the decoy. I applied a…
Simple replacement part to fix a humming bird feeder base. Photo shows original broken base on right, new printed replacement on left. I included F360 file if you need to modify design.
These are all currently available results.
